Cisco Wireless :: AIR LAP1142N Regulatory Domain With WLC2100 (FR)
Sep 18, 2012
our customer in France, it deploy access points AIR-LAP1142K-E-K9 in france but also in morocco.from Cisco's documentation and Azlan, it is not possible to purchase AP AIR-LAP1142K-E-K9 to the customer in Morocco. but it's possible only the item AIR-LAP1142K-I-K9.We have an issue: the WLC (version 7-0-220-0) is in france country code (FR) and regulatory domain (-E) and APs are in morocco.the regulatory domain (-I) is not supported in country (FR ), the interface 802.11a is not supported.
1/ is it possible to activate 802.11a on AIR-LAP1142K-I-K9 ? how can it be done ?
2/ or we must make an exchange AIR-LAP1142K-I-K9 by AIR-LAP1142K-E-K9 ?
3/ the morocco's customer said that it's possible to purchase AIR-LAP1142K-E-K9. is it true ? on the website Cisco: url... for morocco: the customer, can it purchase AIR-LAP1142K-E-K9 ?
View 2 Replies
ADVERTISEMENT
Feb 7, 2013
I have two AP models in my network. LAP1142N-A-K9 and LAP1142N-N-K9. The LAP1142N-A works fine with both radios (a/n and b/g/n), but the LAP1142N-N is getting a regulatory domain not supported problem with the 802.11a/n radio, which is keeping it in the down state. I'm in Canada, and my country code on my 5508 WLCs are set to CA. My WLCs are running firmware version 6.0. I read over some specs and the difference between the two APs is FCC cfg vs Non-FCC cfg... Not 100% sure what that means.
View 13 Replies
View Related
Mar 22, 2012
I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
View 12 Replies
View Related
Mar 24, 2013
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
View 2 Replies
View Related
Apr 26, 2013
I am in the process of building a small educational lab. I just want to make sure that I am not going to have any AP registration/join issues due to regulatory compatibility with a AIR-WLC2106-K9 controller and a AIR-LAT1142N-N-K9 access point. Will this work and if so, will I then be in the clear as far as having devices like my computer and phone attach to the SSID?
View 5 Replies
View Related
May 7, 2012
it's possible to implement that on any Cisco Wireless Devices, so All I need is create one wireless account with timer for 1 hour, so SSID as guest without any password and once you connected it works only for 1 hour then disconnects and you can't connect again. Then create second account where you can browse timelessly but you need a password to connect there.
1. Is it possible to do that using one or two SSID, or password changes?
2. Is it possible to do that on Wireless controller WLC2100 series, or AP1000, AP1100 series, or AP500 series?
View 7 Replies
View Related
Jan 19, 2011
Due to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
View 8 Replies
View Related
Jan 20, 2011
I've got a 2106 that I'm installing for a customer and having issues with it assigning DHCP to WiFI clients. What's odd is that this was working at one point at home during testing. Only difference at this point is LAN hardware at the customer location.
Simple config- single flat vlan on Cat2960G switch, ASA5505 serving up DHCP for the network. Wired clients are receiving DHCP fine.
Mgmt IP192.168.0.10/24Mgmt Gateway192.168.0.1Mgmt VLAN0Mgmt Int port1Mgmt DHCP server192.168.0.1AP Mgr Int IP192.168.0.11Virtual GW IP1.1.1.1RF group namerfgrp1SSIDxxxxClient Static IP?noCountry Code802.11a/b/g statusenabledRadio resource mgmt statusenabled I've run dhcpd debug on both the controller and the ASA and I see the DHCPD requests on the controller, but I never see them hitting the ASA.
I don't have the specific version of code it's running, but I know it's 6.0. One of my local Cisco account engineers found some Cisco CSC bugs referencing this issue. One TAC cas even referenced stripping all security off the WiFi, connecting the client and then reimplementing the security again.
View 7 Replies
View Related
Mar 12, 2013
I have a WLC with, let´s say, 30-40 AIR-LAP1142N-E-K9. Since last November the following issue happened 3 times. One of the APs (it´s always the same unit) remains online but both WiFi interfaces appear down. I´m unable to put it back UP like if they were disabled. Then i have to reboot the AP and it starts working again.
What could be happening? Should i open an RMA for this unit?
View 2 Replies
View Related
Aug 22, 2012
I've just bought an AIR-WLC2106-K9 and 3 x AIR-LAP1142N-E-K9 and I'm having a problem getting the AP's configured.
