I did a network test with Passmarks Performancetest. I'm running a 10/100 network with all devices connecting at 100Mb. On Performancetest there are 2 tests to run for Network speed, TCP and UDP. The TCP speed test came back with an average 62000kbps (7.5Mb), and the UDP was 89000kbps (10.8Mb). As I'm running a 100mb network, shouldn't the results of been higher?
View 3 Replies
Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies View RelatedI have upgraded my network service from 2M to 6M per month last week. But the network speed is not so satisfactory. I could hardly feeling its upgrading.Is there any trustful and accurate method or tool to test the network speed?
View 4 Replies View RelatedI have a small network of around 5 PCs,I have 8MB shared connection from ISP,so when I run speed test check from one of my PC it returns around 1.76 Mb download and 0.07 Mb Upload Speed,if I connect one of the PC directly to modem and run the test again so can I get 8MB of speed?
View 17 Replies View RelatedI have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View RelatedI am trying to access a government jobs page to apply for an internship. When I access the page from my home network (using multiple browsers and multiple computers) I get a result that references the job opening from last year, and doesn't have an application button. When I access the site using my 3G connection on my phone, or when accessed from any other internet connection, I get the new page which includes information about the 2013 job opening, and has an application button. When I try to enter the URL for the application page on my home network, I get a 404 error. If I turn my wifi off on my phone and reload the same page, it resolves to the correct page.
View 17 Replies View RelatedI have a cable lan connection for internet.i check speedtest.net for the results and it showed.9mbps download speed and .10 mbps upload speed.but when i download something i only get 0.45 mbps speed.Sometimes i get 9mbps but not often.But speedtest.net always shows my speed to be 9mbps.So that makes me guess , that there is actually 9 mbps available.now how do i utilize it.?
View 8 Replies View RelatedIs there an easy way to test the throughput speed of 2 powerline adapters? I want to know if they are underperforming so I want to rule out my router/internet in this test.
View 5 Replies View RelatedI currently have a 802.11 G router of 54mbps (its claims its a super G 108 mbps tough). My notebooks have 802.11 N built in. Im thinking of upgrading my router to a 802.11 N 300mbps.However, I know that this may be irrelevant unless I have a internet conection that can achieve such speeds. So how do I test my internet speed to see if G is bottlenecking?
View 4 Replies View RelatedI've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies View RelatedI did a simple speed test comparing my EA3500 and Linksys WRT54GL. I used DSL Reports for the test. I was quite shocked and am wondering if the difference is due to the poor wireless driver in the Classic firmware that was updated in the Cloud firmware. Here are my numbers: EA3500, Classic firmware Download average 475 kb/s Upload average 725 kb/sLinksys WRT54GL Ver 1.1 (latest firmware) Download average 3250 kb/s Upload 725 kb/s
Needless to say I have gone back to my trusty WRT54GL until Cisco decides if it will update the Classic firmware and give us 2nd class Cisco customers the same hardware the 1st class Cloud customers have. Time will tell.
I installed an E1200 router today. It automatically upgraded the firmware to the latest when I did this. Everything went smoothly.
I connected my desktop wired and my laptop wireless. I ran three different speed tests: Xfinity, speedtest, and cnet. All three showed 25-35 Mbps download and 4-5 Mbps upload. That is what my old router had too. So far, so good.
I ran the speed test that came with the E1200 router. It showed 0.30- 0.66 Mbps download and 0.58 - 2.09 Mbps upload. Note the decimal points!
Bottom line: The E1200 seems to be working fine, except that its internal speed test seems to be broken, at least when testing from a wired machine.
I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies View RelatedI keep getting "Speed Test: Error occurred during test." message when I run Streamline speed test on N750DB router. I'm not sure what my download and upload speeds are which is why I went with run a speed test to begin with.
View 17 Replies View RelatedWhen I try the Speed Test on my EA6500 I am getting the following message. "The license for this Speed Test has expired. Please contact the webmaster of this site to let them now.".
View 7 Replies View RelatedQuestion re: DIR-655; Hardware ver A4; Firmware version 1.32NA
During bandwidth tests to several sites (principally speedtest.net) I get ping times of 10-11 ms, download speeds of 12+ to 17+ mbps but failure on upload tests using my DIR-655.
When I bypass the 655 and test directly with my cable modem, all (including upload) tests work reliably and consistently.
I have swapped the two ethernet cables involved as well as replacing both with new cables but the results are the same (uploads fail with 655 and work without it)
I have seen several postings over the the last year with this same problem but have never seen any comment from D-Link, or a solution from any reader.
Not that it should have any bearing, but I have TA785GE-128M motherboard and am running Windows 7 (patch current) on COMCAST
is this problem acknowledged by D-Link and is there a solution?
I've been having problems downloading full ISO's before they're interrupted. There doesn't seem to be any real rhyme or reason to it. Sometimes a 4.1GB ISO will stop at 2GB, other times at 4.0GB. I realize I could run a ping from the time I walk in until the time I leave, but that seems a bit too archaic of a solution.nfortunately, our CTO believes SNMP is too much of a security risk
View 11 Replies View RelatedI know ping and traceroute are commands that test network connectivity. what about netstat and telnet? can they also test network connectivity?
View 4 Replies View RelatedI am used to lan testing with QCheck and Passmark's Performance Test (Network Test). But recently I upgraded to a 10 GbE switch (Netgear M7100), and it broke QCheck; basically, QCheck gave me an infinity as the result of my throughput test. Passmark performed fine, but it's just a hassle to use (or at least it's not as straight forward as QCheck).
