Linksys Access Point :: Cannot Change Channel On WAP45 - Unidentified / No Access?
Jul 5, 2012How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access
View 1 Replies
ADVERTISEMENT
Linksys Access Point :: How To Enable Channel 13 On WET54g
Jun 30, 2012I am using it in Europe and need to enable channel 13 so I can connect to a network on this channel. I vaguely remember being told this was done by accessing a hidden setup page. how to enable channel 13 on a WET54g V3.1?
View 9 Replies View RelatedLinksys Access Point :: WAP610n Can't Change Wmm Settings
May 4, 2010I try to change the wmm settings to video, but it's always going back to background settings after saving.I already re-uploaded the firmware, but with no result...I noticed that is a newer firmware available for the WET610n where they solved this issue, but they haven't changed it for the WAP610n....
View 9 Replies View RelatedLinksys Access Point :: WAP54G - Change WPA Security Settings?
Jun 16, 2012I have a new WAP54G Access point in our network. I would like to change WPA security settings, but am not able to do it.I have done everything as installation leaflet says, and I get to the 5th point Status sheet: Firmware version v.304, MAC address (numbers), IP address 192.168.1.245, SSID linksys, Channel channel 6 and WEB security Disable
What I would like to do, is change SSID and have WPA2 security. When I am clicking "Yes", it goes to the next sheet "Password", I write admin and click "Enter". I will have Pop-up window "Setup Access violation at address 0049BDB6 in module 'Setup.exe'. Write of address C933016A."
Linksys Wireless Router :: Change E3200 To Access Point?
Feb 24, 2012how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 Replies View RelatedLinksys Wireless Router :: Change WRT320N IP Address To Use It As An Access Point?
Oct 9, 2011When I change my WRT320N routers IP address to use it as an access point only and bring it in the IP range of my ccombined modem/router I'm not able to view the setup page via the new IP address. I have tried to change the IP from the default 192.168.1.1 to 192.168.178.2. After changing and applying the changes I restarted the router and tried to access the router via the new address. This was not possible am I doing something wrong or did I forgot something?
View 8 Replies View RelatedBelkin Routers :: Configure N300 As Access Point - Unidentified Network?
Nov 9, 2012As per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
Broadband :: Router / Access Point Channel Conflict?
Mar 23, 2011How do I improve my Wireless Network Environment
View 2 Replies View RelatedCisco Wireless :: 1140 Access Point Channel Deployment
Apr 12, 2012We are starting to greatly increase our access point density throughout our floors and I am wondering if we are using the correct channel assignments. We are using LAP 1140's and 3500's. We have some locations that have have anywhere from 4 to 9 floors in one location. These are consecutive floors that have 8 to 11 APs per floor. There are also other businesses in these buildings that use wireless as well. We use 802.11a/n and 802.11b/g/n. Right now the channels are set to the default, (36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161 for 802.11a) and (1, 6, 11 for 802.11b/g/n). I was wondering that since we are increasing our density whether we should enable other 802.11b/g/n channels outside of 1,6,11. I know the other channels can overlap but with correct placement I am wondering if it would improve our wireless coverage since we wouldn't have 8 to 11 APs fighting for only 3 channels. Any experience with enabling other 802.11b/g/n channels?
View 11 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Linksys Access Point :: WAP54G Access Point Setup After A Reset?
Jul 9, 2006I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedLinksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point
Jan 17, 2013I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedLinksys Access Point :: WRT320N Access Point Vs Range Extender
Dec 14, 2011Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedLinksys Access Point :: WAP4410n MIBs Or OIDs For Access Point
Jul 3, 2012I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Linksys Access Point :: Cannot Access Configuration Page For WAP11 Access
Jun 12, 2007Cannot access configuration page for WAP11 Access
View 9 Replies View RelatedLinksys Access Point :: Repeat WAP54G Access Point?
Aug 25, 2011What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedLinksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Linksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedLinksys Access Point :: E3000 Configuration As Access Point?
Apr 6, 2011I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedLinksys Access Point :: Way To Find Mib For WAP54G Access Point?
Feb 10, 2012I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedCisco :: Change WPA2 Key On Aironet 1231g Access Point?
Mar 22, 2012I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedLinksys Wireless Router :: E1200 - Access Restrictions Change To Access Policy?
Feb 25, 2013What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedLinksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?
Nov 24, 2011I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.
View 3 Replies View RelatedCisco Wireless :: AIR-CAP3502I-N-K9 - Change Regulatory Domain On Lightweight Access Point?
Mar 22, 2012I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
Cisco Wireless :: Change IP Address Of Aironet 1200 Series Access Point
Dec 30, 2012we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedCisco Wireless :: LAP1131AG - Change Firmware To Make Normal Access Point
Apr 1, 2012I brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
View 5 Replies View RelatedLinksys Access Point :: Access Guest Account Through WAP54G?
Jun 9, 2011My network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies View RelatedLinksys Access Point :: Can't Access WAP54G After Firmware Upgrade
Apr 30, 2012I just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedLinksys Access Point :: WAP 4400N Unable To Access AP?
Jan 14, 2012I am not able to access my wireless access point anymore. I tried to access the web configuration in my browser as I have in the past 192.168.1.245, but I have no luck there. I tried to reset it by holding the reset button for 10-30 seconds, and I have no luck with that. What I have noticed on the AP is that the ethernet light keeps going out. The only light that is lit on my AP is the power and sometimes the ethernet light. My AP is connected to my router which I am able to gain access to the internet from any devices connected to the router except the AP. I have a router (E2000), a WAP4400N, and switch. I want to keep my wireless access separate from my business network. I cannot get my WAP4400N to work anymore.
View 1 Replies View RelatedLinksys Access Point :: Remotely Access A WAP54G?
Feb 15, 2011I would like to ask if its possible to remotely access a WAP54G?
View 3 Replies View RelatedLinksys Access Point :: Wap54g - How To Access Web Interference
Mar 1, 2007my wap54g is not working even i hold reset butoon for 60 second it not woring even my linksys wap54g reset button is not work for reset it, It not do any thing and still i cant accest is web interference
View 9 Replies View Related