Firstly, the controller did not discover the device when it was on the same sub net, I had to plug it straight in which is no good for wireless-n due to the 100Mbps port speed on the controller. Secondly, when I am editing the AP through the controller webpage, none of the details are saved after applying changes (static IP etc).
I followed the Cisco quick start guide for the controller to get the basic config, radius server details etc in. It is running software version: 4.2.61.0
View 17 Replies
View Related
Sep 25, 2012
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies
View Related
May 2, 2012
We have a problem with AIR-LAP1142N access points.
AIR-LAP1142N-E-K9
Version 12.4(21a)JA
LAP's are not assotiated with controller yet. They get the ip address via dhcp, they are reachable by icmp.When I try to telnet, I get Password required, but none set? Is there any chance to get access to them without using serial port?
View 7 Replies
View Related
Feb 11, 2013
I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies
View Related
May 29, 2013
I'm in the process of trying to get a used LAP1142N access point connected to my already established WLAN. We currently have 7 active LAP1142N, our controller is a AIR-WLC2112-K9, and I am only trying to add one additional access point. I say this access point is used because we purchased it used, given it's not out of the box and hasn't ever been active in my environment. So far what I've tried is initially connecting the access point on to my network (powered over Ethernet) and consoled in from my desktop. With this, I was able to see the previous configuration so I ran a write erase/ reload. The AP shows a solid green light, but doesn't receive any configuration from the controller even when plugged directly in to the controller (on ports 7 and 8). I'm new to wireless, but familiar with Cisco CLI and web interfaces. I can't necessarily tell if this AP is set to autonomous as opposed to lightweight, but that could be the problem. Otherwise I'm lost. I've attached text files with the boot from CLI and show run from CLI.Let me know any additional information you may need. End note, I'm recieving DHCP (you can tell from boot), but it's not the same subnet as my controller or other active access points.
View 5 Replies
View Related
Apr 28, 2013
I have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
View 2 Replies
View Related
Apr 17, 2012
We have a set up which includes several air-lap1134n-e-k9 access points. We're having problems with a specific laptop connecting to the WLAN which is accessible via the AP. We can see numerous different SSIDs available and when we connect to either of the two we have set up it says it is unable to connect. One of the connections, let's call it Internet, has Layer 3 security set up. The other connection, Web, has Layer 2 security set up. The laptop can connect to neither. It can, however, connect to other wifi in the vacinity including a wifi hotspot we set up on an Android phone.
The laptop has an Intel Centrino Wireless-N 1030 network adapter with current drivers. The WLAN's we've set up, Internet and Web, are both enabled for 802.11n.
View 2 Replies
View Related
Apr 4, 2012
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies
View Related
Mar 9, 2013
Once I got LAP1142N from ebay and converted from Lightweight to Autonomous via TFTP but I see there is new IOS came out so it required to upgrade Bootloader which is c1140-boot-m.124-23c.JA1.bin and IOS is c1140-k9w7-tar.152-2.JB.Currently 1142N running IOS c1140-k9w7-tar.124-25d.JA and Bootloader Version 12.4(18a)JA.For while few hours ago I kept figuring it out how to upgrade bootloader on website but none of these will work.
View 8 Replies
View Related
Jun 4, 2012
1142N-E0K9 will support both 2.4 and 5 ghz or only 2.4 .
View 4 Replies
View Related
Apr 11, 2012
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
View 27 Replies
View Related
Nov 14, 2012
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
View 8 Replies
View Related
Feb 12, 2013
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
View 2 Replies
View Related
Sep 3, 2012
I would like to update the firmware of this AP but I'm having problems. The commands seems to be not complete
APa493.4c46.8e83#?
Exec commands:
cd Change current directory
clear Reset functions
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
enable Turn on privileged commands
exit Exit from the EXEC (code)
View 2 Replies
View Related
Dec 6, 2012
I am currently experiencing an issue with a WLC that I am trying to connect 3 new Access Points to of the type AIR-LAP1142N-E-K9 running Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 15.2(2)JA
I had the controller on firmware 7.0.220.0 and just upgraded to 7.3.101.0 in the hopes to solve my issue. The already connect APs running 12.4 was upgraded without any issues (apart from one - I'll get to that one) and it is now running as before. But the issue with the 3 new APs still persists. I have supplied a screenshot of the AP Join page.
Another issue that arose from the said upgrade was that a previously shutdown AP (of the same type and software version as the ones that upgraded perfectly) got turned on after the WLC firmware upgrade and is now not able to join the controller.
