Signal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers.. Lan line works fine for me with no issues
I will update the firmware and try that as it seems i am running old firmware V2.00.13
How can I turn off the wi-fi on WAG160Nv2?Upon entering it I find no option that says Disable Wireless.
View 5 Replies View RelatedI have d-link wireless router which is connected to the internet, also I have Linksys (WAG160Nv2) which i want to use it as access point by link it to D-link router using ethernet cable in order to use the wireless internet. D-link router settings shown below
I changed the settings of linksys router as shown below
To connect WAG160N to a Dell switch 5224 do I need a cross cable or a simple one? Do I need to use port 1 of WAG160N or any port ?
View 2 Replies View Relatedthe other day i set up a new internet connection and to set it up they sent me a WAG160Nv2 modem router and after hours of trying to get it working the technical support guy told me it cant be set up until the dsl led comes on, so what it being off means/how to get it to turn on?
View 2 Replies View RelatedThe only thing I notice now is that channels 12 and 13 do not work properly. Setting the router to channels 12 and 13 basically sets the channel to something in the 1 - 11 range as seen by inSSIDer. This could be because the firmware I installed is the US version, which only has channels 1 - 11, but the EU version has channels 1 - 13. Normally this wouldn't be a problem but because there are a lot of wireless signals where I live, channels 1 - 11 are quite congested, so channel 13 was quite useful to me.I don't suppose anyone has a EU version of the WAG160NV2 2.00.17 firmware do they?Channels 12 and 13 worked fine with the EU version of the WAG160NV2 2.00.20 firmware but of course only at 2Mbps.
View 5 Replies View RelatedI want to control my homes X10 Devices (lights on/off, close garage door, etc) using an iPhone application.
View 7 Replies View Relatedmy WAG160Nv2 drops the connection each day at the same hour (4:20pm to 4:40pm aprox.)I think that is because my ISP don't give me a static IP address and the connection must dropped once a day. in my old router I could put the time for the drop. I don't find something similar in the WAG160Nv2.
View 2 Replies View RelatedI have wag160nv2 linksys, and way that i ca connect it to wireless router and take a wireless internet from it?
View 2 Replies View RelatedHave noticed that wireless download speed deteriorated since they installed this?
Mine seems horrendously slower.
I have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies View RelatedMy ISP recently upgraded my line to ADSL2+. I am still only getting 1.36Mbps download speed across WiFi but if I connect my laptop to the router with ethernet cable I get 8.59Mbps. Why is the router slowing down my connection so much?
View 1 Replies View RelatedConnect WAG160Nv2 with another modem / router Wi-Fi?
View 2 Replies View RelatedIs there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
Here's the problem : I've installed this router to a friends of mine home and since then in the gam "Warhammer 40000 Dawn of War 2 : Retribution" they can't play together (they're connected via WAN) in a 2v2 without getting disconnected FROM THE INTERNET (not only the game, the whole ADSL line collapse after an over 3000ms of ping for few sec.). Same thing if one of them try to make a 3v3 (so 1 with the WAG160Nv2, and 2 other persons via internet.), 3000pings for few sec and then they get DC from the internet, after few sec the router gets back online but still they can't play together or make a 3v3.
View 1 Replies View RelatedWe have a SBS 2003 server with two NIC's, one for the internal LAN and the other connecting to the WAG160Nv2 that is hooked up to the internet.The internal LAN clients are all getting IP addresses from the DHCP server in the SBS Server (192.168.16.XXX). The DHCP server is sat at 192.168.16.2.The only thing connected to the LAN ports on the WAG160Nv2 is the Internet facing NIC from the server.What I want to do is to get the WAG160Nv2 to give IP addresses to Wireless connections going through the router, can I configure the DHCP relay option on the WAG160Nv2 to do this, I have looked at the DHCP relay option but it doesn't seem to work, my wireless connections are getting private 169.254.xxx.xxx addresses.Also is there anything I can do to make the wireless more Apple friendly, iPhones and iPads drop of the wireless frequently, that's why I trying a different approach.
View 1 Replies View Related( Home Cisco router WAG160Nv2, Windows Vista)Who is the network administrator on my home network and which device is involved: Windows Vista, Cisco network magic pro ? ; the Cisco router modem with WLAN ?The wireless MAC filter on the modem is disabled.The access is denied to my WLAN and the only one from which I get signals from the neighborhood. My main laptop has access to the network only over the Ethernet, but not over WLAN.My second laptop has access to this network over the Ethernet and WLAN .
