Linksys Cable / DSL :: WAG160Nv2 - Access To WLAN Denied By Network Administrator
Apr 22, 2011
( Home Cisco router WAG160Nv2, Windows Vista)Who is the network administrator on my home network and which device is involved: Windows Vista, Cisco network magic pro ? ; the Cisco router modem with WLAN ?The wireless MAC filter on the modem is disabled.The access is denied to my WLAN and the only one from which I get signals from the neighborhood. My main laptop has access to the network only over the Ethernet, but not over WLAN.My second laptop has access to this network over the Ethernet and WLAN .
View 2 Replies
ADVERTISEMENT
Jun 24, 2011
I was changing the computer name on a group of networked computers but forgot to go to - Manage - Users - Administrator and set a password. I accessed Computer - System Properties - Clicked the "Change" button for "To rename this computer, click Change" and selected the "Workgroup" as opposed to the "Domain" option. When I restarted the computer the computer will not allow me to enter the administrator password to allow me access the computer.
View 2 Replies
View Related
Apr 14, 2013
All I want to do is to share a couple of Folders, My Documents and Downloads, between two PC's on a Workgroup network.Networking is not my strongest point but up until now I have managed quite successfully.The setup is :-
1st PC is Mike-Laptoppc is on a Wireless connection to an ADSL+2 router/modem.
2nd PC is a Desktop Alexs-PC connected via cable to the same router/modem
I can share all the shared folders from the Desktop to the Laptop, but I can only share Media streaming on the Desktop from the Laptop, so I know there is a connection between the two computers. I have now turned off Media streaming to concentrate on just folder sharing.Whenever I try to access the Laptop from the Desktop I get an " Access Denied you do not have permission contact your administrator " box on the desktop.
View 6 Replies
View Related
May 20, 2012
I have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
View 8 Replies
View Related
Sep 30, 2012
To connect WAG160N to a Dell switch 5224 do I need a cross cable or a simple one? Do I need to use port 1 of WAG160N or any port ?
View 2 Replies
View Related
Mar 23, 2012
How can I turn off the wi-fi on WAG160Nv2?Upon entering it I find no option that says Disable Wireless.
View 5 Replies
View Related
Nov 11, 2011
the other day i set up a new internet connection and to set it up they sent me a WAG160Nv2 modem router and after hours of trying to get it working the technical support guy told me it cant be set up until the dsl led comes on, so what it being off means/how to get it to turn on?
View 2 Replies
View Related
Jun 27, 2011
The only thing I notice now is that channels 12 and 13 do not work properly. Setting the router to channels 12 and 13 basically sets the channel to something in the 1 - 11 range as seen by inSSIDer. This could be because the firmware I installed is the US version, which only has channels 1 - 11, but the EU version has channels 1 - 13. Normally this wouldn't be a problem but because there are a lot of wireless signals where I live, channels 1 - 11 are quite congested, so channel 13 was quite useful to me.I don't suppose anyone has a EU version of the WAG160NV2 2.00.17 firmware do they?Channels 12 and 13 worked fine with the EU version of the WAG160NV2 2.00.20 firmware but of course only at 2Mbps.
View 5 Replies
View Related
Feb 19, 2012
I want to control my homes X10 Devices (lights on/off, close garage door, etc) using an iPhone application.
View 7 Replies
View Related
Mar 20, 2011
Signal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers.. Lan line works fine for me with no issues
I will update the firmware and try that as it seems i am running old firmware V2.00.13
View 4 Replies
View Related
Jun 8, 2012
my WAG160Nv2 drops the connection each day at the same hour (4:20pm to 4:40pm aprox.)I think that is because my ISP don't give me a static IP address and the connection must dropped once a day. in my old router I could put the time for the drop. I don't find something similar in the WAG160Nv2.
View 2 Replies
View Related
Jun 12, 2012
I have wag160nv2 linksys, and way that i ca connect it to wireless router and take a wireless internet from it?
