I've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 RepliesI'm wondering if there are other hidden E4200V2 menus.
I didn't think the advanced wireless settings were there on this router, but they are and are accessible by an URL: [URL]
I'm wondering what else is actually in there and not on the web GUI?
Has anyone discovered any other portions of the firmware that are hidden and accessible via an URL entry?
What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedPurchased E3200 and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E3200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 2 Replies View RelatedWe're trying to connect our Linksys E3200 via ethernet wire to an existing company network that already has a router and switch - it will simply be connected to a port on our switch, and needs to function as an access point only (no DHCP, no routing, no NAT, etc.).
View 3 Replies View RelatedWhen I try to enable remote management on my Linksys E3200 I get an "illegal value" message. Is there something else I need to change
View 2 Replies View RelatedI have setup an FTP site using the USB attached storage on my router. I would like to track when the site is accessed from the Internet. The logs don't show anything because the site is on the other side of the router. Is there a way to track activity to / from the site?
View 1 Replies View RelatedIs it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies View RelatedI have been trying to resolve what I think is an issue with DNLP or broadcast data getting to computers connected to my E3200. I have been wiresharking my network, trying different configuration, and scouring the web looking for an answer. My network is setup as shown below. The E3200 is on the same subnet and wired to the switch using the LAN port.DHCP is turned off. UPnP is enabled. DHCP is provided by the WRT54GL and turned off on the E3200.
WesternDigital has a program called "WD QuickView" and another called "WD Smartware" which together provide feedback about the drive status and real time backup capability (I prefer not to argue the +/- of these programs if folks don't mind <grin>). I have two computers on the wired LAN at the 16 port switch on which these programs work just fine. I get feedback about the drive status and backups occur. I also have two computers on the wireless LAN through the E3200 which DO NOT get feedback about drive status and appear not to detect the drive through the software. I CAN however access the drive by mapping it on Windows explorer for example.
With wireshark I do see chatter between the NAS and the E3200 (TCP traffic which I am not sure about...dpkeyserv stuff). I see broadcasts from the NAS to 239.255.255.250 often followed by talk between one of the wired computers and the NAS (which I am thinking is the comms for the WD...not sure though). I do not see chatter between wireless connected computers and the NAS (except for SMB or transferring files). It seems that the E3200 is not forwarding broadcasts to the computers connected to it even though it is connects as a switch.
how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 Replies View RelatedMy E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.
View 6 Replies View RelatedThe issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies View RelatedInternet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies View RelatedThe Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies View RelatedI am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies View RelatedWhen accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies View RelatedI just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
View 9 Replies View RelatedMy WRT120N router doesn't have Internet Access Policy when I access it.
View 2 Replies View RelatedI have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies View RelatedI setup E4200 good. But, in Access Restrictions, there is no policy to choose from. Just Parental controls only.restore the Internet Access Policy like the good old routers?
View 1 Replies View Relatedwhy i can't add a new policy. I can't fillin a policyname or change the status from disable to enable. I have model V2 with firmware v2.0.03 build 007Jul 2, 2009
View 3 Replies View RelatedI'm just about to trade-in an E4200v2 for a E4200v1, primarily to regain the "Internet Access Policy" capability.
Just wanted to do a reality check with those of you who tried/use IAP... does it work basically as advertised?
I would be using IAP to specify MAC addr's of devices, blocking them from certain URL's and limiting their hours of Internet access.
And I plan to have Linksys's DHCP Server turned OFF, since my Windows Server handles DHCP on my network.
Should I expect all of this to work OK? No major reliability problems with IAP?
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies View RelatedOn E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
Is there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies View RelatedI just bought a brand new Linksys Cisco E3200 router. I set almost everything up in my house through the included software and went to port forward for some of my games. I realized I had something wrong with the ports and when I went back to access the ports through the web by typing in 192.168.1.1 which is the way I originally did the ports I could not. I then opened the software that came with the router and it could not detect the wireless network even though that is what I am using to type this now.
View 1 Replies View RelatedI am trying to get layer 7 application protocol to work in a simple test setup, I need to get this working to filter roommate traffric . Simple configuration with two interface(inside and outside). With layer application configured, everything works fine, but when applied layer 7 it does not block the web site i want... URL filter and parameter map don't work either...
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3)
parameter-map type urlfilter URL-FILTERaudit-trail onparameter-map type regex humoronpattern [Hh][Uu][Mm][Oo][Rr][Oo][Nn][.][Cc][Oo][Mm]
parameter-map type regex LAPOSTE1pattern LAPOSTE.NET(code)
I have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies View RelatedJust got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies View RelatedSince I have this router E4200 my network undergoes changes alone. I have a MAC filtering as I had in my previous WNRL 160N and had no problems but here the overnight me are the 14 that I have enabled MAC, put another 3 that are not from where I changed the settings WiFi network, I've put in hidden, change encryption type and others and continues to happen randomly, and I added the router directly to the list of allowed MAC. I have remote management disabled in the Cisco Network Magic are not those MAC. not because it adds the MAC and I removed some that I have put the single.
View 9 Replies View RelatedI am trying to filter a URL, facebook and it is not working. I have tried rebooting the router and it is still allowing access. I have provided the settings and ranges for PCs.
View 3 Replies View Related