Cisco Wireless :: Results From Dot11 Link Test On 1400 Bridges?
Sep 11, 2012Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies
ADVERTISEMENT
Network Speed Test Results?
Jan 10, 2011I did a network test with Passmarks Performancetest. I'm running a 10/100 network with all devices connecting at 100Mb. On Performancetest there are 2 tests to run for Network speed, TCP and UDP. The TCP speed test came back with an average 62000kbps (7.5Mb), and the UDP was 89000kbps (10.8Mb). As I'm running a 100mb network, shouldn't the results of been higher?
View 3 Replies View RelatedD-Link DIR-655 :: Upload Test Error Test With Speednet
May 3, 2011Question re: DIR-655; Hardware ver A4; Firmware version 1.32NA
During bandwidth tests to several sites (principally speedtest.net) I get ping times of 10-11 ms, download speeds of 12+ to 17+ mbps but failure on upload tests using my DIR-655.
When I bypass the 655 and test directly with my cable modem, all (including upload) tests work reliably and consistently.
I have swapped the two ethernet cables involved as well as replacing both with new cables but the results are the same (uploads fail with 655 and work without it)
I have seen several postings over the the last year with this same problem but have never seen any comment from D-Link, or a solution from any reader.
Not that it should have any bearing, but I have TA785GE-128M motherboard and am running Windows 7 (patch current) on COMCAST
is this problem acknowledged by D-Link and is there a solution?
Cisco Wireless :: 1410 Bridges Link Fail?
Jun 22, 2011I have a point to point link of 9.27 km using 1410 bridges and AIR-ANT58G28SDA-N antennas as per the documentation that would be an easy to deploy link and it should work at 54 Mbps, eventhough it drops the link, it's so slow and the power measurments indicate -70 dbm (aprox) right under the antenna which is at 9 m height.
This is not the first time I have troubles with 1410 bridges, the other two times I had to change them for 1310 bridges. I wonder if it has to do with some configuration tunning like, external antena gain, link distance or anything else? By the wat this is ocurring in México don't know if that might be worth of taking into consideration in order to deploy a 1410 link.
Cisco Wireless :: WLC 5508 - Link Test Fails?
Jan 10, 2013I have a WLC5508 working fine right now, using IOS 7.3
When I try to do a Link test on some users to check signal quality, noise, etc... I received the error message below
Cisco Wireless :: 3502i - Dot11 Interface Shutdown
Dec 15, 2012My 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
______________
interface Dot11Radio0
no ip route-cache
shutdown
antenna gain 0
beamform ofdm
mbssid(code)
TP-Link ADSL2+ Wireless :: TD-W8980 Test DNS Root
Feb 18, 2013Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Another query regarding diagnostic test and Test DNS Root. It always fails why?
Cisco Wireless :: AP1041N - Show Dot11 Associations Does Not Track Anything
Jan 30, 2013I'm trying to track associations on one of my AiroNets (AP1041N) using the show dot11 associations command, but it does not show anything! e.g.AP1#show dot11 associations allAP1#show dot11 associations all-clientAP1#show dot11 associationsAP1# Is there something I need to enable in the configuration to track associations like this?
View 1 Replies View RelatedCisco Wireless :: Sh Dot11 Associations Client Command On 1811w?
Oct 23, 2012Wireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
TP-Link ADSL2+ Wireless :: TD-W8960N / How To Test Routers Ddns
Jan 30, 2013Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.54317n
ISP : century link
How do I test my routers ddns? My computer went down. So, my adsl ip address changed. I caused the modem/router to reboot. But the new ip wasn't sent to the Host (dyndns.org). I had to update my ip manually on [URL].
Cisco Wireless :: Aironet 1240 Snmp Oid To List Dot11 Associations
Oct 18, 2012We successfully use this oid on our Aironet 1240 series AP's to list the dot11 associations to the AP:1.3.6.1.4.1.9.9.273.1.2.1.1.18 (cDot11ClientSubIfIndex).However, that oid does not work on our Aironet 1140 series AP's. Any equivalent oid?
View 0 Replies View RelatedTP-Link 150Mbps Wireless :: TL-WR740N - Network Status Test Failed
Feb 4, 2013Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
Re-enable Wireless Adapter Results In Laptop
Sep 23, 2011I'm using an Acer Aspire 5532 and just recently set up my own network with my Cisco WRT120N router. I used the installation disc and set up a WPA password, named my router, and my network. For the installation, it seemed I could not even start without physically linking the router to my laptop with the included rollover cable. I finished that, and ever since my wireless adapter has been disabled. Whenever I attempt to enable it, I get an error; my laptop shuts down and I'm presented with blue screen. The only way I've been able to get back to normal is to reboot in safe mode and than do a system restore.
View 3 Replies View RelatedCisco WAN :: MDS9000 / DWDM - How To Test Link
Aug 2, 2011I have recently set up a MDS9000 san fabric in two locations connected by DWDM. My DWDM links come up fine but I am looking to test this link before we go live. How to test this?
View 1 Replies View RelatedCisco Wireless :: Aironet 1400 Bridge FIPS Compliance?
Aug 14, 2012Is the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedCisco Wireless :: Interface Radio0-802.11A With CRC Errors 1400 Series
Nov 1, 2011I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies View RelatedCisco Wireless :: 1131AG APs As Bridges?
Feb 27, 2012I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedDell Vostro 1400 Laptop Unable To Use Wireless Internet?
