Cisco Wireless :: 1410 Bridges Link Fail?
Jun 22, 2011
I have a point to point link of 9.27 km using 1410 bridges and AIR-ANT58G28SDA-N antennas as per the documentation that would be an easy to deploy link and it should work at 54 Mbps, eventhough it drops the link, it's so slow and the power measurments indicate -70 dbm (aprox) right under the antenna which is at 9 m height.
This is not the first time I have troubles with 1410 bridges, the other two times I had to change them for 1310 bridges. I wonder if it has to do with some configuration tunning like, external antena gain, link distance or anything else? By the wat this is ocurring in México don't know if that might be worth of taking into consideration in order to deploy a 1410 link.
View 3 Replies
ADVERTISEMENT
Sep 11, 2012
Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies
View Related
Aug 8, 2011
Point to point wireless connectivity configuration procedure using 1410 bridges either using GUI/CLI .
We have setup this in one of our Client sites.
View 1 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Feb 22, 2013
Region : China
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
tried to run the easy setup assistant but failed the connection test. The WLAN indicator did not flash or light up, don't know if that is the problem.
Have checked the cables and they are working fine. As this router is 3 yrs old, should I get a new one? Does it appear to be a hardware problem?
View 7 Replies
View Related
Dec 27, 2012
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies
View Related
Aug 2, 2011
security configuration of the 1410 bridge and on how to test the bandwidth/throughput between two 1410 Bridges setup for point-to-point connectivity.
We have setup this in one of our Client sites.
View 3 Replies
View Related
Nov 10, 2011
Just recently upgrade our 2 5508 controllers from 6.0.199.0 to 7.0.116.0. Since that upgrade, I have a handful (8 to 10) of wireless laptops that now refuse to associate to any access points. The thing these laptops all have in common is some variation of the Intel Wifi Link AGN cards. I have about 200 other clients out there working just fine.
I've tried everything under the sun that I can think of. Patches, drivers, the whole sh'bang.
Is there a known issue with 7.0.116.0 and these particular cards?
View 17 Replies
View Related
May 13, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
wdr3500 problem with usb external hard drive when I try to transfer files from computer to usb on the router it'll work for small files like MP3. But files like MKV where they can be 1-2gb will cause a disconnect and fail to transfer the file. The whole drive would disconnect and windows will give an I/O error.
View 8 Replies
View Related
Feb 21, 2012
I have two 1410 bridges installed in a point to point link using external directional antennas. The distance between the bridges is only 200M. As you can see below from the output the RSSI and SNR are excellent with a good fade margin available. These stats are almost identical to what my path profile calculated out to be. During normal operation the latency on this link sub 2ms, during certain conditions the latency jumps to 40+ms and starts dropping packets. I say certain conditions because we have not been able to pinpoint it. Unfortunately at this time the customer does not have the ability to do any SNMP polling or collect any statistical information (working on getting this setup). There are an excessive number of data retries and am not sure if that is normal. During the issues I have observered the below command output and the numbers did not change, which leads to me believe that it is not a RF issue. It almost looks like it's serialization delay, but I have no data to back that up. During iperf performance testing of this wireless link I could push 54Mbps of UDP traffic no problem, no errors, no CRC's.
Bridge Parameters
Encryption: WPA-PSK w/TKIP
Distance parameter: Configured to 1
[Code].....
View 4 Replies
View Related
Apr 18, 2013
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies
View Related
May 31, 2011
I have recently had to deploy a 1410 in a Root/Non-root bridge configuration to expand a terrestrial network across to an uncabled area.
All switches in play are 2960 series and the bridge is running with multiple Vlans.
Basic config as follows.
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname BRIDGE001!no logging consoleenable secret 5(code)
View 1 Replies
View Related
Apr 19, 2011
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies
View Related
Feb 27, 2012
I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies
View Related
Feb 2, 2012
Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
View 10 Replies
View Related
Feb 22, 2012
We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.
View 3 Replies
View Related
Feb 20, 2008
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies
View Related
Jan 13, 2013
Two facilites are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly. and we wanted to achieve it by doing some kind of etherchannel in the switches at each location.
View 4 Replies
View Related
Nov 28, 2010
I have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection. When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)
View 12 Replies
View Related
Dec 3, 2012
Two facilities are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly.and we wanted to achieve it by doing some kind of etherchannel in the switches at each location..
View 7 Replies
View Related
Jul 10, 2012
I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies
View Related
Apr 6, 2008
Is it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies
View Related
Sep 26, 2012
Can the e1200 be bridges wirelessly? Or does it have to hardwired?
View 7 Replies
View Related
Oct 13, 2011
I bought this wireless router about a year+ ago, and it's just great. It's attached to the cable modem "downstairs" and right now it supports 2 smartphones wirelessly plus an ancient wired cable to an "upstairs" home office.
