Cisco Wireless :: AIR-CAP3502I-N-K9 - Change Regulatory Domain On Lightweight Access Point?
Mar 22, 2012
I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
View 12 Replies
ADVERTISEMENT
Apr 26, 2013
I am in the process of building a small educational lab. I just want to make sure that I am not going to have any AP registration/join issues due to regulatory compatibility with a AIR-WLC2106-K9 controller and a AIR-LAT1142N-N-K9 access point. Will this work and if so, will I then be in the clear as far as having devices like my computer and phone attach to the SSID?
View 5 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Feb 7, 2013
I have two AP models in my network. LAP1142N-A-K9 and LAP1142N-N-K9. The LAP1142N-A works fine with both radios (a/n and b/g/n), but the LAP1142N-N is getting a regulatory domain not supported problem with the 802.11a/n radio, which is keeping it in the down state. I'm in Canada, and my country code on my 5508 WLCs are set to CA. My WLCs are running firmware version 6.0. I read over some specs and the difference between the two APs is FCC cfg vs Non-FCC cfg... Not 100% sure what that means.
View 13 Replies
View Related
Sep 18, 2012
our customer in France, it deploy access points AIR-LAP1142K-E-K9 in france but also in morocco.from Cisco's documentation and Azlan, it is not possible to purchase AP AIR-LAP1142K-E-K9 to the customer in Morocco. but it's possible only the item AIR-LAP1142K-I-K9.We have an issue: the WLC (version 7-0-220-0) is in france country code (FR) and regulatory domain (-E) and APs are in morocco.the regulatory domain (-I) is not supported in country (FR ), the interface 802.11a is not supported.
1/ is it possible to activate 802.11a on AIR-LAP1142K-I-K9 ? how can it be done ?
2/ or we must make an exchange AIR-LAP1142K-I-K9 by AIR-LAP1142K-E-K9 ?
3/ the morocco's customer said that it's possible to purchase AIR-LAP1142K-E-K9. is it true ? on the website Cisco: url... for morocco: the customer, can it purchase AIR-LAP1142K-E-K9 ?
View 2 Replies
View Related
Apr 4, 2012
Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies
View Related
Jan 13, 2013
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies
View Related
Apr 24, 2011
how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
View 6 Replies
View Related
Jul 29, 2012
Is possible to configure a Lightweight Access Point LAP1242AG as 802.1x supplicant using Microsoft NPS radius server that not use EAP-FAST authentication method? Can I use PEAP in NPS radius?
View 6 Replies
View Related
Apr 24, 2013
We have a remote site with ~5 users, 4 IP phones and a network printer. Right now we have an old Win2003 box serving as the DC for that site. It is connected back to us via 10MB layer 3 routing on a HP 5500G-EL switch. This windows server is getting quite old and I'd like to avoid the expense of buying a new server just to hand out addresses and authenticate users. How do you all handle login authentication,dns,and DHCP for your lightweight remotes sites?
View 11 Replies
View Related
Jan 24, 2011
I set up an older WAP54-G v1.1, it would not work effectively on the network, so I checked and its firmware had never been updated ( still using v 1.09) I updated it to the newest firmware today. It worked better and finally would accept changes in the SSID field. I changed and it immediatly accepted and started to broadcast appropriately, as I was planning to put a few more of these up around the school I changed its IP to 192,168,1,246 it immediatly crashed and would not allow me to see it on the browser. After sometime I simply reset it and reconfigured it again. Now it has changed in the SSID field but when a wireless device reads it the ntwork is note detected, however an open linksys system is. you can join it and go to the internet, but not the network.
Sometimes it lets me see controls and other times not, when it does not work, powering cycling it seems to make it is able to be seen.
View 1 Replies
View Related
Feb 24, 2012
how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 Replies
View Related
Oct 9, 2011
When I change my WRT320N routers IP address to use it as an access point only and bring it in the IP range of my ccombined modem/router I'm not able to view the setup page via the new IP address. I have tried to change the IP from the default 192.168.1.1 to 192.168.178.2. After changing and applying the changes I restarted the router and tried to access the router via the new address. This was not possible am I doing something wrong or did I forgot something?
