how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 RepliesWe're trying to connect our Linksys E3200 via ethernet wire to an existing company network that already has a router and switch - it will simply be connected to a port on our switch, and needs to function as an access point only (no DHCP, no routing, no NAT, etc.).
View 3 Replies View RelatedI am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies View RelatedWhen I change my WRT320N routers IP address to use it as an access point only and bring it in the IP range of my ccombined modem/router I'm not able to view the setup page via the new IP address. I have tried to change the IP from the default 192.168.1.1 to 192.168.178.2. After changing and applying the changes I restarted the router and tried to access the router via the new address. This was not possible am I doing something wrong or did I forgot something?
View 8 Replies View RelatedI have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access
View 1 Replies View RelatedI try to change the wmm settings to video, but it's always going back to background settings after saving.I already re-uploaded the firmware, but with no result...I noticed that is a newer firmware available for the WET610n where they solved this issue, but they haven't changed it for the WAP610n....
View 9 Replies View RelatedI have a new WAP54G Access point in our network. I would like to change WPA security settings, but am not able to do it.I have done everything as installation leaflet says, and I get to the 5th point Status sheet: Firmware version v.304, MAC address (numbers), IP address 192.168.1.245, SSID linksys, Channel channel 6 and WEB security Disable
What I would like to do, is change SSID and have WPA2 security. When I am clicking "Yes", it goes to the next sheet "Password", I write admin and click "Enter". I will have Pop-up window "Setup Access violation at address 0049BDB6 in module 'Setup.exe'. Write of address C933016A."
Purchased E3200 and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E3200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 2 Replies View RelatedWhen I try to enable remote management on my Linksys E3200 I get an "illegal value" message. Is there something else I need to change
View 2 Replies View RelatedI have setup an FTP site using the USB attached storage on my router. I would like to track when the site is accessed from the Internet. The logs don't show anything because the site is on the other side of the router. Is there a way to track activity to / from the site?
View 1 Replies View RelatedIs it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies View RelatedI have been trying to resolve what I think is an issue with DNLP or broadcast data getting to computers connected to my E3200. I have been wiresharking my network, trying different configuration, and scouring the web looking for an answer. My network is setup as shown below. The E3200 is on the same subnet and wired to the switch using the LAN port.DHCP is turned off. UPnP is enabled. DHCP is provided by the WRT54GL and turned off on the E3200.
WesternDigital has a program called "WD QuickView" and another called "WD Smartware" which together provide feedback about the drive status and real time backup capability (I prefer not to argue the +/- of these programs if folks don't mind <grin>). I have two computers on the wired LAN at the 16 port switch on which these programs work just fine. I get feedback about the drive status and backups occur. I also have two computers on the wireless LAN through the E3200 which DO NOT get feedback about drive status and appear not to detect the drive through the software. I CAN however access the drive by mapping it on Windows explorer for example.
With wireshark I do see chatter between the NAS and the E3200 (TCP traffic which I am not sure about...dpkeyserv stuff). I see broadcasts from the NAS to 239.255.255.250 often followed by talk between one of the wired computers and the NAS (which I am thinking is the comms for the WD...not sure though). I do not see chatter between wireless connected computers and the NAS (except for SMB or transferring files). It seems that the E3200 is not forwarding broadcasts to the computers connected to it even though it is connects as a switch.
My E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.
View 6 Replies View RelatedThe issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies View RelatedI've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 Replies View RelatedWhen accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies View RelatedI finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies View RelatedIs there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies View RelatedWhat happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedI'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedI brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
View 5 Replies View RelatedI just bought a brand new Linksys Cisco E3200 router. I set almost everything up in my house through the included software and went to port forward for some of my games. I realized I had something wrong with the ports and when I went back to access the ports through the web by typing in 192.168.1.1 which is the way I originally did the ports I could not. I then opened the software that came with the router and it could not detect the wireless network even though that is what I am using to type this now.
View 1 Replies View RelatedHow do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View RelatedHow to install linksys wireless router to access point?
View 1 Replies View RelatedCan I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?
View 1 Replies View RelatedI have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
View 9 Replies View RelatedI'm currently using my WRT320N router as an access point (connected to another linksys router), but I've lost my username and password to access the web-based utility. So I need to press the reset button and set it up again. Currently everything is working fine, but I've forgotten how to configure the router for this purpose, and I can't find instructions in the user's guide online. I seem to remember it being troublesome. I know I have to assign a different IP address (currently I'm using 192.168.1.113.) What other settings (if any) need to be changed?
View 2 Replies View Related"Can I get my E2100L to receive a wireless signal from a different model Wireless Router and repeat it via wireless and Ethernet. Yes or NO?"
- If so, how, if u need to user guide here: E2100L User Guide
I am using a newer wireless router but would like to use my older wrt54g router as an access point (wired and wireless) at the other end of my house. how to do it, and what the specific settings should be, especially the security settings. I can connect the wrt54g via a homeplug (cannot run a LAN cable). I had previously tried an Aztech wireless homeplug but found the security feature to be worthless and everyone was able to "break-in".
View 3 Replies View RelatedCan the EA6500 be set up as an access point connected to a remote router which has a connection to the DSL modem?I want to replace one of my wireless access points with a faster wireless interface, but this will be connected via hard wire CAT-5 cable located away from my modem/router.
View 3 Replies View RelatedI have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point. Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?
View 1 Replies View Related