I setup E4200 good. But, in Access Restrictions, there is no policy to choose from. Just Parental controls only.restore the Internet Access Policy like the good old routers?
View 1 RepliesWhat happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedI'm just about to trade-in an E4200v2 for a E4200v1, primarily to regain the "Internet Access Policy" capability.
Just wanted to do a reality check with those of you who tried/use IAP... does it work basically as advertised?
I would be using IAP to specify MAC addr's of devices, blocking them from certain URL's and limiting their hours of Internet access.
And I plan to have Linksys's DHCP Server turned OFF, since my Windows Server handles DHCP on my network.
Should I expect all of this to work OK? No major reliability problems with IAP?
On E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
I'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
View 3 Replies View RelatedI have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
View 1 Replies View RelatedI decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
View 6 Replies View RelatedI am trying to get a cell phone to have access to my LAN from 3am to 7am. I gave the policy a name, allowed access, checked everyday and the time 3a to 7a. Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.
View 2 Replies View RelatedI keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.
View 3 Replies View RelatedI am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies View RelatedI have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
I want to set up access restrictions to one MAC address (my kid's machine) basing on week days. From Su to Th allow less access time while during Fr-Sa afternoons access time should be longer. The question is how to program it in router. I know I can set rules with "allow" and "disable" keyword, but I don't know rules preference. When I set (Su-Th 6-21) allowed access time then router automatically denies defined machine internet access outside this time range. The problem is in the power of thus calculated denying time. I want to allow more access time in weekend, so I hoped if I can simply add "Fr-Sa 6-22:30 allowed access time" rule. I hoped that router will regard explicitly set time over inexplicitly set time but it appears it is not so. What are their preferences/priorieties, iis it possible to stack more rules affecting one MAC address or it is so simple that the first rule "rulez"? Is it possible to set more than one time rule affecting the one machine?
View 4 Replies View RelatedI had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies View RelatedAccess Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedHow do I restrict wireless user from accessing download sites that slow my network?
View 1 Replies View RelatedRecently switched from WEP to WPA2 on the router and let it run a few days. Everything was copacetic.
Then decided to implement the following access restrictions:
1 - Target MAC based, internet blocked from 9-11:55 PM (why won't it let you block from 9PM-7AM ;-( ), blocks son #1's laptop, Kindle
2 - Target MAC based, internet blocked from 10-11:55 PM, blocks son #2's Kindle
3 - Targets IP Address range based (192.168.1.0 - 192.168.1.254), across all devices blocks several porn sites all the time
I can get on a play games online but when we start watching video with all 3 restrictions enabled, it will eventually disconnect (can take 1-5 minutes before it happens). Rebooting XBox usually reset connection, but it would happen again eventually. After disabling all restrictions, disconnects completely stopped.
Is it not possible to have Access Restrictions in place on a WR54G and still stream video?
I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]
View 2 Replies View RelatedI 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
View 5 Replies View RelatedI have been looking into this router, I would like to know if I can enable Parental controls or access restrictions to block a MAC or IP address; from 03:00 AM - 06:00 AM ?Instead of Midnight to 6:00 am.My E4200 works just fine, Just would like to know if the EA6500 Can do that ?
View 7 Replies View RelatedInternet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies View RelatedThe Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies View RelatedI have an EA3500. PPPoE connection. Can't seem to choose my DNS server (use Unblock-US) since the router insistently forces me to use the DNS from ISP.How can i work this around? I'm kinda tired of people asking me why i am changing the DNS. I want to change the DNS and that's final. It's a resource like any other and i want to use it.P.S: i tried most of the basic troubleshooting. I tried my old router back on and the DNS's works fine. I tried even conecting the old router re-routing the new one, and the other router manages the selected DNS's servers fine.
View 9 Replies View RelatedI just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
View 9 Replies View RelatedMy WRT120N router doesn't have Internet Access Policy when I access it.
View 2 Replies View RelatedI have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies View Relatedwhy i can't add a new policy. I can't fillin a policyname or change the status from disable to enable. I have model V2 with firmware v2.0.03 build 007Jul 2, 2009
View 3 Replies View RelatedI've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 Replies View RelatedHow to time access restrictions with WRT120N router a wireless network?
View 7 Replies View RelatedI set the access restrictions as instructed but they refuse to work. Firmware version is :-1.01.05,have rebooted, with no success.
View 6 Replies View RelatedI'm trying to take off the strict nat restriction.
View 1 Replies View RelatedI recently purchased a WAG320N router and have issues with access restrictions. Internet is shut down regardless of the time set with the policy or policies. I am using firmware version V1.00.12. Tried rebooting router, restoring factory defaults & restarting IMAC to no avail. Timezone checked and OK.
View 5 Replies View Related