i have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 RepliesI have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
I got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies View RelatedWe are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies View RelatedI need to upgrade the fwsm image from 3.1(10) to 4.0(8). Can i do it directly from 3.1(10) to 4.0(8) ?Do i need to upgrade other image also along with Firewall version 4.0(8)?
[code]....
I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedI wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies View RelatedI have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedI own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies View RelatedI upgraded my WISM software to v. 7.0.116.0. The upgrade went smoothly. Most of my WAPs are H-REAP and they are working fine. I have a few local mode WAPs that are stuck in a downloading state. They will try to download, reboot, then try to download again. This is happening only with the WAPs in local mode. These WAPs were working before the upgrade.
View 2 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedHow can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View RelatedI want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third party Like [URL]
View 1 Replies View RelatedWhat is the most current version oF IOS for the following Wireless AP(Aironet 1260)
Product/Model Number: AIR-AP1261N-E-K9
System Software Filename: ap3g1-k9w7-tar.124
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedIs it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
We are installing 1260 Access Point (AIR-LAP1262N-E-K9) with 2 sets of external antenna:AIR-ANT2460NP-R (2.4Ghz, Patch Wall-mount, 6dBi Directional) & AIR-ANT5160NP-R (5Ghz, Patch Wall-mount, 6dBi Directional).What would be the recommended separation of the 2 antennas if they will be mounted beside each other?
View 1 Replies View Relatedi have Cisco WLC 2504 & 1260 LAP.i connect the WLC to L3 switch & connect the LAP to another port in the same L3 switch.i configure DHCP on the same switch to provide ip for the LAP , but the LAP can't get an ip address and can't joint the controller.also if when i login to the LAP i can't enter the configuration mode.
View 6 Replies View RelatedSo I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
VLAN 1
And
VLAN 10
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN).
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..
good docs for configuring a 1260 autonomous AP?
View 1 Replies View RelatedI am looking to slowly migrate some of our wireless devices (Aironet 1231 and 1232's) to the Wireless N spec - 1260's.I currently have four AP locations that I want to upgrade first before anywhere else. At the minute, these four AP's work on the 2.4Ghz G band.
how the new 1260's will work in the mixed environment. I believe I will need to purchase the 1262 (which is the dual band version) so that I can operate the AP in both the 2.4Ghz G band range and the 5Ghz N range at the same time, is this correct?If I was to purchase the 1261 (which is the single band version), will I only be able to operate in either th 2.4Ghz or 5Ghz, but not at the same time?
For the mixed environment, would you suggest the dual band version? Can I place the same SSID on multiple Radios if this is the case? Following example: Say I have the SSID called 'Company' - this at the minute is operating on the G band 2.4Ghz range. If I was to purcahse the dual band 1262, could I put this SSID on both the G radio and the N radio? Would clients with an N adapter automatically connect to the 5Ghz range (N Radio) and legacy G and B adapters automatically connect to the 2.4Ghz (G Radio)?
iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedI'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedWe have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.
View 1 Replies View RelatedDo we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies View RelatedI'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again
View 2 Replies View RelatedI would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies View RelatedRecently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?