Cisco Wireless :: AIR-WLC2106-K9 / AIR-LAP1142N-E-K9 - APS Configuration
Aug 22, 2012
I've just bought an AIR-WLC2106-K9 and 3 x AIR-LAP1142N-E-K9 and I'm having a problem getting the AP's configured.
Firstly, the controller did not discover the device when it was on the same sub net, I had to plug it straight in which is no good for wireless-n due to the 100Mbps port speed on the controller. Secondly, when I am editing the AP through the controller webpage, none of the details are saved after applying changes (static IP etc).
I followed the Cisco quick start guide for the controller to get the basic config, radius server details etc in. It is running software version: 4.2.61.0
View 17 Replies
ADVERTISEMENT
Dec 6, 2012
I am currently experiencing an issue with a WLC that I am trying to connect 3 new Access Points to of the type AIR-LAP1142N-E-K9 running Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 15.2(2)JA
I had the controller on firmware 7.0.220.0 and just upgraded to 7.3.101.0 in the hopes to solve my issue. The already connect APs running 12.4 was upgraded without any issues (apart from one - I'll get to that one) and it is now running as before. But the issue with the 3 new APs still persists. I have supplied a screenshot of the AP Join page.
Another issue that arose from the said upgrade was that a previously shutdown AP (of the same type and software version as the ones that upgraded perfectly) got turned on after the WLC firmware upgrade and is now not able to join the controller.
View 20 Replies
View Related
Nov 28, 2007
I am trying to get a controller to work on my network. output from the switch arp table.
Internet 172.28.227.2 0 001b.d5cf.79c0 ARPA Vlan103
Internet 172.28.227.1 - 001c.b1ad.7400 ARPA Vlan103
Internet 172.28.227.12 0 001d.a1cc.b7f8 ARPA Vlan103
controller config:
Interface Name................................... management
MAC Address...................................... 00:07:0e:25:ac:a0
IP Address....................................... 172.28.227.2
IP Netmask....................................... 255.255.255.0
[code]....
The switch see's it but i can not ping or access it via web or telnet.
View 5 Replies
View Related
Oct 3, 2012
we have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
View 1 Replies
View Related
Dec 11, 2012
I am about to configure a brand new AIR-WLC2106-K9 V05 and didn't manage to find what is the deafult IP address configured on the device. I need it so I could start Web GUI management session.
View 4 Replies
View Related
Mar 2, 2013
I have a WLC2106 and AP3502i. The issue that I am having is the radio for 5GHz is not showing up in "Wireless > 802.11a/n" (see attached screenshot) I am not exactly sure what was the problem. When I went to 802.11b/g/n I do see an entry for 2.4Ghz radio, but nothing on 5GHz.
I have the AP plugged directly to my 3550POE, and when I used the command "show power inline" it says that the switch is providing 15.4W and there is still 345W remaining on the switch. The LED on the AP is solid green. I issued a no shutdown on dot11radio1 and the status is up/up, but there is still no entry under "Wireless > 802.11a/n"
View 23 Replies
View Related
Feb 15, 2013
I have a WLC 2106 which is configured and working as follows: [code] how do i get the AP at Site B to use the local server (10.0.28.x) to hand out DHCP leases?
View 3 Replies
View Related
Jun 13, 2010
I am getting error messages for clients:
11 Mon Jun 14 09:11:56 2010 Decrypt errors occurred for client 00:13:ce:54:57:3c using WPA key on 802.11b/g interface of AP 00:16:9c:91:97:c0 12 Mon Jun 14 09:11:56 2010 Decrypt errors occurred for client 00:16:6f:91:d8:60 using WPA2 key on 802.11b/g interface of AP 00:16:9c:91:97:c0
These are only occuring for clients that are disconnecting....
They can reconnect after a WLC reboot....
We have swapped APs.....
I have seen this error in other forums but it says not to worry about it. There has to be a connection between this and clients getting disconnected. We have anywhere between 10-50 clients on the system at any one time.Is this a client issue (nic firmware, version) or is this an error in the controller??
AIR-WLC2106-K9
IOS ver: 6.0.196.0
View 4 Replies
View Related
Feb 18, 2013
I get the following error whne enabling 802.11a network on a AIR-WLC2106-K9. Country is set to ID (Indonesia),>config 802.11a enable network802.11a network not supported for this Country CodeYet, on a AIR-CT2504-K9, set to same country code there is no problem. Is this a WLC model or version issue? WLC2106 is on version 6.0.199.4 while the CT2504 is 7.0.220.0
View 3 Replies
View Related
Apr 26, 2013
I am in the process of building a small educational lab. I just want to make sure that I am not going to have any AP registration/join issues due to regulatory compatibility with a AIR-WLC2106-K9 controller and a AIR-LAT1142N-N-K9 access point. Will this work and if so, will I then be in the clear as far as having devices like my computer and phone attach to the SSID?
