Cisco :: Managing Lightweight Access Points In Ciscoworks LMS 4.0?
Jul 25, 2011Is it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco Wireless :: 5508 - DHCP Option 43 For 1130 And 1300 Lightweight Access Points?
Mar 14, 2013I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedCisco Wireless :: Aironet 1040 Access Point Managing
May 22, 2012We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
View 5 Replies View RelatedCisco :: Configure Lightweight Access Point LAP1242AG As 802.1x Supplicant?
Jul 29, 2012Is possible to configure a Lightweight Access Point LAP1242AG as 802.1x supplicant using Microsoft NPS radius server that not use EAP-FAST authentication method? Can I use PEAP in NPS radius?
View 6 Replies View RelatedCisco Wireless :: 262N Lightweight Access Point Work With 4402
Apr 4, 2012Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedCisco Wireless :: AIR-CAP3502I-N-K9 - Change Regulatory Domain On Lightweight Access Point?
Mar 22, 2012I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
Cisco Wireless :: Reset 1522 Series Lightweight Access Point To Factory Default?
Jan 13, 2013I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedLinksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?
Nov 24, 2011I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.
View 3 Replies View RelatedWifi Access Points With User Access Control?
Nov 27, 2012We have a small office and already have a firewall in place that uses content filtering. I am looking for a low cost wireless access point that I can place behind my firewall that will allow me to control access by a username and password list, not just the passkey.
Does this exist without having to go to an Aruba or Ruckus type enterprise WIFI product?
Guest Internet Access - Multiple Access Points?
Dec 13, 2012Here is my setup:
Netgear WNDR3700 - Main router, DHCP turned on
4x Netgear WNR2000 - Setup as Access Points (DHCP turned off), connected to main router via LAN ports
I only want the guest network to have internet access. I have the guest network enabled on the router and access points with the option to "Allow Guest network to access main network" disabled. My problem is that since the access points aren't hooked directly to my modem via the WAN port, the guest network broadcasted from the access points does not have internet access.I have read up on setting up a separate subnet for the guest network using DD-WRT but was curious if there was a way to get the desired result with the stock Netgear firmware.
1 CPU With 6 Access Points?
Mar 15, 2011I am looking being able to control one computer at 6 stations. Each station will contain a keyboard, monitor, and mouse.They do not all need to be able to control or access the computer all at once. I would use a reverse kvm switch but I am looking at distances of 200-500ft between the stations/cpu.My last resort was to buy some cheap dells or build some low end computers and set up remote desktop but we would really like just having the keyboard, mouse and monitor.
View 10 Replies View RelatedAccess Points Going Default?
Feb 21, 2013I have some network devices that are connected to a 110v power source that goes through a 110v/5v power converter.The Access points keep going back to factory default settings and losing their configuration. I have the same access points installed in the same situation but on a different site that work fine.have changed both the configuration and firmware to be be identical to the working Access Points and still the others default.They do not do this at a specific time of day and out of the 6, they do this at random and not at the same time. Sometimes they will go 24 hours + without defaulting, sometimes they'll go just 4 hours.
View 2 Replies View RelatedDeleting Access Points From The Wii?
Dec 5, 2012I would like to know how to delete a connection from my network. When I connect to the Wii it automatically chooses the right connection. What I have noticed though is that there is a third connection for a printer that is not secured and I have no idea why it is there or has an option to connect to the internet.
View 4 Replies View RelatedCisco ASA5505 And Wireless Access Points
May 31, 2011We have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
Cisco :: Reboot Access Points Over WLC4404
Oct 3, 2012We have two Cisco Wireless Controller 4404 with the IOS Version 7.0.220.0 and a lot of access points (ca. 170). Now i wan't to reboot a group of Access points where i found over a filter..Or how can i reboot all the Access Points at the same time over the Controller Interface? Is it possible? I only found the option in the WebGui where i can reboot 1 Access Point at the same time with "hardware reset".
View 5 Replies View RelatedCisco Wireless :: WAP4410N Access Points Set Up
Apr 9, 2013I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Cisco :: 5508 NCS 1.1 Not Showing Any Access Points
Jul 16, 2012I have NCS 1.1 appliance and added a 5508 WLC running 6.0.199.4 code using snmpv3. Controller is added to NCS, but it doesnt show any AP's which are there on the controller. AP count is zero. I have another controller with code 7.0.230 added and showing AP's though. AP model is 1252.
