I have setup an FTP site using the USB attached storage on my router. I would like to track when the site is accessed from the Internet. The logs don't show anything because the site is on the other side of the router. Is there a way to track activity to / from the site?
View 1 RepliesPurchased E3200 and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E3200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 2 Replies View RelatedWe're trying to connect our Linksys E3200 via ethernet wire to an existing company network that already has a router and switch - it will simply be connected to a port on our switch, and needs to function as an access point only (no DHCP, no routing, no NAT, etc.).
View 3 Replies View RelatedWhen I try to enable remote management on my Linksys E3200 I get an "illegal value" message. Is there something else I need to change
View 2 Replies View RelatedIs it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies View RelatedI have been trying to resolve what I think is an issue with DNLP or broadcast data getting to computers connected to my E3200. I have been wiresharking my network, trying different configuration, and scouring the web looking for an answer. My network is setup as shown below. The E3200 is on the same subnet and wired to the switch using the LAN port.DHCP is turned off. UPnP is enabled. DHCP is provided by the WRT54GL and turned off on the E3200.
WesternDigital has a program called "WD QuickView" and another called "WD Smartware" which together provide feedback about the drive status and real time backup capability (I prefer not to argue the +/- of these programs if folks don't mind <grin>). I have two computers on the wired LAN at the 16 port switch on which these programs work just fine. I get feedback about the drive status and backups occur. I also have two computers on the wireless LAN through the E3200 which DO NOT get feedback about drive status and appear not to detect the drive through the software. I CAN however access the drive by mapping it on Windows explorer for example.
With wireshark I do see chatter between the NAS and the E3200 (TCP traffic which I am not sure about...dpkeyserv stuff). I see broadcasts from the NAS to 239.255.255.250 often followed by talk between one of the wired computers and the NAS (which I am thinking is the comms for the WD...not sure though). I do not see chatter between wireless connected computers and the NAS (except for SMB or transferring files). It seems that the E3200 is not forwarding broadcasts to the computers connected to it even though it is connects as a switch.
how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 Replies View RelatedMy E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.
View 6 Replies View RelatedThe issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies View RelatedI've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 Replies View RelatedI am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies View RelatedWhen accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies View RelatedI finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies View RelatedIs there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies View RelatedI just bought a brand new Linksys Cisco E3200 router. I set almost everything up in my house through the included software and went to port forward for some of my games. I realized I had something wrong with the ports and when I went back to access the ports through the web by typing in 192.168.1.1 which is the way I originally did the ports I could not. I then opened the software that came with the router and it could not detect the wireless network even though that is what I am using to type this now.
View 1 Replies View RelatedI downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
View 2 Replies View RelatedWe'r using Linksys CISCO WRT610N and WRT310N wireless router.Our requirment using web access restriction is that we've to Block some website and the corresponding setting is going to be applicable to all users who are accessing internet through this router. The people who are accessing internet through corresponding router should not be able to access web site which are restricted in Router setting. There is the Setting with name "Web Access Control etc etc ".
View 9 Replies View RelatedI have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
I have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies View RelatedTrying to convert a spare router (Linksys E3200) into a wireless access point toextend my wireless coverage. I thought knew how to do this but having a problem.Steps I followed are:1. Disable the E3200 DHCP server2. Change E3200ip address from 192.168.1.1 to something else3. Disable the firewall4.Make wireless settings5. Connect it lan port to lan port with primaryrouter.The problem I am having is that after I finish step 2 the routerreboots with the browser trying to access it at the new ip address. But thebrowser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected byan ethernet cable to an E3200 lan port. I also tried it wireless with the same result. Browser will not connect at any ip address except 192.168.1.1 and then only after I factory reset the beast to regain the 192.168.1.1 ip address
View 3 Replies View Relatedafter messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies View RelatedI just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?
View 1 Replies View RelatedI have been using an E3200 and it has been working great. I know have a need for wireless coverage in a distant part of my house and the current router won't get there. I also need wired in that spot of the house as well. I thought to buy a e1200 to use it as a WAP for that part of the house and also to have a few Ethernet ports come off it. Can I connect to my original E3200 wirelessly from the e1200 and then use the e1200 as a WAP and for Ethernet?
View 7 Replies View RelatedI just upgraded my router from 1.0.03 to 1.0.04, I have a few questions:After installing the firmware, I pressed the reset button at the back for almost 1mn, the power lighted as expected, I then unplug the power cord for 30 sec.The strange thing is that this did not lead to a reset of the configuration, all my settings are still here...!But the actual problem is that my internet speed is divided by two, I still have to confirm this observation on the long term.