View 8 Replies
View Related
Dec 30, 2012
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies
View Related
Apr 1, 2012
I brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
View 5 Replies
View Related
Jul 11, 2012
I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
View 4 Replies
View Related
Jul 5, 2012
How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access
View 1 Replies
View Related
Mar 22, 2012
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies
View Related
May 4, 2010
I try to change the wmm settings to video, but it's always going back to background settings after saving.I already re-uploaded the firmware, but with no result...I noticed that is a newer firmware available for the WET610n where they solved this issue, but they haven't changed it for the WAP610n....
View 9 Replies
View Related
Jun 16, 2012
I have a new WAP54G Access point in our network. I would like to change WPA security settings, but am not able to do it.I have done everything as installation leaflet says, and I get to the 5th point Status sheet: Firmware version v.304, MAC address (numbers), IP address 192.168.1.245, SSID linksys, Channel channel 6 and WEB security Disable
What I would like to do, is change SSID and have WPA2 security. When I am clicking "Yes", it goes to the next sheet "Password", I write admin and click "Enter". I will have Pop-up window "Setup Access violation at address 0049BDB6 in module 'Setup.exe'. Write of address C933016A."
View 2 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Jun 6, 2013
I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies
View Related
Mar 14, 2013
I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies
View Related
Nov 29, 2011
My problem is everytime i go to dublin i have to change domain and ip for that lacation for local work, sometime its really pain to change back to our own domain whenever i come back to northern ireland office for connecting LAN.clicking can change different domain and ip for different location.
View 1 Replies
View Related
Nov 13, 2012
I have just change the DNS domain name of my ISE from CLI and restarted the appliance (its a 3395 appliance)However,, when i log in via GUI it doesnt reflect the new dns name.
View 1 Replies
View Related
Jul 25, 2011
Is it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies
View Related
Sep 21, 2011
This summer the IT department at my location rolled out a little more than 100 AIR-CAP3502I-A-K9's to much success. We have had an issue with only one AP. This paticular AP must have gotten unplugged during the updating process after the initial conneciton to the controller was made as the LED currently blinks red-blue-red, indicating an error in the flash memory according to the manual.
View 2 Replies
View Related
Dec 14, 2011
We've just replaced some 1240 LAPs with 20 x 3502i.
Seem to have a problem, most of the 14 * 3502i have regersted on the network and working, 6 arent connecting and log below. I've replaced one of the AP with a differnt one, same model and batch and this works.
WISMs on 7.0.98.0
Scirpt
*Mar 1 00:15:16.015: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
View 11 Replies
View Related
Nov 23, 2011
I was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies
View Related
May 8, 2013
We are setting up one of these for the first time. It is in a constant rebooting process.
Here is the boot process:
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
[Code].....
View 3 Replies
View Related
Dec 9, 2012
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
View 1 Replies
View Related
Oct 18, 2012
I have 1 cisco AP (CAP3502I) which is not able to associate with WLC (version 7.0.235.0), using CAPWAP. Simply from debug I can see that AP is trying to contact WLC on port udp/5246 but can't see any response from WLC.
*Oct 19 07:06:50.055: UDP: sent src=x.x.x.x(4271), dst=wlc.wlc.wlc.wcl(5246), length=47
AP is getting config about WLC from DHCP option 43 and have own reservation to get same IP address (+default GW). AP is NOT associated but as it has IP address from DHCP then it is pingable. But don't know why, but I'm not able to tracert/traceroute to this AP, as I can see it is getting packets but it is not responding.
But on different locations, where are same APs model (associated with WLC) I have no problem with traceroute it, as APs are responding.
My question: It is not related that AP is not able to associate with WLC (still working on it) BUT should I be able to traceroute/tracert to unassociated AP (to his IP) and get response???
NOTE:
==> WLC is in DC and AP on one location, so diagram could be: WLC ---- L3 device ---- Provider MPLS router..........Provider MPLS router ---- L3 device -- L2 switch --- AP (CAPWAP)
@It means that there is NO FW on tha way :-)
I check many other APs with same model and non of them has problem to respond for traceroute, but this particular unassociated one has :-
View 3 Replies
View Related
