I keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.
View 3 RepliesI am trying to get a cell phone to have access to my LAN from 3am to 7am. I gave the policy a name, allowed access, checked everyday and the time 3a to 7a. Under edit list of PCs, I entered the MAC address of the phone, and I have also entered the MAC address of the phone on the wireless>edit mac filter list, though didn't know if I should.
View 2 Replies View RelatedHow to time access restrictions with WRT120N router a wireless network?
View 7 Replies View RelatedWRT54G FW V8.00When enable an access restriction policy that blocks websites by keyword (facebook, twitter, etc) the policy works for a short time (< 2 hours) and then all traffic will be stopped. I can't even log into router. Power down and up is only way to re-enable the router
View 1 Replies View RelatedIs it possible to have a WLAN only be active during set times of the day?.I have a WLCM in a 2811 router but I can't find any type of setting that will let me enabe a WLAN at 6pm and disable it at 7am.
View 3 Replies View RelatedWhat happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedI'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
View 3 Replies View RelatedI have access restrictions set up for certain wireless devices in my home that the kids use to kick them off at 11 pm and keep them off all night. where I am running into a problem is I want to block these same devices from downloading anything without my permission my son downloads everything he sees, Comcat has already threatened to kick us off their service if we go over 250 gb bandwidth use in a month again. so I want to configure something in the router that will block all downloads for specific wireless devices. with the access restrictions I have set up I used the mac address not just the ip so they have no way around it I constantly monitor what is connected. I am using the stock firmware as well
View 1 Replies View RelatedI decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
View 6 Replies View RelatedI am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies View RelatedI have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
I want to set up access restrictions to one MAC address (my kid's machine) basing on week days. From Su to Th allow less access time while during Fr-Sa afternoons access time should be longer. The question is how to program it in router. I know I can set rules with "allow" and "disable" keyword, but I don't know rules preference. When I set (Su-Th 6-21) allowed access time then router automatically denies defined machine internet access outside this time range. The problem is in the power of thus calculated denying time. I want to allow more access time in weekend, so I hoped if I can simply add "Fr-Sa 6-22:30 allowed access time" rule. I hoped that router will regard explicitly set time over inexplicitly set time but it appears it is not so. What are their preferences/priorieties, iis it possible to stack more rules affecting one MAC address or it is so simple that the first rule "rulez"? Is it possible to set more than one time rule affecting the one machine?
View 4 Replies View RelatedI had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies View RelatedAccess Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedHow do I restrict wireless user from accessing download sites that slow my network?
View 1 Replies View RelatedRecently switched from WEP to WPA2 on the router and let it run a few days. Everything was copacetic.
Then decided to implement the following access restrictions:
1 - Target MAC based, internet blocked from 9-11:55 PM (why won't it let you block from 9PM-7AM ;-( ), blocks son #1's laptop, Kindle
2 - Target MAC based, internet blocked from 10-11:55 PM, blocks son #2's Kindle
3 - Targets IP Address range based (192.168.1.0 - 192.168.1.254), across all devices blocks several porn sites all the time
I can get on a play games online but when we start watching video with all 3 restrictions enabled, it will eventually disconnect (can take 1-5 minutes before it happens). Rebooting XBox usually reset connection, but it would happen again eventually. After disabling all restrictions, disconnects completely stopped.
Is it not possible to have Access Restrictions in place on a WR54G and still stream video?
I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]
View 2 Replies View RelatedI setup E4200 good. But, in Access Restrictions, there is no policy to choose from. Just Parental controls only.restore the Internet Access Policy like the good old routers?
View 1 Replies View RelatedI 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
View 5 Replies View RelatedSet my DIR-655 to limit my son's time on the Internet. I have all the connections set to the MAC Addresses
View 4 Replies View RelatedI have been looking into this router, I would like to know if I can enable Parental controls or access restrictions to block a MAC or IP address; from 03:00 AM - 06:00 AM ?Instead of Midnight to 6:00 am.My E4200 works just fine, Just would like to know if the EA6500 Can do that ?
View 7 Replies View RelatedIs there a way to set up the WAP for specific times of access?
View 1 Replies View RelatedLooking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
View 1 Replies View RelatedI set the access restrictions as instructed but they refuse to work. Firmware version is :-1.01.05,have rebooted, with no success.
View 6 Replies View RelatedI'm trying to take off the strict nat restriction.
View 1 Replies View Relatedi have router lynksys WRT120N and the latest 1.0.0.7 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
View 5 Replies View RelatedI had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
My own sites were down & I can't view them on my computer now.This is the 2nd time this has happened to me with router WRT54G.Every time there's a problem with my hosting company & my sites go down, my router blocks them once the sites are back up & running.When I plug directly into the modem I can access them, but then I can't use my phone, etc.I've recycled & I keep trying to find how you save your settings on your router so I can do a cold reboot, but I can't find the instructions anywhere.Why does it keep doing this & how to save the settings & restore them.
View 2 Replies View RelatedI am using a newer wireless router but would like to use my older wrt54g router as an access point (wired and wireless) at the other end of my house. how to do it, and what the specific settings should be, especially the security settings. I can connect the wrt54g via a homeplug (cannot run a LAN cable). I had previously tried an Aztech wireless homeplug but found the security feature to be worthless and everyone was able to "break-in".
View 3 Replies View RelatedI can't access the router through the IP within the browser. It's an older WRT54G. I've never used the downloaded software that allows you to connect to it, but that's what I was going to try.
View 1 Replies View RelatedI have a E4200 as well as a WRT54G. I'm looking to create two different access points to the same network, one access point being 802.11g (WRT54G) and the other being 802.11n (E4200) I want to do this because I need the extra speed from 802.11n for streaming video to my consoles. The problem is that there are multiple devices that only reach up to 802.11g. Would it be possible to plug the WRT54G into the E4200 in order to give a second access point (probably with different SSID) so that 802.11g devices can connect to the network, without having to destroy my 802.11n network? The WRT54G is currently running DD-WRT.
View 3 Replies View Related