View 1 Replies View RelatedI have to reboort my router every day to get back an internet connection? I have a desktop and a laptop plus iPads, etc. The laptop loses connectivity every day about the same time. My only solution so far is to reboot the router. I realize that the client lease time is set to 1 day by default but isn't it supposed to ask the modem for another day of life when this happens?
View 5 Replies View RelatedI'm using a DSL line that changes IP's. I have the E3200 set to auto, but everytime the IP changes, my internet goes down, and I get an ip of 127.0.0.1 on the status page. I then have to renew the ip and reboot. This happens once a day, usually.
View 3 Replies View RelatedI have a 6 year old wrt54g that is working fine but old. I want to upgrade and will go with the 3200 or 4200. I really don't need the extra features on the 4200 since everything I have is hardwired (directly to two laptops and to two switches in other parts of the house for tv and printer). I want wireless for times when we move a laptop but it wouldn't be all the time, and we won't (for now) use the media options. The difference in price between the 3200 and 4200 is less than $25 so costs is NOT a factor in deciding.So should I just purchase the 4200 since price is not a factor or go with 3200; I want the most stable of the two and will never need the extra wireless features in the 4200.
View 8 Replies View RelatedI used to have a Belkin router which was losing connectivity throughout the day for a few short moments. After looking at the logs it appears it was issueing a DHCP release randomy which explained the fault. Since it was old router I decided to replace it with a E3200. This worked fine for a few days but then I started to see similar symptions. So currently I am trying to figure out if it's the same issue as before. I tried looking for a log on the router to see if it was also losing/releasing the WAN IP, but apparently the router doesn't log it. I spoke to a tech rep on chat, but I don't think they understand what I was talking about (how frustrating). I even tried to explain it another way that if I hit the 'Release IP address' button and then hit the "Renew IP Adresss' button does this activity get logged.
Where can I find a log to see DHCP activity (on the WAN interface)? There is a DHCP log which shows all the LAN activity but this is not what I need for this issue. I find it hard to believe a mature vendor like Linksys doesn't log this activity?
House has 2 floors. I want to install 2 E3200, one on each floor, but both with the same SSID/Password, etc. so internet connection/streaming throughout the floor is seamless.
Both floors have network wall sockets ready and they all lead to the same modem/router so all devices plugged lead to the same network.
PS. both E3200 have been update to Firmware Version: 1.0.03
I have bought Linksys E3200 less than month ago.I have setup it, connected HD (WD My Book 1TB) through USB and it work good, without any problem.Than week ago, I turned off the router, because of my vacation. Yesterday, I came back, turned on the router. WiFi was working good, cable connection too. But there was no connection to HD. I had checked information about HD on admin page, router understood that it is HD, but not provided share access to folder, also, there was no button, to setup it.I disconnected HD, tried to connect it using the Cisco Connect, it provided mistake with USB connection to HD and than with HTTP connection to router. I disconnected HD, tried to connect it manually: connect HD -> go to admin page -> refresh to show HD -> admin page freeze... -> reboot of router manually.
There was a lot of tries to connect HD, but all was failed.I connect HD to computer, it works successfully.I checked connection to router through USB, using my card reader and SD flash card, it works successfully.Information about HW:
1. Linksys E3200, last update of firmware for German (was bought using German Amazon) country. (Cannot check it now, if needed will check)
2. Computer: Windows XP SP3
3. WD My Book 1TB (NTFS)
I updated my E3200 to 1.0.04 to try to resolve a wireless dropping issue. Now the connected USB storage no longer responds correctly (very delayed if connecting at all). When I try to provision new storage via the routers admin page, I do not get the permissions page.
View 9 Replies View RelatedI just picked up the E3200 and love it. This morning I hooked up my printer via the USB. Everything went smooth until I tried to print something. I thought nothing was happening, but I let it sit for a while. While I was waiting, I was messing around with my network setting in windows. I realized that my network had been set to 'work' for some reason, so I changed it to 'home'. As soon as I did, my printer spit out my test page. (probably 5 min after sending the doc.) I don't know if it was just coincidence or what, so I sent another page and nothing happened (yet).
Is this common to take that long? Is there a way to speed this up?
I've just bought a linksys E3200 wireless router and it hasnt performed even alittle up to expectations.. As above stated, the router keeps disconnecting me from the internet and i do not know how to fix it. It gets really annoying especially when i have to use the internet to do work.
View 9 Replies View Related