Jun 11, 2011Today after I restarted my laptop (Dell vostro 1400 running windows), I found that I can't open any pages or sites. My wireless utility icon tells me that my laptop is connected to my router, but neither of my browsers (chrome or firefox) will load anything. However, if I turn off my wireless (there's a switch that I can trigger) and try to load a page immediately after turning it back on, then a page will load, though anything after that will not. I'm positive that it's not my router or my internet because my computer and iPod touch connect perfectly fine, it's just my laptop will not.I thought that I might have accidentally gotten malware so I ran malwarebytes in safe mode and it found one Trojan, which I removed afterwards, though I don't remember what it's name or type was. I restarted my laptop afterwards hoping that removing the Trojan would work but I'm still having the same problem.
View 1 Replies View RelatedDell :: Vostro 1400 / Wireless - Smart Phone Hotspot?
Jan 5, 2012I have a Vostro 1400 and my OS is Windows XP. I just bought an Android Smart Phone, my carrier is Sprint.
I have portable ‘Hot Spot’ service. However, I can’t find a wireless program on my computer.
I swapped out my original hard drive after it crashed. I thought that I reloaded everything onto the new one.
Cisco :: Aironet 1210 - Sleep Mode Causes 0.0.0.0 Dot11 Association
May 20, 2012I'm using aironet 1210, 1130, 1100, 1040 autonomous mode, in a University campus network with thousands of daily user.We're using RADIUS authentication and AES/WPA2.In the past, there were some major issues with traffic (broadcast / multicast) in the wireless networks, that would spread all around the campus causing excessive processing at the access-points.To solve the problem we decided to implement access list at the radio interface to drop all the unwanted traffic. [code]
I'm pretty sure this is caused by the ACL (I've tested removing the ACL and the issue never occurred) but I can't just get ride of it.
Any alternative way to drop broadcasts?
Cisco Wireless :: Aironet 1260 As Bridges?
Feb 2, 2012Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
Dell :: Vostro 1400 Cannot Access Any Wireless Or Network Via Hard Wire
Sep 5, 2012Today I replaced my motherboard to fix the graphics card issue on my Vostro 1400. After installing the motherboard I installed the driver's from Dell's site for the networking card.
I get an error stating device driver/software was not successfully installed. I tried a restore point, that didn't work either. I tried the original driver disc that came with the laptop - same problem.
In device manager it is showing: broadcom netlink adapter fast ethernet #2 - does that mean it thinks I have more than one network card? I'm not sure what to do next. I can't access any wireless from that laptop, not even from a hard wire.
I'm running Windows 7 32 bit.
Cisco Wireless :: 1300 Multiple VLANs Between The Bridges
Feb 20, 2008I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies View RelatedCisco Wireless :: BR1410A-E-K9 Adding Two More Bridges EtherChannel
Jan 13, 2013Two facilites are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly. and we wanted to achieve it by doing some kind of etherchannel in the switches at each location.
View 4 Replies View RelatedCisco Wireless :: 1310 Bridges Keep Losing Connection?
Nov 28, 2010I have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection. When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)
Cisco Wireless :: AIR-BR1410A-E-K9 Adding Two More Bridges / EtherChannel
Dec 3, 2012Two facilities are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly.and we wanted to achieve it by doing some kind of etherchannel in the switches at each location..
View 7 Replies View RelatedCisco Wireless :: Combining 1310 Bridges With 5508 Controller
Jul 10, 2012I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View RelatedCisco Wireless :: 1300 Series Bridges Load Balancing
Apr 6, 2008Is it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies View RelatedLinksys Wireless Router :: Can E1200 Be Bridges Wirelessly
Sep 26, 2012Can the e1200 be bridges wirelessly? Or does it have to hardwired?
View 7 Replies View RelatedWireless Bridges To Pair Up With Netgear WNDR 3700?
Oct 13, 2011I bought this wireless router about a year+ ago, and it's just great. It's attached to the cable modem "downstairs" and right now it supports 2 smartphones wirelessly plus an ancient wired cable to an "upstairs" home office.
I'd like to improve overall performance with a wireless bridge to a gigabit hub in the upstairs office. I'd also like to add a second wireless bridge so I can stream movies to a box that would be attached to my TV, which does not have built-in wireless access.
Trendnet seems to have some interesting wireless bridges, but in the past I had a Trendnet wireless router with really, reallly bad software.
Cisco :: Troubleshooting Iperf Results Over Infrastructure
Mar 19, 2013I am working with a client who is adamant their backbone is fine. However, I am unable to get a single iperf connection to generate anything more than 9.5 megabit/s, and can go all the way up to 322 megabit/s with multiple streams before it looks like we are saturated. Note the example below for a single stream has a 1MByte window, with 8kb we were only able to see 2.4 mbits/sec per stream (as seen in the per stream in the example below). Where would you begin to look for why we cant seem to exceed 2.3mbit/s with an 8kb window, or 7.88 with a 1mbyte.
View 14 Replies View RelatedDifferent Page Results Depending On Network?
Oct 20, 2012I am trying to access a government jobs page to apply for an internship. When I access the page from my home network (using multiple browsers and multiple computers) I get a result that references the job opening from last year, and doesn't have an application button. When I access the site using my 3G connection on my phone, or when accessed from any other internet connection, I get the new page which includes information about the 2013 job opening, and has an application button. When I try to enter the URL for the application page on my home network, I get a 404 error. If I turn my wifi off on my phone and reload the same page, it resolves to the correct page.
View 17 Replies View RelatedBelkin Routers :: N300 Wireless Bridges Be Connected To Same Access Point
Nov 21, 2012Can 2 N300 wireless bridges be connected to the same wireless access point ?
View 1 Replies View Related