What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedMy network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies View RelatedI just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedI would like to ask if its possible to remotely access a WAP54G?
View 3 Replies View Relatedmy wap54g is not working even i hold reset butoon for 60 second it not woring even my linksys wap54g reset button is not work for reset it, It not do any thing and still i cant accest is web interference
View 9 Replies View Relatedhow to set up a WAP54G v3.1 Access Point if you've misplaced the CD?
View 5 Replies View RelatedMy Linksys Range Extender died. So I bought a WAP54G thinking that I could use it as a repeater to extent the range of the signal from my router to the other wireless PCs in the house.
1st floor:
PC1 connected to a WRT54G v.5 router
PC2 connected to PC1 router via USB network adapter
Laptop connected to PC1 royter via internal wireless
2nd floor
PC3 connected to PC1 router via USB network adapter
PC4 connected to PC1 router via USB network adapter
The main goal is to set up the WAP54G in between PC1 and the other PCs to extent the range of the signal particularly to the 2nd floor PCs.The instructions for configuring the WAP54G are fairly straightforward, but the first issue I run into is not being able to connect to the WAP54G web setup. I am using the following instructions:
[url]...
once I configure or setup the WAP54G through another PC as a repeater, will I be able to disconnect it from the PC and use it as a standalone (e.g., plugging only the power in and leaving it in my kitchen or a hallway) to extend the range of the signal? Or does it have to stay connected to PC1 and does PC1 always have to be on for this WAP54G to act as a repeater?
My WAP54G no longer has power -- the power light does not come on. I've unplugged the unit and moved it to a variety of different outlets that I know work.
View 5 Replies View RelatedI have an old WAP54G v3.1 and I want to access the menu but cannot, the IP must have been changed and even resetting does not let me in. What can I do?
View 4 Replies View RelatedI have a WAP54G as my access point, currently it is connected with my BEFSR81 router. I am thinking of changing the access point to a WAP610N for the house. I know that this would work but I was wondering if the WAP54G could be used as a repeater for the outside (I know a lower speed). I know they are two different channels but I wanted a larger range for my wireless. I am on Windows XP, SP2, using Firefox. Can this be done?
View 4 Replies View Relatedi have been using a couple of wap54g units for years now (awesome units!) but its now time to upgrade to "N".is there a newer unit that has "N" ?is there a unit that has a PoE option? also, i really like the ability to switch to larger antennas like the wap54g unit does. i would think that all wireless access units should have removeable antennas and a PoE option!
View 6 Replies View RelatedMy mac has been overwritten on 2 of my APs, they are now totaly different than before and identical ? they now both show 00:90:4C:91:00:01
View 9 Replies View RelatedAccording to the information on the bottom of the WAP54G setup screen it can connect to the WRT54G without another WAP54G. What I want to do is use the WAP54G as a bridge to connect my DVD player with an Ethernet connection to the internet via the WRT54G. Both units have the latest firmware updates. When I set it up as I believe it should be the WAP54G has all the lights on but the DVD player cannot connect to the internet.
View 5 Replies View RelatedHow do I connect three or more WAP54G's in bridge.
View 3 Replies View RelatedI have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies View Relatedafter several years of proper functioning my WAP started to make trouble and recently stopped working. I've tried a lot of options to get it back online but I failed doing so.The green ACT LED won't light up anymore so my laptop cannot find the WAP anymore. When connecting the WAP directly to the laptop the Network Center shows that Windows is trying to identify the WAP but this messages disappears and re-appears on and on but there is no succes in identification (ofcourse this is caused the the green ACT LED which won't light-up).
View 1 Replies View RelatedI just bought this used WAP54G, trying to link it to my home WLAN network, using my WRT54GS. I was able to get into to it, and change the configurations to match my network. But I still can't get access to it via wireless? I can still get back in via wired. How do I know(or not know) that the wireless part of this box works?
View 2 Replies View RelatedI am unable to connect wirelessly to a WAP54G v2 with a Dell Inspiron 17R/N7010 running Windows 7. In fact, previously a relative's laptop, also running Windows 7, was also unable to connect at my location.The access point has no security enabled. It shows up in the list of available wireless networks. I've configured the wireless adapter properly (static ip). Yet connection fails. Windows suggests that I power cycle the access point and try again. If I use the same configuration for the wired connection, it works. Is there a compatibility issue with Windows 7 and the WAP54G v2?
View 6 Replies View RelatedI just took over a position where I had to reset a WAP54G because no one knew the encryption key. In working with some of the wireless access points in the past, I know that they came with setup or utility software to find and configure. where I can get a copy. I couldn't find it on Linksys' site.
View 3 Replies View RelatedIt looks like the two are functionally compatible but will the ANT5959 connectors mate with the ones on the WAP54G box after the supplied dipoles are removed?
View 2 Replies View RelatedI have a WAP54G wireless router that worked fine at our other house, but we have moved and I'm trying to set it up. (I was not the one who originally hooked it up at the other house.) I am trying to hook it up to our Charter internet which works just fine with my Mac if I just connect a cable between the Mac and the 'box' that Charter hooked up. When I plug in my husband's PC with the cable in the same way I plug in my Mac, his will not work. He has an internal internet connection that he connects to wireless, but it is really slow. This means that I cannot use Rick's PC to set up the router, because it cannot be hooked up to the cable source.
View 1 Replies View RelatedI have never setup an wireless access point before and am having some issues. I have a Linksys WAP54G ver 3.1. A friend gave it to me and he said it was working when he pulled it out of his office.I defaulted the device and using the wizard have the following setup:
Setup:
Network:
Device Name - Linksys WAP54G
Configuration Type - Static IP
IP Address: 10.0.0.239
Subnet Mask: 255.255.255.0
[code]....
When I try to connect to it via my laptop I get the error: "Windows was unable to connect to XXXXX"
I am running my home network and WAP(WPA2) behind a d-link gaming router (DHCP) with no inbound or outbound restrictions; however, I am unable to access the internet using my ipad unless I put the WAP in the DMZ. Also, if I configure security using the setup program, I can not log on to the web based utility. I have to disable security with the set up program and then log into the utility. BTW..the UID must be left blank to log into the utility( PW only) to configure the WAP, even though the manual says otherwise.
Now after all this, the WAP will be up and running for days even a few weeks. Then for no reason it will no longer be accessible and I will power it down and back up and it works fine. But this will work only a few times and I have to hit the reset button and reconfigure it all over again.
The firmware has been updated and nothing else has issues on the network. This has been happening since i bought it 3yrs ago, using an iPad, iPhone, Laptops, and PCs( XP and Windows 7) but in the past year it has been more frequent.
I have taken over maintenance of a customer site from another service provider. I need to reprogram several WAP54G units. I have reset the units with the reset button. However, this does not reset the admin password back to admin.
View 9 Replies View RelatedI have 2 WAP54G AP. I have office with internet connection near my home. How to connect these access points so i can get access to internet from home, but don't won't to anyone else can access that.
View 1 Replies View RelatedWe have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
This is becoming unwieldly, but it is safe. Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.
It works beautifully with the external antenna WRT54G, and WRT54GL, but will it work with the WRT54G series with an internal antenna? (repeater mode) What other products does it work with? (repeater mode?)
View 6 Replies View RelatedI reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies View Related