View 20 Replies
View Related
Jan 24, 2013
I have downgraded one of our AP1142N-E K9 to Autonomous mode with this image: c1140-k9w7-tar.152-2.JB.tar I have uses cisco's instructions.
After successfull installation, I can open the Webinterface, but it shows almost no information. Only Device Type end serialnumber, but nothing more. Also it is not possible to save any configuration.
Alternatively I have installed:
c1140-k9w7-tar.124-21a.JA1.tar
Same problem. I have tried it with a LAP1252N later. Same problem.
View 2 Replies
View Related
Feb 5, 2013
I have 19 locations, each with 1 or more LAP1142N AP's in FlexConnect mode, AP's are primed using CAPWAP to my 5508 WLC at the datacenter. The AP's join the WLC without issue every time. I have two WLAN's, one guest and one staff, the guest network is open and obtains DHCP from a WatchGuard XTM33 firewall at each of the remote locations. The staff side is WPA2/RADIUS and DHCP is assigned from the WLC. Each AP is assigned a static IP that is not in the DHCP scope. For example: DHCP scope on the branch firewall is 192.168.1.10-250 the AP will be assigned static IP of 192.168.1.1.. The AP's are connected to a HP procurve switch that has a untagged VLAN, the firewall is using the native vlan 1 and so is the AP.
I have been running this network for over a year and it has not had a single issue until the last two weeks. Nothing on the network has changed or has been upgraded.The issue I am seeing is that clients are no longer able to connect to the AP and do not get DHCP assigned to them. I am able to get it working, if I remove the static IP from the AP, the AP will reboot, join the controller, then begin working, users can connect and DHCP is assigned from the firewall as it should. However, If the AP then reboots, the AP will join back to the controller but no clients can connect nor do they get a DHCP address. So, I then reassign a static IP to the AP again and it reboots, connects to the controller and clients then can connect and get DHCP.i've found several posts on this topic, in fact the patch of unassigning or reassigning static IP is one that I found. I am also waiting on my SmartNet to start up and will be contacting Cisco support as well.
View 15 Replies
View Related
Feb 25, 2012
how to downgrade/upgrade AIR-LAP1142N-N-K9 access point to autonomous mode, because i don't have controller. i'm not able to login to access point as its in Leightweight mode.
View 4 Replies
View Related
Nov 1, 2011
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
View 7 Replies
View Related
Feb 7, 2012
We have a strange problem. We have a WCS v.7.0.172 that controls our two WLC v.7.0.116 and we have also two "Anchor Controller" WLC
v.7.0.116 for Guest Access.
We use the LAP1142N and every AP has two SSID's. One for internal data traffic and the other one for the guests.
Now the problem is, that even if we have internal and external user on the same AP, the guest users gets disconnected after a few time. Sometimes after 20 minutes, sometimes after 90 minutes...but the user is still working. It's really irregular.
View 2 Replies
View Related
Mar 29, 2012
I have trouble accessing the internet from my laptop after installing Ciso AIR-LAP1142N-A-K9 AP.The AP are connetected to my router (which has a DHCP enabled) via a switch and each has a Fix IP address with network mask, gateway and DNS already configured. When I triy to connect to the access point, only the IP address and network mask are automatically assigned to the my laptop. and I have to manually input the gatway and DNS to be able to navigate the internet. I would like to know which configuration will allow any node that tries to connect the internet via the access point to be automatically configured to access the internet after authentication.
View 4 Replies
View Related
Mar 18, 2012
I can run the Cisco AIR-LAP1142n-a-k9 access point in standalone mode? I don't want it to look for a controller when it boots up.
View 3 Replies
View Related
Nov 13, 2011
I have a WLC of 4402 and AP's of AIR-LAP1142N-E-K9 . Where am getting problem of that users are complaining that they cannot connect it some times and they used to get disconnected in between.
View 1 Replies
View Related
Mar 7, 2012
We have an autonomous AIR-LAP1142N-E-K9 AP with software release version 12.4(25d)JA1. The access point is configured and an SSID is broadcasted. However when users are trying to connect to the AP, authentication seems to be accepted but users are not connected. I suspected the issue in DHCP but even on static IP the user is not connected.I dont believe any LAN issue is there cause I connected a PC to the same interface where the AP is connected and it took an IP from the required VLAN (1234) [code]
View 3 Replies
View Related