I'd like to improve overall performance with a wireless bridge to a gigabit hub in the upstairs office. I'd also like to add a second wireless bridge so I can stream movies to a box that would be attached to my TV, which does not have built-in wireless access.
Trendnet seems to have some interesting wireless bridges, but in the past I had a Trendnet wireless router with really, reallly bad software.
View 10 Replies
View Related
Dec 1, 2012
I have 3 switches
Catalyst 2960
Catalyst 3750
Hp procurve 1410 24g
I want to link them using fiber as they are almost 50 meters apart. What connectors should I use and what fiber optic cable can be connected to those connectors.I have found these connectors and cables on internet will these work
GBM-7000-S85 - 1000Base-SX, multi-mode, 550m, 850nm GBIC transceiver
SC to SC Multimode Duplex High Speed Fiber Optic Ethernet Patch Cable 62.5/125
View 1 Replies
View Related
May 20, 2012
Whenever I use my router web pages often fail to load. Then after about 30 or seconds or so it will start working again. Even worse,if I go to game online I will have lag like crazy. Even if I am the only one on the router.I'm using a D-Link n300 gigabit router.
View 5 Replies
View Related
Sep 27, 2012
I have a Ubiquiti radio link between my DSL modem and RV082 router and although the router log states that it is connected to the static ip address of the modem i get and NSD fail and have no connection. if I plug the radio link directly into a computer with the static ip I get a connection but the modem has a problem with it.
View 1 Replies
View Related
Mar 10, 2013
Region : Denmark
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
I have a TL-MR3420 router placed in a remote location. The internet connection is via 3G, and since the telco is shifting the IP every 24 hours, the router is configured with DDNS from no-ip.org. This is working OK most days, but sometimes the DNS fails to update. To be able to trobleshoot it, I am trying to make my router send a mail with the logfile every hour. This function seems to be easy and out-of-the-box, but it doesn't wiork. Whenever I try to mail the log I get the error message "Fail to Connect the mail server.".
It is not possible to enter another SMTP-port, so I asume the standard port 25 (like this thread). Most ISP-mail services require SSL/TLS and/or use an alternative port, so I have made my own server. This server is visible on the Internet, and I (and others) are able to connect and send mails using smtp on port 25. But, still my remote TL-MR3420 keep saying "Fail to Connect the mail server.". I have tried nearly everything, including disabling authentication and giving the IP-address of the smtp server directly instead of the URL.
View 1 Replies
View Related
May 21, 2011
My dcs 2121 ip camera was working fine till I tried to update firmware 1.05(update_DCS-2102_DCS-2121_1.05_patch01_4927.bin). The IE screen mentioned update was ok(Firmware update successful:The camera will now reboot, please wait for 0 seconds) but my IP camera never come back after reboot! the red light in front never goes off. The camera is connected to my Windows 7 PC directly through a a network cable. no able to rest the camera as well .
View 5 Replies
View Related
Nov 21, 2012
Can 2 N300 wireless bridges be connected to the same wireless access point ?
View 1 Replies
View Related
Feb 6, 2012
Okay so I have been using my E4200 router and WET610N bridges for a while now without any issues really until yesterday when I updated the firmware on the 4200 now none of my WET610N's (I have 2) can connect via wireless at all. At first I thought it was a a wireless issue but I have other devices that connect up just fine via wireless.I've made no changes to the router or the bridges before the firmware update.
If I hook the bridge directly to the router I can access it and configure it, but looking at the "Status" page, I see the bridge try and connect wirelessly but is quickly disconnected. Range isn't an issue as in my testing the bridge was 2 feet from the router.I've update the bridges to the latest firmware and have verified a 100 times that the settings on both my router and the bridges are set correctly (when the bridges are hooked up via network card).
View 1 Replies
View Related
Jan 11, 2012
I have 2 Media Bridges, a Trendnet TEW-640MB and TrendNet TEW-680MB. Both are set as a Static IP on the devices 192.168.1.150 and 192.168.1.151. In the DHCP table for my E4200 I don't see those. I have no problem accessing them typing in those IP addresses but wondering why they don't show up in the table.Actually looking at it more closely, the devices hooked up that are active seem to show up.So I see the following below. And where is list LAN but no name those seem to be devices connected to the media bridges.
LAN192.168.1.128 LAN192.168.1.129 iPhoneWireless192.168.1.130 1 Wireless192.168.1.131 LAN192.168.1.135
View 2 Replies
View Related
Apr 12, 2012
I have a toshiba satellite 1410 s173 laptop running windows xp.It has a 3 com megahertz 3cxm 356 modem with a yelleow exclamation point beside it, with a code ten error in device manager.
View 1 Replies
View Related