Is there another free tool for network lan speed tests? Or is there a really cheap tool for it?Let's say I have less than 20 devices to test on.I've already tried Totusoft's lan speed test and find that its free version is useless.I'm having an itch write my own software now, but if it comes to that, I'd rather pay for a cheap software.Spent too much money on upgrading already - switches, servers, and computers)
how do I set up a test domain? I'm running Server 2008 std and have not gotten the DNS server configured right. I'm looking for a guide to take me through the process so I can experience success and get the feel of a working LAN.
View 2 Replies View RelatedI have been having an issue with my system recently. When online I will be browsing and my connection will be knocked off. The vodafone page will come out showing connect and diagonise tabs. I did a computer network diagnostic check and it says: "DNS server isn't responding"
View 4 Replies View RelatedI am working with a client who is adamant their backbone is fine. However, I am unable to get a single iperf connection to generate anything more than 9.5 megabit/s, and can go all the way up to 322 megabit/s with multiple streams before it looks like we are saturated. Note the example below for a single stream has a 1MByte window, with 8kb we were only able to see 2.4 mbits/sec per stream (as seen in the per stream in the example below). Where would you begin to look for why we cant seem to exceed 2.3mbit/s with an 8kb window, or 7.88 with a 1mbyte.
View 14 Replies View RelatedI'm using an Acer Aspire 5532 and just recently set up my own network with my Cisco WRT120N router. I used the installation disc and set up a WPA password, named my router, and my network. For the installation, it seemed I could not even start without physically linking the router to my laptop with the included rollover cable. I finished that, and ever since my wireless adapter has been disabled. Whenever I attempt to enable it, I get an error; my laptop shuts down and I'm presented with blue screen. The only way I've been able to get back to normal is to reboot in safe mode and than do a system restore.
View 3 Replies View RelatedI have 100mbps connection but when i took the test at speedtest.net it was so slow i don't understand whats bottle necking my system. When i download games off of steam it downloads its much faster then downing anything from my browser. I know its my network because when i went on steam and changed my download settings to cable and it was fixed.
View 9 Replies View RelatedI have been put in charge of getting a failover cluster up and runing for SQL AlwaysOn. My equipment is a Cisco SF300-24 and a Cisco 2024 smartswitch. Now I am really new at this since my CCNA class has not yet started but I am trying to get a headstart. What I need to do is split the network up into 2 vlans to represent my data center, and the network oporation center. Ports 1,2,and 3 will be my DC; 11 and 12 will be my NOC. I need to learn how to get those two vlans to communicate. trunk? how? I need the computers to communicate flawlessly. I would rather use the Cisco CLI and not the GUI, google is coming up with nothing descriptive.
View 14 Replies View RelatedJust setting up and testing a Cisco 891-K9 router. Used CCP for basic setup, figure I'll tweak any settings needed later.For the firewall, I chose the default "medium" security setting in CCP, then added some holes (already setup in NAT) for outside access in.
Now on to the real question:I noticed that I am now unable to click through google search results. On any borwser. Clicking on any search result simply loops back around to the same google search page. If I disable Javascript on the browser, everything works as expected. So it appears that the firewall is preventing something in google's scripts from redirecting and "clicking through" to the final destination page.
I'm familiar with our old Pix firewall commands, but still a relative newcomer to the zone based firewall and commands for this new 891, (relevant Config pasted below) (Gi0 is the WAN interface)
!
!
multilink bundle-name authenticated
parameter-map type protocol-info yahoo-servers
server name scs.msg.yahoo.com
server name scsa.msg.yahoo.com
server name scsb.msg.yahoo.com
[code]....
I have a ASA 5505 as a default gateway to a network, whenever I tracert to outside it shows every hop ip address as the ip address I'm trying to get too, quick example
lets say I'm in a 192.168.0.0/25 network but I want to trace to 10.10.10.10
Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
I'm trying to block access to dropbox.com on our ASA5510. I have it setup and it blocks dropbox.com just fine. But it is also blocking google.com. I can't figure out why.
Here's my config. When it blocks google, it blocks it with the terminated by inspection engine, reason - disconnected, dropped packet.
regex Block_Dropbox ".dropbox.com"
access-list URL_Filtering extended permit tcp any any eq www
access-list URL_Filtering extended permit tcp any any eq https
[Code]......
Why does the sx300 series only displays ping and traceroute results in 20ms intervals (see below)? The example in the CLI manual shows "regular" results. These 20ms intervals are not useful for troubleshooting. This is version 1.1.0.73 on an sf300-24. [code]
View 2 Replies View RelatedWe have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
Tried everything from changing the cables to changing the end device but no luck with it.
Module results show pass and no errors in the logging.
I setup a network to run my business three years ago. It consists of 7 computers, an HP Media Smart server, three Netgear GS 605 v 3, where I connect the computers, router and printers.The server is only used as a file server and runs the backups. However, I also put together an Access database which has a front end on each computer and a back end on the server.Reading data from the database on some machines is terribly slow at times, 30 seconds or more for a response, but other times it is almost as quick as you can type.We are a lot busier now so do I need to upgrade hardware or do I have a problem. For example, my machine is just a Vista machine and writes to server at 60Mbps and reads at 21Mbps, two other Windows 7 machines write at 70Mbps but only read at 3Mbps. If I look at the Status of my Local Area Connection Status, its speed is 100.0 Mbps yet the Netgear states 10/100/1000. I have concluded that I need to change the network cards in the computers, but I don't know if I am correct.
View 3 Replies View Related2 pcs connected with a TPlink modem/switch. wired connection.One pc running win7 64, other xp sp3. Both home pcs..Used to get about 10mbs transfer speed. ( I know its low, but was more than happy with it as I never use it to transfer large files.But suddenly transfer speed changed to just 8kbps. Its kind of a speed limit activated.I can just browse files and folders but cannot copy at 8kbps.
View 12 Replies View Related