View 2 Replies
View Related
Apr 3, 2011
Have noticed that wireless download speed deteriorated since they installed this?
Mine seems horrendously slower.
View 1 Replies
View Related
Jul 8, 2011
I have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies
View Related
Mar 25, 2012
My ISP recently upgraded my line to ADSL2+. I am still only getting 1.36Mbps download speed across WiFi but if I connect my laptop to the router with ethernet cable I get 8.59Mbps. Why is the router slowing down my connection so much?
View 1 Replies
View Related
May 14, 2011
Connect WAG160Nv2 with another modem / router Wi-Fi?
View 2 Replies
View Related
Apr 3, 2011
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
View 1 Replies
View Related
Mar 21, 2011
Here's the problem : I've installed this router to a friends of mine home and since then in the gam "Warhammer 40000 Dawn of War 2 : Retribution" they can't play together (they're connected via WAN) in a 2v2 without getting disconnected FROM THE INTERNET (not only the game, the whole ADSL line collapse after an over 3000ms of ping for few sec.). Same thing if one of them try to make a 3v3 (so 1 with the WAG160Nv2, and 2 other persons via internet.), 3000pings for few sec and then they get DC from the internet, after few sec the router gets back online but still they can't play together or make a 3v3.
View 1 Replies
View Related
Dec 13, 2012
We have a SBS 2003 server with two NIC's, one for the internal LAN and the other connecting to the WAG160Nv2 that is hooked up to the internet.The internal LAN clients are all getting IP addresses from the DHCP server in the SBS Server (192.168.16.XXX). The DHCP server is sat at 192.168.16.2.The only thing connected to the LAN ports on the WAG160Nv2 is the Internet facing NIC from the server.What I want to do is to get the WAG160Nv2 to give IP addresses to Wireless connections going through the router, can I configure the DHCP relay option on the WAG160Nv2 to do this, I have looked at the DHCP relay option but it doesn't seem to work, my wireless connections are getting private 169.254.xxx.xxx addresses.Also is there anything I can do to make the wireless more Apple friendly, iPhones and iPads drop of the wireless frequently, that's why I trying a different approach.
View 1 Replies
View Related
Jun 27, 2011
Since i used this new modem ruoter, on facebook game Cafe WORLD i can't send requests or gifts to neighbors/friends. when the window pops out there's no friend list. it's just a blank space. also when i click the share button only a blank page pops out. i tried it in 3 different pc here @ home in different browser but still had no luck...i tried it on my bf's place and it works so i guess there's a prob with my connection. and sometimes i have the internet access but i couldn't navigate in any website only for chatting.
View 3 Replies
View Related
Feb 3, 2011
Does WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies
View Related
Aug 23, 2010
I have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
View 8 Replies
View Related
May 14, 2012
Network access denied for a particular folder
View 1 Replies
View Related
Oct 27, 2011
I use the WAP610N as an Accesspoint for only an small Mobilephone to WLAN Printer Network.My big Problem is that i have therefore no DHCP Server in this special small WLAN Network.And now i need an own DHCP Server from the Accesspoint side because otherwise i must use static IP Adresses in all Mobilephones to connect with the WLAN Network .In the WAP610 unfortunately there is only the choose between static IP Adress and IP Adress FROM an existing DHCP server .
View 2 Replies
View Related
May 7, 2013
I have a EA6500 with a hard drive connected to the USB port. When I try to copy a file to the drive VIA the network folder on my computer it says "Destination Folder Access Denied, You Need Permision To Perform This Action". I used to be able to copy files to the drive so I am sure it is just a setting on the router or something.
View 5 Replies
View Related
Nov 7, 2009
I just bought a WMP600N adaptor and although windows 7 recognizes it I would like to install the official drivers from Linksys. When I try to update the drivers that I downloaded from the linksys website I het an access denied error. I am logged in as the administrator. I have already tried uninstalling the default drivers, but still I get the access denied error. I even tried the windows safe mode and still got the access denied error.