View 5 Replies View RelatedCisco Routers :: 800 - Replace Access Points
May 22, 2013We have the following connection based in the services provided by our local telephone company, the connection arrives to a router Cisco 800 series. From the router, i send it connection to a switch SRW2024 v1.2 (Business series) 24-Port 10/100/1000 Gigabit Switch with webview. That switch is useful to send connection via RJ45 for a few of PCs. Then, I send connection to a switch SRW2008P (Business series) 8-port 10/100/1000 Gigabits with vieweb and power over ethernet. The last switch, send the signal via RJ45 to seven WAP2000 (business series) Wireless-G AP with PoE.
That network is running fine, but I've some problems to cover some areas within the building and sometimes the signal is really poor. The cable RJ45 between the PoE switch and each AP is no longer than 50 meters and each one with antennes about 8 or 9 Db.
So, now I've the possibility to change the access point for a power devices.
Cisco Wireless :: CDP On Access Points 3502 Aps
Mar 15, 2012Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
Wireless :: Change Between Access Points?
Aug 30, 2012At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View RelatedHome Hub - Add Wireless Access Points?
Nov 10, 2011BTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up
View 2 Replies View RelatedTwo Wireless Access Points With Two Routers?
Jul 5, 2012I have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.
I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.
IF its doable, how should the two be configured and connected.
Multiple Access Points 2 Routers
Apr 1, 2012I've recently bought another PC, but set it up in a different area than my existing computers. It's down in my basement, along with my PS3, Xbox 360, and Wii. Now the problem is connecting all of these "toys" to the internet. I only have one in-wall ethernet port, which my PC is currently plugged into. Leaving my PS3, Xbox, and Wii, only with an extremely weak wireless connection. Now, my original thought was just to buy a network "switch," BUT then I remembered I have an old D-Link router. So, logically I should be able to plug an ethernet into the wall, then into the WAD port on my router, then plug my Xbox, PS3, Wii, and PC into the 4 remaining LAN ports on my router. I want another WiFi access point using the same network, and a wired connection for all of my gadgets.
View 1 Replies View RelatedCisco :: 5508 WLC Remote Access Points Are Not Registering
Apr 17, 2012i have deployed WLC 5508 in head office with current 56 access points (mix of 1262N, 1141N and 1242) are regist ered and working fine, recently we extended to our remote office (connected over Layer 3 MPLS with OSPF Protocol) were none of the access points are not registering, i am able to reach to the controller from the specific VLAN and native VLAN without any issues. @remote site i have enabled option 43 and option 60 with the controller IP.
Number of APs.................................... 56
Global AP User Name.............................. ciscoGlobal AP Dot1x User Name........................ Not Configured
[Code]......
Cisco Wireless :: AIR-CAP3502E-E-K9 Access Points Not Joining WLC
Jun 17, 2012I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies View RelatedCisco Wireless :: Push Access Points To Second 5508 Via HA
Aug 9, 2012I am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedCisco Wireless :: 4400N / Finding Wi-Fi Access Points?
Nov 18, 2012I need an Wireless Access Point.Two SSID simultaneously in different IP Rangeit is with a simple browser GUI to manage? (not console and controller)a distance of about 50 (we can place multiple APs)N speedDual BandWhich series meets the above requirements?It can also Wireless-N Gigabit Router as 4400N, but it does not support Dual Band.
View 1 Replies View RelatedCisco :: 4400 Controllers Which Support 50 Access Points Each
Jun 25, 2011We have two 4400 controllers which support 50 Access points each and wcs with 100 base license.Now we added 5508 controller supports 50 access points.wcs is upgraded with another 50 ap license.The 5508 controller is joined to wcs and the licence showing permanent.WCS showing all aps and showing both 100 and 50 licence as permanent.But the issue is while loging into the wcs it showing the error message as"The system is in violation of license.The number of APs registered is greater then licensed."
View 5 Replies View RelatedCisco :: Preventing Unwanted Access Points 1242s
Feb 26, 2013This is just a tip that we used on our controllers that I wanted to pass along. We were having issues with unwanted access points associating to our controllers. We had a stack of older 1242s that came up missing and hit our network. On way we came up with to prevent this was to number all of our wlans above I'd # 16 on the controller. By default the default ap group allows all wlans from 1 to 16. By starting with 17 we are not allowing any SSIDs in the default group. All if our production access points are in their own ap groups. Any access point that hits our controllers that has not been configured with the correct ap group name will be in the default ap group and will not be servicing any SSIDs.I know there are other ways to set this up but this was a tricky way for us to set it up and see who calls about there wireless not working.
View 3 Replies View RelatedCisco Wireless :: 5508 IP Scheme For Access Points
Jan 17, 2013I have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies View RelatedCisco Wireless :: Supported Access Points On WLC 5508
Jul 13, 2011I need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.
View 1 Replies View Related
