Cisco Wireless :: New AIR-LAP1142N-A-K9 Insufficient Memory To Boot Image
Nov 1, 2011
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
View 7 Replies
ADVERTISEMENT
Sep 22, 2012
I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
View 1 Replies
View Related
Oct 3, 2011
When I try to save the configuration it displays the following error.Is it due to insufficient memory?
MPF-ASA#wr mem
ERROR: % Unrecognized commandMPF-ASA(config)# wr memBuilding configuration...Cryptochecksum: 81c514b8 9e95ee97 8b512148 b31377a4
[Code]...
View 1 Replies
View Related
Feb 6, 2011
When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies
View Related
Dec 30, 2011
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
View 6 Replies
View Related
Apr 29, 2012
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies
View Related
Nov 27, 2011
I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
View 1 Replies
View Related
Dec 29, 2011
I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
View 3 Replies
View Related
May 1, 2011
I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
View 1 Replies
View Related
Oct 24, 2012
I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
View 1 Replies
View Related
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
May 27, 2013
i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
View 1 Replies
View Related
May 13, 2013
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies
View Related
May 18, 2013
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
View 7 Replies
View Related
Jan 25, 2013
How do I add network drivers to a wds boot image on 2003R2. I see that 2008 has the add driver option but that doesn't exist in 2003r2.
View 1 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Jan 22, 2008
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
Feb 28, 2011
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
View 1 Replies
View Related
Sep 29, 2012
I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
View 1 Replies
View Related
Mar 5, 2013
I have ordered RP2 and it will be having 8GB default memory. What is the difference between memory & Physical memory?Since I am able to see only 4GB memory in my ASR 1004. [code]
View 1 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Mar 12, 2013
I have a WLC with, let´s say, 30-40 AIR-LAP1142N-E-K9. Since last November the following issue happened 3 times. One of the APs (it´s always the same unit) remains online but both WiFi interfaces appear down. I´m unable to put it back UP like if they were disabled. Then i have to reboot the AP and it starts working again.
What could be happening? Should i open an RMA for this unit?
View 2 Replies
View Related
Aug 22, 2012
I've just bought an AIR-WLC2106-K9 and 3 x AIR-LAP1142N-E-K9 and I'm having a problem getting the AP's configured.
Firstly, the controller did not discover the device when it was on the same sub net, I had to plug it straight in which is no good for wireless-n due to the 100Mbps port speed on the controller. Secondly, when I am editing the AP through the controller webpage, none of the details are saved after applying changes (static IP etc).
I followed the Cisco quick start guide for the controller to get the basic config, radius server details etc in. It is running software version: 4.2.61.0
View 17 Replies
View Related
Sep 25, 2012
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies
View Related
May 2, 2012
We have a problem with AIR-LAP1142N access points.
AIR-LAP1142N-E-K9
Version 12.4(21a)JA
LAP's are not assotiated with controller yet. They get the ip address via dhcp, they are reachable by icmp.When I try to telnet, I get Password required, but none set? Is there any chance to get access to them without using serial port?
View 7 Replies
View Related
Feb 11, 2013
I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies
View Related
May 29, 2013
I'm in the process of trying to get a used LAP1142N access point connected to my already established WLAN. We currently have 7 active LAP1142N, our controller is a AIR-WLC2112-K9, and I am only trying to add one additional access point. I say this access point is used because we purchased it used, given it's not out of the box and hasn't ever been active in my environment. So far what I've tried is initially connecting the access point on to my network (powered over Ethernet) and consoled in from my desktop. With this, I was able to see the previous configuration so I ran a write erase/ reload. The AP shows a solid green light, but doesn't receive any configuration from the controller even when plugged directly in to the controller (on ports 7 and 8). I'm new to wireless, but familiar with Cisco CLI and web interfaces. I can't necessarily tell if this AP is set to autonomous as opposed to lightweight, but that could be the problem. Otherwise I'm lost. I've attached text files with the boot from CLI and show run from CLI.Let me know any additional information you may need. End note, I'm recieving DHCP (you can tell from boot), but it's not the same subnet as my controller or other active access points.
View 5 Replies
View Related
Apr 28, 2013
I have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
View 2 Replies
View Related
Apr 17, 2012
We have a set up which includes several air-lap1134n-e-k9 access points. We're having problems with a specific laptop connecting to the WLAN which is accessible via the AP. We can see numerous different SSIDs available and when we connect to either of the two we have set up it says it is unable to connect. One of the connections, let's call it Internet, has Layer 3 security set up. The other connection, Web, has Layer 2 security set up. The laptop can connect to neither. It can, however, connect to other wifi in the vacinity including a wifi hotspot we set up on an Android phone.
The laptop has an Intel Centrino Wireless-N 1030 network adapter with current drivers. The WLAN's we've set up, Internet and Web, are both enabled for 802.11n.
View 2 Replies
View Related
Apr 4, 2012
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies
View Related
Mar 9, 2013
Once I got LAP1142N from ebay and converted from Lightweight to Autonomous via TFTP but I see there is new IOS came out so it required to upgrade Bootloader which is c1140-boot-m.124-23c.JA1.bin and IOS is c1140-k9w7-tar.152-2.JB.Currently 1142N running IOS c1140-k9w7-tar.124-25d.JA and Bootloader Version 12.4(18a)JA.For while few hours ago I kept figuring it out how to upgrade bootloader on website but none of these will work.
View 8 Replies
View Related
Jun 4, 2012
1142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies
View Related