With the default windows 7 drivers the connection is quite poor. how I can install the official windows 7 drivers?
View 8 Replies
View Related
Jan 31, 2011
We have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
View 3 Replies
View Related
Jan 16, 2012
Recently I have changed my ISP and switched from an ADSL (4Mbps) connection to a faster fiber connection (100Mbps). I own an WAG120N which after firmware 1.00.12 (currently installed on the device is 1.00.16) should allow LAN1 to be used as WLAN. This is true and I can use it to connect to the new provider.
However the speed when using LAN1 as WLAN on WAG120N is very slow: download 20Mbps and upload 10Mbps. The LED on LAN1 is orange instead of green as before. I have tested the ISP connection with an WRT160NL and the speeds are much faster: download/upload 87Mbps
View 3 Replies
View Related
Aug 3, 2012
It has been 4 months my Router " Wag 120n ". The Router Gives Me A yellow Sign on the network Icon Sying " No network Access " and the wireless Led is blinking with 1 sec interval So
- I cant open Router's Home Page
- there is No ping to 192.168.1.1 " General Failure or Host unreachable " response
- The Only way to get connected again is to replug the router from electricity , it works normally for 5 min and the Yellow Sign shows up again
the Solutions I Tried to fix that up :-
1) Hard reset the 30/30/15 reset
2) Firmware re-flashing
3) Trying an old firmware 1.0.0.12 instead of 1.0.0.16
but nothing of those worked the Only thing that worked for like 20 min the firmware upgrade but after that the problem came up again the problem happens to all Computers on the network wired or on wireless happens on all kind of operations systems win7, xp, vista, (Android for mobiles).
View 3 Replies
View Related
Apr 11, 2012
Here's the deal. My internet provider provided me with a shitty router with a lot of settings locked. I can't change DHCP settings or add custom static IP addresses. This sucks. The wireless function on it sucks also.I added an extra router to the network so I have good Wifi in my living room. I turned off the NAT, firewall and DHCP on that one, so it's a simple switch with a wireless access point now.Now here's the deal. The DHCP server of the provider's router hands out IP's from 192.168.2.1 to 192.168.2.253 (192.168.2.254 is the router's own IP address).I gave the added switch/access point the IP address 192.168.1.1 in its own settings. The original router doesn't 'see' the switch now anymore because it's out of the DHCP's range. When I gave it an IP address within the DHCP's IP range, I got all kinds of conflicts (as expected).
I guess this is a solution since it works, but I'm open to other suggestions since it doesn't seem to be the best way of doing things. Besides, I can't access the access point's web interface anymore since it doesn't have an IP address within the network now. It isn't important because I don't need to change any settings anymore, but still.I'm going to add a second wireless router to replace the built-in wireless function of the provider's router. For some reason it sees its own wireless network as a separate network or something. When I roam from the new access point wifi to the provider router's wifi, everything gets confused because it tries to give the laptop a new IP address.
View 4 Replies
View Related
Apr 2, 2011
NETWORK CONNECTION PROBLEMPOPUP ERROR states"\<name> is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Access denied."When trying to View the two PCs through My Network Places> View workgroup Computers in MSHOME?I was able to map the shared folder manually.
View 1 Replies
View Related
Jan 3, 2011
I have a computer with windows 2003 server installed on it. There is one shared folder. The computer's name is SERVER. The shared folder's name is OFFICE.Whenever I type \SERVEROFFICE in a windows explorer window, I get a pop up window with a message that says that Windows does not find \SERVEROFFICE.I mean, I should be able to see the folder in this way because this OFFICE folder is shared and I am doing this from the same computer and not from another computer in the LAN.
View 3 Replies
View Related
May 28, 2012
I'm trying to solve a disastrous networking (via workgroup nightmare) and I cannot enable the DNS Client on my Windows 7 PC. I go to cntrl panel, admin services, dns client, and try to change it to automatic and it says "access is denied"
View 1 Replies
View Related
