Routers / Switches :: Need To Add Drivers To Wds Boot Image On 2003R2?
Jan 25, 2013How do I add network drivers to a wds boot image on 2003R2. I see that 2008 has the add driver option but that doesn't exist in 2003r2.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: C2960 Boot Image After Ios Upgrade
Dec 30, 2011 i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
Cisco WAN :: Boot Image Failover On 881G?
Apr 29, 2012We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies View RelatedCisco WAN :: 2621XM Router Will Not Boot From IOS Image
Nov 27, 2011I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
Cisco WAN :: Upgrade IOS For C2960 And Switch Does Not Boot From New Image
Dec 29, 2011I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
Cisco Firewall :: Setting A Boot Image On ASA 5505?
May 1, 2011I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
Cisco WAN :: 7204 VXR - Valid Image On Boot Flash
Oct 24, 2012I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
Cisco Switching/Routing :: 6503 E Series Boot Image
Dec 14, 2012I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies View RelatedCisco Wireless :: New AIR-LAP1142N-A-K9 Insufficient Memory To Boot Image
Nov 1, 2011I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
Cisco WAN :: 6509 System Image File Is Sup Boot-disk
May 27, 2013i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
Cisco Switching/Routing :: IE3000 Sw Cannot Load Boot Image
May 13, 2013I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies View RelatedCisco Switching/Routing :: 2960S Boot Loader And IOS Image
May 18, 2013after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
Cisco Switching/Routing :: Boot 4503-E Switch From Secondary Image?
Sep 13, 2011We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies View RelatedCisco Switching/Routing :: 7206VXR Boot Loader Image Upgrade
Jan 22, 2008I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedCisco Infrastructure :: Can 1841 Router Boot From System Image From USB Disk
Jan 12, 2013I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies View RelatedCisco WAN :: 2801 Unable To Boot Image Wrong System Software
Feb 28, 2011128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
Cisco Wireless :: 6513 - How To Access Memory On WISM To Delete Old Boot Image
Sep 22, 2012I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
Cisco Switching/Routing :: Nexus 5010 Won't Load System Image - Stuck At Boot Prompt
Sep 29, 2012I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
Cisco Switches :: SG200-08 Won't Boot Anymore
Feb 9, 2012When I came back home today I saw that my SG200-08 switch did not look fine.Basically, the system LED of the switch keeps blinking and end devices connected just don't have any network.I tried to reset the switch with the "reset" button (with a paper clip) the system LED was orange during just a second and then continue to blink.What is wrong with the switch?Is there a way to flash a new firmware and/or to delete the configuration file?
View 2 Replies View RelatedCisco Switches :: SGE 2000 24 Port POE Switch Won't Boot
Sep 16, 2012I have a sge 2000 24 port POE switch that won't boot, won't communicate on console or TCP/IP, and all of the port lights are lit up green. Holding down the reset button doesn't fix the issue and there aren't any lights illuminated on the left hand side of the switch.
View 1 Replies View RelatedCisco Switches :: SG200-50P Boot And PoE Related Errors
Apr 11, 2013I have a SG200-50P. It had a problem with the PoE ports (didn't supply power to my Bosch POE security cameras) so I updated it to the latest firmware. Now it does recognize the cemeras and supplies power to them. However, there are a few problems:
1. The boot time is extremely long, maybe 15-20 minutes for it to become ready. I've tried to reset to factory default settings, push the reset button for 30+ seconds, and disconnect all the ports. The boot time was always very long.
2. Even thought it supplies power to the cameras, the PoE lights on the ports are not lit.
3. The log is filled with this error, posted every second.
21474345202013-Apr-12 11:40:23Alert%HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_read_mem failed addr 0x12e6 dev_num 0 val 0x0) was detected: POE is Disabled untill Reset 21474345212013-Apr-12 11:40:22Alert%HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_read_mem failed addr 0x139c dev_num 0 val 0x0) was detected: POE is Disabled untill Reset
Occasionally it has his error.
Cisco Switches :: SG300 / Switching Firmware (Active Image)
Apr 16, 2013I have a question regarding SG300 series small business switches.If I switch between the two possible images, will the configuration get lost or is the configuration the same independent of which image I choose?
View 1 Replies View RelatedCisco Switches :: SG300-28 In Boot Loop After Firmware Upgrade
Jun 22, 2012After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process. I have tried loading different versions from the console, but all produce the same error.
Cisco Switches :: SRW2024 / How To Upgrade Boot And Software Via Telnet
Mar 26, 2013I HAD similair problem:[URL](Have ver 1.1) Forgot password. Restored to v1.0.0.86 via telnet Been playing around with telnet AND web based updates Read somewhere else (Web-based ONLY works with IE) (Tried Web-based and keep getting "Copy Failed/Undefined Error" and 0 Bytes transfered) Know to upgrade "Boot" first, then "Software Image" THEN reboot
Tried telnet (not through web-based startup) Can get to "lcli" (by Ctrl+Z twice)Retyped Username and Password:
At "console#" tried typing "copy tftp:///srw2024_16_boot-101.rfb boot" didn't work : "Must be valid URL or reserved keyword"
Where am I going wrong?
Dell 5324 - Managed Switches And Port Boot Time
Nov 29, 2012I recently installed a Dell 5324 switch as my main switch and it's my first time using a managed switch at home. One thing I've seen as an issue in a corporate environment, and now here, is that managed switches tend to take a bit longer for a port to be active. Ex: a PC is turned off, I turn it on but if the PC boots up very fast the port may not be ready. All mounts fail. This is the issue I am facing with my HTPC. It runs Linux and has a SSD, and it has no UEFI bios to slow it down (which is good, I hate UEFI for that) so it's up and running within 5-10 seconds of pushing the power button. The network mappings fail because the port is not ready by the time it gets to the script that mounts everything.
View 8 Replies View RelatedCisco Switches :: SG 200-26 Switch Canon Image Runners Can't Scan To IP Address
Dec 11, 2011I installed an SG 200-26 switch this weekend, and now I have a problem scanning from our Canon Imagerunner printer/scanners to any IP address on our network. It's not a DNS issue as the address book entries contain the destination computer IP address.
View 4 Replies View RelatedCisco Switches :: 2948G-L3 Cannot Load Boot-flash In Loop And No Common Prompt
May 2, 2012i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies View RelatedCisco Switches :: SRW224G4 V1.1 After Power Brake Our Switch Doesn't Boot Anymore
Aug 15, 2012We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies View RelatedCisco Firewall :: ASA5510 Device Manager Image Set But Not A Valid Image File
Feb 9, 2012I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedCisco Switching/Routing :: WS-C3750G-48PS / Unable To Update Boot Path In Stack Switches
Sep 11, 2012I am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not.also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Master switch has new boot path but unable to change in slaves.
View 1 Replies View RelatedCisco Routers :: SRP526W Won't Boot Correct
Nov 15, 2012i have a SRP526W and it won't boot correct, nothing is changed, I just turned it off and changed the place, now it won't boot. The POWER/SYS LED flashes and DSL Data LED is solid green!!
View 1 Replies View RelatedCisco WAN :: Why Does 2811 Routers Boot To ROMmon After Updating IOS
Mar 22, 2012why does my 2811 routers boot to rommon after uploadig IOS c2800nm-ipbasek9-mz.151-4.M1.bin
View 1 Replies View RelatedBelkin Routers :: N750 DB - 5GHz Side Disappears After Boot Up?
Feb 1, 2013I just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
View 3 Replies View Related