View 5 Replies
View Related
Mar 13, 2012
I bought 6 air-lap1042n-a-k9 for our business. They are mounted. I bought a Cisco POE switch for them. I hooked them up and realized they needed a Wireless LAN Controller. I have never dealt with these before. From my research, I need to buy AIR-WLC2106-K9.Can I just connect my POE switch to the LAN Controller to configure all 6 access points that are connected to the POE switch?
View 6 Replies
View Related
Mar 12, 2013
I have a WLC with, let´s say, 30-40 AIR-LAP1142N-E-K9. Since last November the following issue happened 3 times. One of the APs (it´s always the same unit) remains online but both WiFi interfaces appear down. I´m unable to put it back UP like if they were disabled. Then i have to reboot the AP and it starts working again.
What could be happening? Should i open an RMA for this unit?
View 2 Replies
View Related
Sep 25, 2012
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies
View Related
May 2, 2012
We have a problem with AIR-LAP1142N access points.
AIR-LAP1142N-E-K9
Version 12.4(21a)JA
LAP's are not assotiated with controller yet. They get the ip address via dhcp, they are reachable by icmp.When I try to telnet, I get Password required, but none set? Is there any chance to get access to them without using serial port?
View 7 Replies
View Related
Feb 11, 2013
I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies
View Related
May 29, 2013
I'm in the process of trying to get a used LAP1142N access point connected to my already established WLAN. We currently have 7 active LAP1142N, our controller is a AIR-WLC2112-K9, and I am only trying to add one additional access point. I say this access point is used because we purchased it used, given it's not out of the box and hasn't ever been active in my environment. So far what I've tried is initially connecting the access point on to my network (powered over Ethernet) and consoled in from my desktop. With this, I was able to see the previous configuration so I ran a write erase/ reload. The AP shows a solid green light, but doesn't receive any configuration from the controller even when plugged directly in to the controller (on ports 7 and 8). I'm new to wireless, but familiar with Cisco CLI and web interfaces. I can't necessarily tell if this AP is set to autonomous as opposed to lightweight, but that could be the problem. Otherwise I'm lost. I've attached text files with the boot from CLI and show run from CLI.Let me know any additional information you may need. End note, I'm recieving DHCP (you can tell from boot), but it's not the same subnet as my controller or other active access points.
View 5 Replies
View Related
Apr 28, 2013
I have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
View 2 Replies
View Related
Apr 17, 2012
We have a set up which includes several air-lap1134n-e-k9 access points. We're having problems with a specific laptop connecting to the WLAN which is accessible via the AP. We can see numerous different SSIDs available and when we connect to either of the two we have set up it says it is unable to connect. One of the connections, let's call it Internet, has Layer 3 security set up. The other connection, Web, has Layer 2 security set up. The laptop can connect to neither. It can, however, connect to other wifi in the vacinity including a wifi hotspot we set up on an Android phone.
The laptop has an Intel Centrino Wireless-N 1030 network adapter with current drivers. The WLAN's we've set up, Internet and Web, are both enabled for 802.11n.
View 2 Replies
View Related
Apr 4, 2012
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies
View Related
Feb 17, 2011
I have been trying to get Airprint to work in our network. Topology is a 255.255.255.254.x network that has mostly wired with wireless all under the same subnet. Airprint will not discover printers if on the WLC2106 WiFi network but if the iPad or iPhone is connected to some small Linksys WiFi router, it works.
What should be enabled or disabled on the WLC2106 to get Airprint to work?
View 28 Replies
View Related
Mar 9, 2013
Once I got LAP1142N from ebay and converted from Lightweight to Autonomous via TFTP but I see there is new IOS came out so it required to upgrade Bootloader which is c1140-boot-m.124-23c.JA1.bin and IOS is c1140-k9w7-tar.152-2.JB.Currently 1142N running IOS c1140-k9w7-tar.124-25d.JA and Bootloader Version 12.4(18a)JA.For while few hours ago I kept figuring it out how to upgrade bootloader on website but none of these will work.
View 8 Replies
View Related
Jun 4, 2012
1142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies
View Related
Apr 11, 2012
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
View 27 Replies
View Related
Nov 14, 2012
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
View 8 Replies
View Related
Feb 12, 2013
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
View 2 Replies
View Related
Sep 3, 2012
I would like to update the firmware of this AP but I'm having problems. The commands seems to be not complete
APa493.4c46.8e83#?