View 2 Replies View RelatedSince i used this new modem ruoter, on facebook game Cafe WORLD i can't send requests or gifts to neighbors/friends. when the window pops out there's no friend list. it's just a blank space. also when i click the share button only a blank page pops out. i tried it in 3 different pc here @ home in different browser but still had no luck...i tried it on my bf's place and it works so i guess there's a prob with my connection. and sometimes i have the internet access but i couldn't navigate in any website only for chatting.
View 3 Replies View RelatedDoes WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies View RelatedI have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
I have a WAG120N annex A on firmware v1.00.16, which appears to be working fine with a variety of devices (iPhone, squeezebox, vista pc, linux pc, android) via wireless and ethernet.
However, my Macbook 4,1 running OSX 10.6.6 keeps losing internet connection regularly and the only way to get it back is to turn the airport off and then on again. It's very odd, appears to still be connected to the router but just can't access the internet!
The Airport version and driver is: AirPort Extreme (0x14E4, 0x88) Firmware Version: Broadcom BCM43xx 1.0 (5.10.131.36.1)
I recently Installed AVG 2011 and AVG PC tune-up 2011. When i just start my computer the internet is working fine, but after a open my game Flyff, The internet is still connected but cannot use it.
View 2 Replies View Related I purchased this router and a Motorola Surfboard SB5101U for my home network. My current set up at home for devices connected to router are as follows:
2 Macs and 2 iphones - Wireless
2 Directv boxes, 2 blu-ray players and xbox360, Ethernet cabling.
The issue I am having is that everyday at-least 7-8+ times my internet will just stop coming through. I never lose connection to the router it's self. But I cannot load webpages/content on any of my devices. They always show as being connected fine to the router though. I have attempted to call Cox cable, my ISP, to resolve the issue. And I am always told that everything looks fine on their end and that the issue must lie with the connection between the Modem and router. The rep then walks me through a complete reboot of both router & modem and of course, the issue is resolved 100% of the time. I am trying to fix the issue my self to avoid a $50 service call fee from Cox which could still not fix any issues at all. Since I have done some searching and found some advice on making changes to the configuration of the router. But time after time I continue to get the same issue.
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI have an RV180W Wireless-N with firmware# 1.0.1.9 The problem is that any Macintosh computer will not work with the wireless network.The problem is consistent with several MacBook laptops, running Leopard, Snow Leopard and Mountain Lion.The MacBook connects with the wireless network and obtains an IP address.However when the MacBook tries to access a web page, it fails loads.Accessing LAN assets like network volumes and printers works fine.All mobile devices, such as iPhones, iPods and iPads work fine.I have tried numerous wireless settings on the router and the MacBooks and nothing works.The problem happens regardless of what kind of wireless security is present.There is not MAC filter.
View 1 Replies View RelatedLog enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View RelatedI have the WCG200 and it has been working fine with my Comcast service for the last 4 years with no issues, either wired or wireless. Starting about a week ago, I have been having a lot of trouble with my wireless. I am on Firmware Version: 2.0.3.9.31-1023 and my ISP is Comcast. I have tried calling Comcast to see if there is a firmware update but that phone call usually doesn't go very far.
View 8 Replies View RelatedI just bought a macbook and want to connect with my WAG320N. I have no problem to connect on 54mbs what tells me that I'm on Wifi G. The settings in my router was on b/g/n so I changed it to just N but then it won't connect. I don't get error or nothing. I just doesn't connect. I tried all different kind of settings but no luck.
View 8 Replies View Relatedwhat do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View RelatedI have problems to make a PPTP vpn to my M0n0wall. PPTP passthrough is enabled, port 1723 TCP ist forwarded to M0n0walls WAN Interface. Rules on the M0n0wall are set correctly. It seems that the Linksys has problems with GRE 47 protocol routing. Does a newer model (WAG120N or WAG320N) work with PPTP passthrough?
View 5 Replies View Relatedi have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedLike the title says, the wifi on my wag120n stopped working. It happened suddenly, nothing was changed in the settings. It stopped showing when i'm searching for wireless connections (SSID is still enabled).
View 3 Replies View RelatedI have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.
View 2 Replies View Related