I have problems to make a PPTP vpn to my M0n0wall. PPTP passthrough is enabled, port 1723 TCP ist forwarded to M0n0walls WAN Interface. Rules on the M0n0wall are set correctly. It seems that the Linksys has problems with GRE 47 protocol routing. Does a newer model (WAG120N or WAG320N) work with PPTP passthrough?
View 5 RepliesI would like to know how to properly setup my old wag354g as a wireless ap. should i select from basic setup as "bridge only" or the "rfc bridge"?
wag354g will be connected by wire and supply wireless on laptops with b/g.
I have a WAG354G that i would like to use to extend the range of my WiFi. First Question is - is it possible, and the second is how do i do it?
View 3 Replies View RelatedI have WAG354G wireless router and would like to upgrade the firmware on it, I believe it is version 1.There's two firmware downloads to choose from: Annex A and Annex B.What is the difference between the two?
View 9 Replies View RelatedI'm trying to access a machine via pptp through a new WAG320n without any success. PPTP Passthrough is enabled i've opened port 1723 TCP pointing to my machines ip-adress but i can't get the connection working.
View 9 Replies View RelatedI have a remote location that has a Linksys/Cisco RV042 router [URL] that allows PPTP connections based on username and password combinations. There are no intermediary routers between this device and the internet - only a DSL modem. A secondary WAN connection is not present.
I am able to dial into this VPN using the Windows XP and Windows 7 dialers from any of my local free-wifi locations(e.g. Starbucks). I WAS able to connect to this VPN connection from my house when my home router was a Buffalo brand router.
I have replaced the Buffalo router with a 2620(non-XM) that is connected in ROaS fashion to a 2950 switch. I need some guidance on what in my config is not allowing me to connect to this remote site.
Home network info: Local subnets : 192.168.x.x
Remote network info: Local subnet : 10.214.x.x
The Windows XP dialer client indicates that the username and password challenge is where the connection fails. It ultimately gives me the error code 619. I have performed a Wireshark packet capture of an attempt to connect from ip 192.168.10.11. This packet capture shows multiple "Configuration Request" packets being exchanged between the two endpoints, but does not ever show an exchange of authentication.
My nat translation table shows an entry for both a GRE tunnel as well as port 1723 between 192.168.10.11 and the WAN port of the RV042 when attempting to establish this VPN.
I have attached my 2620 configuration for your review.
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI have a Cisco 877 router and I configured it to act as a VPN server, supporting both PPTP and L2TP VPNs. I can succesfully connect to it from Windows computers using the built-in VPN software.There is only one problem: when using a PPTP VPN, encryption doesn't work. If I configure the client to require encryption (default setting), the connection fails with an error about the remote endpoint not supporting it. If I remove the encryption requirement, the connection succeeds. I've also tried tweaking the encryption settings (40/128 bits), but this didn't work either. [code]
The router's IOS version is 15, and it fully supports encryption. The strangest thing is, encryption is actually required in the router config; but not only the router doesn't seem to offer it... it also accepts unencrypted connections, which it shouldn't. It's like the ppp encrypt mppe auto required command is completely ignored.
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
I have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
RV082 Firmware Version 2.0.2.01-tmRV082 Firmware Version 2.0.2.01-tm
View 1 Replies View RelatedI possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies View RelatedRegion : Hongkong
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_121225
Even I have upgraded to the newest firmware for WDR-4300, it still not allowed me to connect to a windows PPTP VPN. It worked when I changed to use my old router. On the other hand, when I turned the hardware NAT, I found that the Cisco VPN connection would be dropped after I used for a few minutes. Similarly, it worked when I changed to use my previous old router.
Log enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View RelatedI have the WCG200 and it has been working fine with my Comcast service for the last 4 years with no issues, either wired or wireless. Starting about a week ago, I have been having a lot of trouble with my wireless. I am on Firmware Version: 2.0.3.9.31-1023 and my ISP is Comcast. I have tried calling Comcast to see if there is a firmware update but that phone call usually doesn't go very far.
View 8 Replies View RelatedI just bought a macbook and want to connect with my WAG320N. I have no problem to connect on 54mbs what tells me that I'm on Wifi G. The settings in my router was on b/g/n so I changed it to just N but then it won't connect. I don't get error or nothing. I just doesn't connect. I tried all different kind of settings but no luck.
View 8 Replies View Relatedwhat do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View Relatedi have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedLike the title says, the wifi on my wag120n stopped working. It happened suddenly, nothing was changed in the settings. It stopped showing when i'm searching for wireless connections (SSID is still enabled).
View 3 Replies View RelatedI have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.
View 2 Replies View RelatedI'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.
Signal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers.. Lan line works fine for me with no issues
I will update the firmware and try that as it seems i am running old firmware V2.00.13
I have got a Linksys @ Home HG200 V2 G Gateway. I am trying to setup port fowarding but its not working. I have gone onto the routers port forwarding setup page filled it out but the port is still closed.
View 4 Replies View RelatedToday i brought Linksys X3000 and that came with old firmware version (1.0.01). i need new version (1.0.03) Annex A firmware but support page not working.
Support Page is not working: [URL]
I have a Linksys x2000 and have been using it successfully on DSL with a local ISP. I recently changed to Century Link and now I can't connect to the internet (Century Link). If I change the UserId and Password from my Century Link values back to my old ISP values, I can connect to my old ISP. Century Link tells me they have my account active with the X2000 and Century Link.
View 2 Replies View RelatedI have had a WAG320N running problem free for approx 2 months, in that time I've upgraded the firmware 1.00.12 with no issues and has run fine for a month after upgrade. I have 3 laptops connected wirelessly and 2 pc's running wired (through homeplug system) plus TV, PS3 and ipods, all have run without issues.
All of a sudden 2 days ago all wireless connectivity stopped? SSID is still broadcasting and viewable but I can no longer connect with any computer or device. Wired connectivity is working fine.
I've checked security settings, turned off encryption, reset factory defaults, re-downloaded latest firmware and reflashed with no luck. As I said wirless stopped working all of a sudden with no changes to settings.
I purchased wag 200g from dubai more than a year ago. When i tried installing the power socket never worked and till date I never got a solution for this. At present I do not have any documents relafinding a cisco authorised service center in India but in vainted to this product but this issue could not be solved by any computer service center.
View 1 Replies View RelatedMy WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.
View 3 Replies View RelatedI have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies View RelatedRunning Firmware v. 1.00.19 here, which I reckon is the most recent version.
My network consists of two Macbooks, an iMac and two iPhones. It utilizes WAP2 encryption and all devices are well within range, the environment being free of interferences from any other WiFi signals (this is a rural area).
My problem: Bonjour networking stops working after a few minutes or hours. When the problem appears, WIRED devices can see all other peers in the network (both wired and wireless), but WIRELESS devices cannot see any other peers whatsoever (wired or wireless).
I have heard that this could be because of a faulty implementation of uPNP by Linksys, and in particular a problem with multicast filtering (and unfortunately the modem/router's firmware does not provide any relevant settings). But I am not sure.
I purchased this thing with the express purpose to use it on a Mac-only network, and I am thoroughly disappointed to see that it does not work, especially since UPNP is supposed to be supported.
I've got a problem with my new Linksys E1200 (v1) router. It cuts the bandwidth of my PPTP connection with ISP (which is 50 Mbps) down to about 12 Mpbs. My firmware is the latest one (v1.0.03 build 4). I've done some reading and found out that it's pretty common problem between Linksys E-Series routers and ISPs that use PPTP/L2TP.
View 4 Replies View Related