I have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
My ISP recently upgraded my line to ADSL2+. I am still only getting 1.36Mbps download speed across WiFi but if I connect my laptop to the router with ethernet cable I get 8.59Mbps. Why is the router slowing down my connection so much?
View 1 Replies View RelatedHave noticed that wireless download speed deteriorated since they installed this?
Mine seems horrendously slower.
I'm having issues with the wireless speed of my WAG160N. I'm using WPA2/AES, firmware: V2.00.20. The wireless connection signal is very good and the speed shows 130 Mbit/s.
On a wired connection when testing with numion.com I get 6 Mbit/s which is my DSL speed (this is great). On the wireless connection I get max 1,8 Mbit.
I am using linksys cisco wag120n adsl2 modem router.When I start the router the internet speed seems great but after some time the speed drops miserably. When I again restart the router the speed seems great for few mins but again drops after sometime.It happens in both LAN and wireless mode.The firmware version of the router is 1.00.16
I was going through the problems posted by some other user but observed that cisco people are not heraing to them.Seems made a mistake by associating with cisco product.This is the worst router I have ever used.The wireless also gets disconnected abruptly.Next time I'll avoid cisco.Cisco is all about stone age products and zero customer care.
I have wag160nv2 linksys, and way that i ca connect it to wireless router and take a wireless internet from it?
View 2 Replies View RelatedI have the above router, but I have noticed that the USB Transfer speed is very poor. I have a WD External HD plugged into the router and id i transfer filed from my server which is hardwired to the router I only get a transfer speed of about 2.5MB/s.
For a USB device I was kind of thinking I would be getting a minumm of atleast 50-60MB/s.
I have a E3000 with newest firmware that has a VOIP by Velcom. It's a Grand stream HT–286.My device is working perfectly with the router. Can call and recieve calls. the caller ID (Name and number that appears is accurate). The only problem is the caller ID's time and date are always wrong.When I unplug device, it goes back to Jan 1 and time 12:00am.Any call I then get is wrong.
In the router, I've enabled SIP ALG. And the firewall is only filtering ident (port 113) and Anonymous Internet requests.The device has a hard coded internal IP (192.168.123.110). and I reserve the IP using mac filtering.The device has an administration page that is unavailable to users as it's locked by a password. On this page has an NTP server setting that the device uses to get it's time/date.I see on the information page of the device that iot's registered to a sip server.The company is saying that it's a firewall issue. I'm not too sure how to proceed.
Recently I have changed my ISP and switched from an ADSL (4Mbps) connection to a faster fiber connection (100Mbps). I own an WAG120N which after firmware 1.00.12 (currently installed on the device is 1.00.16) should allow LAN1 to be used as WLAN. This is true and I can use it to connect to the new provider.
However the speed when using LAN1 as WLAN on WAG120N is very slow: download 20Mbps and upload 10Mbps. The LED on LAN1 is orange instead of green as before. I have tested the ISP connection with an WRT160NL and the speeds are much faster: download/upload 87Mbps
Ive bought recently WAG160n and Ive watched that I have problem with slow speed of WiFi. On LAN cable its ok. Internet provider gives my up 20Mb/sec. download and up to 1Mb/ses. upload. Ive visited
[code]....
I add, that my previous router: WAG200G on this same line gives me 14-16 Mb/sec. download on WiFi. Why upload speed is ok, but download not?
How can I turn off the wi-fi on WAG160Nv2?Upon entering it I find no option that says Disable Wireless.
View 5 Replies View RelatedI have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
To connect WAG160N to a Dell switch 5224 do I need a cross cable or a simple one? Do I need to use port 1 of WAG160N or any port ?
View 2 Replies View Relatedthe other day i set up a new internet connection and to set it up they sent me a WAG160Nv2 modem router and after hours of trying to get it working the technical support guy told me it cant be set up until the dsl led comes on, so what it being off means/how to get it to turn on?
View 2 Replies View RelatedThe only thing I notice now is that channels 12 and 13 do not work properly. Setting the router to channels 12 and 13 basically sets the channel to something in the 1 - 11 range as seen by inSSIDer. This could be because the firmware I installed is the US version, which only has channels 1 - 11, but the EU version has channels 1 - 13. Normally this wouldn't be a problem but because there are a lot of wireless signals where I live, channels 1 - 11 are quite congested, so channel 13 was quite useful to me.I don't suppose anyone has a EU version of the WAG160NV2 2.00.17 firmware do they?Channels 12 and 13 worked fine with the EU version of the WAG160NV2 2.00.20 firmware but of course only at 2Mbps.