Exec commands:
cd Change current directory
clear Reset functions
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
enable Turn on privileged commands
exit Exit from the EXEC (code)
View 2 Replies
View Related
Feb 7, 2013
I have two AP models in my network. LAP1142N-A-K9 and LAP1142N-N-K9. The LAP1142N-A works fine with both radios (a/n and b/g/n), but the LAP1142N-N is getting a regulatory domain not supported problem with the 802.11a/n radio, which is keeping it in the down state. I'm in Canada, and my country code on my 5508 WLCs are set to CA. My WLCs are running firmware version 6.0. I read over some specs and the difference between the two APs is FCC cfg vs Non-FCC cfg... Not 100% sure what that means.
View 13 Replies
View Related
Sep 18, 2012
our customer in France, it deploy access points AIR-LAP1142K-E-K9 in france but also in morocco.from Cisco's documentation and Azlan, it is not possible to purchase AP AIR-LAP1142K-E-K9 to the customer in Morocco. but it's possible only the item AIR-LAP1142K-I-K9.We have an issue: the WLC (version 7-0-220-0) is in france country code (FR) and regulatory domain (-E) and APs are in morocco.the regulatory domain (-I) is not supported in country (FR ), the interface 802.11a is not supported.
1/ is it possible to activate 802.11a on AIR-LAP1142K-I-K9 ? how can it be done ?
2/ or we must make an exchange AIR-LAP1142K-I-K9 by AIR-LAP1142K-E-K9 ?
3/ the morocco's customer said that it's possible to purchase AIR-LAP1142K-E-K9. is it true ? on the website Cisco: url... for morocco: the customer, can it purchase AIR-LAP1142K-E-K9 ?
View 2 Replies
View Related
Jan 24, 2013
I have downgraded one of our AP1142N-E K9 to Autonomous mode with this image: c1140-k9w7-tar.152-2.JB.tar I have uses cisco's instructions.
After successfull installation, I can open the Webinterface, but it shows almost no information. Only Device Type end serialnumber, but nothing more. Also it is not possible to save any configuration.
Alternatively I have installed:
c1140-k9w7-tar.124-21a.JA1.tar
Same problem. I have tried it with a LAP1252N later. Same problem.
View 2 Replies
View Related
Feb 5, 2013
I have 19 locations, each with 1 or more LAP1142N AP's in FlexConnect mode, AP's are primed using CAPWAP to my 5508 WLC at the datacenter. The AP's join the WLC without issue every time. I have two WLAN's, one guest and one staff, the guest network is open and obtains DHCP from a WatchGuard XTM33 firewall at each of the remote locations. The staff side is WPA2/RADIUS and DHCP is assigned from the WLC. Each AP is assigned a static IP that is not in the DHCP scope. For example: DHCP scope on the branch firewall is 192.168.1.10-250 the AP will be assigned static IP of 192.168.1.1.. The AP's are connected to a HP procurve switch that has a untagged VLAN, the firewall is using the native vlan 1 and so is the AP.
I have been running this network for over a year and it has not had a single issue until the last two weeks. Nothing on the network has changed or has been upgraded.The issue I am seeing is that clients are no longer able to connect to the AP and do not get DHCP assigned to them. I am able to get it working, if I remove the static IP from the AP, the AP will reboot, join the controller, then begin working, users can connect and DHCP is assigned from the firewall as it should. However, If the AP then reboots, the AP will join back to the controller but no clients can connect nor do they get a DHCP address. So, I then reassign a static IP to the AP again and it reboots, connects to the controller and clients then can connect and get DHCP.i've found several posts on this topic, in fact the patch of unassigning or reassigning static IP is one that I found. I am also waiting on my SmartNet to start up and will be contacting Cisco support as well.
View 15 Replies
View Related
Feb 25, 2012
how to downgrade/upgrade AIR-LAP1142N-N-K9 access point to autonomous mode, because i don't have controller. i'm not able to login to access point as its in Leightweight mode.
View 4 Replies
View Related
Nov 1, 2011
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
View 7 Replies
View Related
Feb 7, 2012
We have a strange problem. We have a WCS v.7.0.172 that controls our two WLC v.7.0.116 and we have also two "Anchor Controller" WLC
v.7.0.116 for Guest Access.
We use the LAP1142N and every AP has two SSID's. One for internal data traffic and the other one for the guests.
Now the problem is, that even if we have internal and external user on the same AP, the guest users gets disconnected after a few time. Sometimes after 20 minutes, sometimes after 90 minutes...but the user is still working. It's really irregular.
View 2 Replies
View Related
