I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Repliesafter upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24
Vlan 20 = 192.168.0.1/24
ME2400 firmware
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1)
[Code]...
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies View RelatedI'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies View RelatedI upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies View RelatedI have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedI wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies View RelatedI own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
How can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 Replies View RelatedDue to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode. When i look at the version i See that bootloader is still the old version 12.2.58. It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
View 8 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View RelatedI want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third party Like [URL]
View 1 Replies View RelatedI was in the process of recovering a password on a nexus 5548 swith when it finally gets in to the boot mode.I think i lost all my bootloader code.How do i get it back on the switch
loader> load n5000-uk9.5.0.3.N2.1.bin
Error 27: Unrecognized command
how to restore my IOS on this device
I've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image. The processing engine I have is the NPE-G1 and I'm looking for an upgradeable ROMMON image or a reason why the boot is taking this long.
View 1 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies View RelatedWe deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies View RelatedI've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue.
CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 8 59 135 0.00% 0.00% 0.00% 0 Chunk Manager
2 58864 3290773 17 0.00% 0.00% 0.00% 0 Load Meter
3 1784 238001 7 0.07% 0.01% 0.00% 2 Virtual Exec
[code]....
I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
How do I add network drivers to a wds boot image on 2003R2. I see that 2008 has the add driver option but that doesn't exist in 2003r2.
View 1 Replies View RelatedI have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies View Related128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
I want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?