View 5 Replies View RelatedI want to control my homes X10 Devices (lights on/off, close garage door, etc) using an iPhone application.
View 7 Replies View RelatedSignal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers.. Lan line works fine for me with no issues
I will update the firmware and try that as it seems i am running old firmware V2.00.13
my WAG160Nv2 drops the connection each day at the same hour (4:20pm to 4:40pm aprox.)I think that is because my ISP don't give me a static IP address and the connection must dropped once a day. in my old router I could put the time for the drop. I don't find something similar in the WAG160Nv2.
View 2 Replies View RelatedI have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies View RelatedConnect WAG160Nv2 with another modem / router Wi-Fi?
View 2 Replies View RelatedIs there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
Here's the problem : I've installed this router to a friends of mine home and since then in the gam "Warhammer 40000 Dawn of War 2 : Retribution" they can't play together (they're connected via WAN) in a 2v2 without getting disconnected FROM THE INTERNET (not only the game, the whole ADSL line collapse after an over 3000ms of ping for few sec.). Same thing if one of them try to make a 3v3 (so 1 with the WAG160Nv2, and 2 other persons via internet.), 3000pings for few sec and then they get DC from the internet, after few sec the router gets back online but still they can't play together or make a 3v3.
View 1 Replies View RelatedWe have a SBS 2003 server with two NIC's, one for the internal LAN and the other connecting to the WAG160Nv2 that is hooked up to the internet.The internal LAN clients are all getting IP addresses from the DHCP server in the SBS Server (192.168.16.XXX). The DHCP server is sat at 192.168.16.2.The only thing connected to the LAN ports on the WAG160Nv2 is the Internet facing NIC from the server.What I want to do is to get the WAG160Nv2 to give IP addresses to Wireless connections going through the router, can I configure the DHCP relay option on the WAG160Nv2 to do this, I have looked at the DHCP relay option but it doesn't seem to work, my wireless connections are getting private 169.254.xxx.xxx addresses.Also is there anything I can do to make the wireless more Apple friendly, iPhones and iPads drop of the wireless frequently, that's why I trying a different approach.
View 1 Replies View Related( Home Cisco router WAG160Nv2, Windows Vista)Who is the network administrator on my home network and which device is involved: Windows Vista, Cisco network magic pro ? ; the Cisco router modem with WLAN ?The wireless MAC filter on the modem is disabled.The access is denied to my WLAN and the only one from which I get signals from the neighborhood. My main laptop has access to the network only over the Ethernet, but not over WLAN.My second laptop has access to this network over the Ethernet and WLAN .
View 2 Replies View RelatedSince i used this new modem ruoter, on facebook game Cafe WORLD i can't send requests or gifts to neighbors/friends. when the window pops out there's no friend list. it's just a blank space. also when i click the share button only a blank page pops out. i tried it in 3 different pc here @ home in different browser but still had no luck...i tried it on my bf's place and it works so i guess there's a prob with my connection. and sometimes i have the internet access but i couldn't navigate in any website only for chatting.
View 3 Replies View RelatedDoes WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies View RelatedI have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies View RelatedI have a Netgear 600 dual band router connected to a DOCIS 3.0 cable modem with a 25mps internet connection from my ISP, should be fast right? When I run a speed test on my comp I get 10-13 mbps download on average. Here's the issue, upon visiting my mothers house and running the same speed test I got very similar results. She is running a Lynksys G router on a DOCIS 2.0 cable modem with 12mps connection. My question is, how can this be so, am I at the limits of my comps g network card? as a disclaimer I would like to note I am connected to the G band on both routers.
View 1 Replies View RelatedI have FiOS and their supplied wireless router Actiontec #MI424WR. I have home theater equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. I have one of the LAN outputs on the Actiontec feeding the Linksys input and Wi-Fi turned off on the Actiontec. This is working good for my wireless home theater equipment but I am having problems with my wired speed. It has gone from averaging anywhere from 20 to 30 mbps on numerous test sites when plugged into the Actiontec to averaging around 10 mbps when plugged into the Linksys.
1) Is my wireless N speed going to top out at 10mbps or less since that is all the router is showing on wired? Shouldn�t N be broadcasting a faster speed if given the ability?
2) I have my computer currently plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get the speed higher on the Linksys, a setting I can change? Will I have to plug the computer back into the Actiontec to get the higher speed and then move it every time I may need to make a change to the Linksys?