Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedWe have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.
View 1 Replies View RelatedDo we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies View RelatedI would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies View RelatedIs Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies View RelatedI was wondering if its possible to setup the Cisco Aironet 1260 as a WDS master with radius and another Cisco Aironet 1260 as a slave for seamless roaming. How many slaves can a WDS master handle?
View 1 Replies View RelatedI have CISCO ACS 5.1 radius for VPN on ASA and tried to configure an NDG on it for AIRONET 1260 too and worked fine with IEEE 802.1x CISCO EAP-FAST authentication As I had some trouble to let users to authenticate only on VPN if are VPN users and only on CISCO AIRONET if need only WIFI AIRONET I tried exception policies rules but something not working. VPN was ok but not WIFI access denied for rule policy access I decided to install CISCO ACS 4.x on Windows 2003 that is on ACS 5 DVD I created NDG as done on ACS 5 put a shared secret , put on AIRONET too as done for ACS 5 but I receive an error against ACS 4.x To troubleshout it I tried [URL] but not work ! I think to have done all fine owever on ACS 5 it worked in 5 minutes I searched log inside ACS 4 and found "Invalid message authenticator in EAP request" and I found this: [URL]Changed shared secret more times but ever not workign with ACS 4 I need to have user and password prompt on client trying to authentincate on AIRONET WIFI and I need ACS INTERNAL USER no active directory, no LDAP , no external user database?
View 1 Replies View RelatedI have 3 Aironet 1260's with the same SSID and set with Open Authentication with MAC Authentication. Can I designate one of the 1260's as the MAC Authentication Server? I have all 3 now working with MAC Address Authenticated ty Local List Only and have to put the new MAC address in all 3.
View 3 Replies View RelatedWe have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies View RelatedI can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedWhat is the most current version oF IOS for the following Wireless AP(Aironet 1260)
Product/Model Number: AIR-AP1261N-E-K9
System Software Filename: ap3g1-k9w7-tar.124
We are installing 1260 Access Point (AIR-LAP1262N-E-K9) with 2 sets of external antenna:AIR-ANT2460NP-R (2.4Ghz, Patch Wall-mount, 6dBi Directional) & AIR-ANT5160NP-R (5Ghz, Patch Wall-mount, 6dBi Directional).What would be the recommended separation of the 2 antennas if they will be mounted beside each other?
View 1 Replies View Relatedi have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies View Relatedi have Cisco WLC 2504 & 1260 LAP.i connect the WLC to L3 switch & connect the LAP to another port in the same L3 switch.i configure DHCP on the same switch to provide ip for the LAP , but the LAP can't get an ip address and can't joint the controller.also if when i login to the LAP i can't enter the configuration mode.
View 6 Replies View RelatedSo I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
VLAN 1
And
VLAN 10
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN).
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies View RelatedTwo facilites are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly. and we wanted to achieve it by doing some kind of etherchannel in the switches at each location.
View 4 Replies View RelatedI have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection. When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)
Two facilities are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly.and we wanted to achieve it by doing some kind of etherchannel in the switches at each location..
View 7 Replies View RelatedI have a point to point link of 9.27 km using 1410 bridges and AIR-ANT58G28SDA-N antennas as per the documentation that would be an easy to deploy link and it should work at 54 Mbps, eventhough it drops the link, it's so slow and the power measurments indicate -70 dbm (aprox) right under the antenna which is at 9 m height.
This is not the first time I have troubles with 1410 bridges, the other two times I had to change them for 1310 bridges. I wonder if it has to do with some configuration tunning like, external antena gain, link distance or anything else? By the wat this is ocurring in México don't know if that might be worth of taking into consideration in order to deploy a 1410 link.
good docs for configuring a 1260 autonomous AP?
View 1 Replies View RelatedI am looking to slowly migrate some of our wireless devices (Aironet 1231 and 1232's) to the Wireless N spec - 1260's.I currently have four AP locations that I want to upgrade first before anywhere else. At the minute, these four AP's work on the 2.4Ghz G band.
how the new 1260's will work in the mixed environment. I believe I will need to purchase the 1262 (which is the dual band version) so that I can operate the AP in both the 2.4Ghz G band range and the 5Ghz N range at the same time, is this correct?If I was to purchase the 1261 (which is the single band version), will I only be able to operate in either th 2.4Ghz or 5Ghz, but not at the same time?
For the mixed environment, would you suggest the dual band version? Can I place the same SSID on multiple Radios if this is the case? Following example: Say I have the SSID called 'Company' - this at the minute is operating on the G band 2.4Ghz range. If I was to purcahse the dual band 1262, could I put this SSID on both the G radio and the N radio? Would clients with an N adapter automatically connect to the 5Ghz range (N Radio) and legacy G and B adapters automatically connect to the 2.4Ghz (G Radio)?
I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View RelatedIs it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies View RelatedCan the e1200 be bridges wirelessly? Or does it have to hardwired?
View 7 Replies View RelatedI bought this wireless router about a year+ ago, and it's just great. It's attached to the cable modem "downstairs" and right now it supports 2 smartphones wirelessly plus an ancient wired cable to an "upstairs" home office.
I'd like to improve overall performance with a wireless bridge to a gigabit hub in the upstairs office. I'd also like to add a second wireless bridge so I can stream movies to a box that would be attached to my TV, which does not have built-in wireless access.
Trendnet seems to have some interesting wireless bridges, but in the past I had a Trendnet wireless router with really, reallly bad software.
iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedJust did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies View RelatedI'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again
View 2 Replies View RelatedRecently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
i have 2 1260 Access points one is in root mode , one is wgb mode. Authentication is EAPFAST. There are 5 devices connected via WGB bridge to the rest of the network.
- If clients are sending some data , then WGB AP announces this client mac via IAPP to root AP and rest of the network sees them correctly
- If clients are "passive" , then after WBG AP announces them to root AP , they timeout after 6 minutes on root AP and obviously they are not pingable from the rest of the network. The only way to restore connectivity is to ping that device from WGB AP, then WGB AP announces via IAPP to root AP , then and only then they become visible from the rest of the network.
My question is related to this 6 minute timeout on root AP . Is it normal behaviour ?
Can 2 N300 wireless bridges be connected to the same wireless access point ?
View 1 Replies View Related
