Cisco WAN :: 2801 Unable To Boot Image Wrong System Software
Feb 28, 2011
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
View 1 Replies
ADVERTISEMENT
May 27, 2013
i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
View 1 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
Sep 29, 2012
I have a 5010 that simply won't load any system image. Loads the kickstart image just fine, but once at the Switch(boot)# prompt just give me garbage when I enter "load bootflash:n5000-uk9.5.1.3.N2.1b.bin Restarting system.
Loader Version pr-1.3
loader> dirbootflash: lost+found n5000-uk9-kickstart.5.2.1.N1.1b.bin n5000-uk9.5.2.1.N1.1b.bin n5000-uk9-kickstart.5.1.3.N2.1b.bin n5000-uk9.5.1.3.N2.1b.bin
[Code]....
View 1 Replies
View Related
Mar 13, 2011
I have a Cisco 2801, IOS 12.4(24)T2 (C2801-IPBASEK9-M) on a WAN link to another 2801, which appears to be wrongly detecting our cross-site EMC replication traffic as Skype.
I am 100% sure that Skype isn't running on any of our PC's, yet the Skype protocol is by far the highest used out of everything. I have watched these traffic stats late at night when nobody is on the network and when the only traffic is replication, and this is the protocol which is constantly increasing.
If I run 'sh ip nbar port' , Skype isn't listed in the port-map. If I use ? at the end of the command, it lists Skype as option. The 'sh ip nbar protocol-discovery' show the following (among others):
FastEthernet0/1/0
Last clearing of "show ip nbar protocol-discovery" counters 6d10h
Input Output ----- ------ Protocol Packet Count Packet Count Byte Count Byte Count 5min Bit Rate (bps) 5min Bit Rate (bps) 5min Max Bit Rate (bps) 5min Max Bit Rate (bps) ------------------------ ------------------------ ------------------------ skype 76133998 146572068 6167477623 173614718864 0 0 1221000 8973000
EMC have informed me that the port used for replication is 8888, but I can't see how NBAR can think this is Skype.
why NBAR is detecting Skype traffic?!
View 1 Replies
View Related
Feb 27, 2012
I wanna upload ios image of 36mb on a 2801 but I get error not available space. The router already has ios image of 40mb and available space is around 15mb. How to delete existing image and upload the new image?
View 7 Replies
View Related
Mar 17, 2011
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
View 5 Replies
View Related
Aug 27, 2012
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
View 1 Replies
View Related
Dec 30, 2011
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
View 6 Replies
View Related
Apr 29, 2012
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies
View Related
Nov 27, 2011
I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
View 1 Replies
View Related
Dec 29, 2011
I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
View 3 Replies
View Related
May 1, 2011
I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
View 1 Replies
View Related
Oct 24, 2012
I have a Cisco 7204 vxr router that does not have a valid image on the boot flash or on the pcmcia card (disk 2). I tried everything i could to try and get the router to recognize the flash but it keeps giving me a magic card error. I'm losing my mind slowly but surely.
The router boots into Rommon every time and the Rommon options for this router are horrible. No tftpdnld option. Can I get this router to boot from tftp, from Rommon?
View 1 Replies
View Related
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
Nov 1, 2011
I just pulled the AP out of the box and haven't received support contracts yet. I connected the AP to the LAN and added it to my 4402 controller (version 5.2.178.0) with no problems. Once I set it the mode to H-REAP and it rebooted, it went loopy. Actually, it boots up, shows a bunch of debug info, then reboots. The console output is below. I've tried reimaging (image c1140-rcvk9w8-tar.124-21a.JA2.tar) but still have the same problem. I checked and although the controller software is old, the AP is supported.
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
[Code]....
View 7 Replies
View Related
May 13, 2013
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies
View Related
May 18, 2013
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
View 7 Replies
View Related
Jan 25, 2013
How do I add network drivers to a wds boot image on 2003R2. I see that 2008 has the add driver option but that doesn't exist in 2003r2.
View 1 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Jan 22, 2008
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies
View Related
Aug 23, 2010
I have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
View 8 Replies
View Related
Sep 22, 2012
I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
View 1 Replies
View Related
Nov 29, 2012
Cisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies
View Related
Feb 26, 2013
I recently formatted the flash drive of an 1800 router and replaced it with an updated image. However, the new features within the new image aren't reflected in the router. I believe that this is because a reboot would be required for the updates in the new image to be reflected in the router i.e. the image needs to be added to the system. How to get the image to the system without a reboot and if by doing so I would get all the new features from the image.For example, the show version below shows the old image in the system as [code]
View 2 Replies
View Related
Nov 6, 2006
I have a problem on a 1131ag Access point on recycle it stops and makes me maunually type BOOT at the ap: prompt
----------VVVVVVVVVVVVV----------------
ap: Xmodem file system is available.
flashfs[0]: 282 files, 13 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
I have already performed the ap: set BOOT etc commands a dozen times with the same results. It says: The system is not configured to boot automatically.
I've been trying to get this one going for 4 months now..it was knocked out during a power outage while upgrading it.
View 6 Replies
View Related
Apr 8, 2013
We have a N5K-C50510P-BF. When these nexus starts that didn't booting any further than the kickstart. Here's the boot sequence log
User break into bootloader
Loader Version pr-1.3
loader>
[Code]....
View 0 Replies
View Related
Jul 17, 2012
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
View 3 Replies
View Related
Feb 25, 2013
I have a Cisco switch 3400-ME, it's running IOS1.bin file. Now i want to change the running IOS to IOS0.bin.I entered 2 commands:
boot system flash:dir1/IOS0.bin
boot system flash:dir1/IOS1.bin
But when i show running config, it has no any boot system commands. when i relboot that switch?
View 2 Replies
View Related
Dec 13, 2011
boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin We have two stack of 3750 switches. When I enter above command getting below mentioned error, two images are showing switch 1, but one image only showing in switch 2, i.e 1st image in show boot command.
%Command to set boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin on switch=2 failed
View 5 Replies
View Related
Sep 7, 2011
I would like to upgrade rommon on my Cisco 2801 but this is what I get: [code]The router stops here and I am forced to power off and on again and the upgrade does not succeed.
View 10 Replies
View Related
Jan 12, 2013
I have an issue where I can get traffic to pass from HDQ to two branch offices over our ipsec/gre tunnels even though the tunnels appear to be UP. The HDQ is a 2811, branch is a home office using an 871W and branch runs a 2801 router. I initially had HDQ working fine with the 871W but when I configured branch2 (2801), they both broke. The tunnels appear to be up but traffic is not routing across them. The two 2801 routers run 12.4 (c2800nm-adventerprisek9-mz.124-24.T2.bin). These are gre over ipsec tunnels. Currently traffic flows over an exsting MPLS network that we are getting away from due to cost. As soon as I change the routes to point to the Tunnels, it breaks. Traffic doesn't appear to pass through the tunnel. I have attached my sanitized configs.
HDQ#sh crypto sessCrypto session current status
Interface: FastEthernet0/1Session status: UP-ACTIVEPeer: 205.205.205.21 port 500 IKE SA: local 204.204.204.66/500 remote 205.205.205.21/500 Active IPSEC FLOW: permit 47 0.0.0.0/0.0.0.0 0.0.0.0/0.0.0.0 Active SAs: 4, origin: crypto map IPSEC FLOW:
[Code]....
View 3 Replies
View Related
Jul 4, 2011
Getting message, cannot open "flash:" on 1841 evdo router, how do I reinstall flash? I am currently consoled into the router, the prompt is coming up as rommon 1>
View 1 Replies
View Related
