Linksys Cable / DSL :: WCG200 Wireless Is Not Working?

Jul 1, 2009

I have the WCG200 and it has been working fine with my Comcast service for the last 4 years with no issues, either wired or wireless.  Starting about a week ago, I have been having a lot of trouble with my wireless.   I am on Firmware Version: 2.0.3.9.31-1023 and my ISP is Comcast.  I have tried calling Comcast to see if there is a firmware update but that phone call usually doesn't go very far.

View 8 Replies


ADVERTISEMENT

Linksys Cable / DSL :: WCG200 Bridge Mode From Wireless-G Cable Gateway To Wired?

Mar 14, 2013

Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:

- WLAN AutoConfig service has successfully stopped.Wirel?

- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll

- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.

- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down.  Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]

Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.

View 9 Replies View Related

Linksys Cable / DSL :: How To Setup Password WCG200

Jan 31, 2008

How do I set up a password to secure my home wireless network. Gate is on a XP desktop. Just have my Vista notebook on network. Use WCG200 gateway which was given to me by relative who has upgraded.

View 6 Replies View Related

Linksys Cable / DSL :: WCG200 Power Plug Getting Very Hot?

May 26, 2007

I have a WCG200 v1, and lately it keeps reseting, so I started thinking maybe it's a power problem. I go to unplug it, and the power plug is extremely hot, so we unplug it, and let it cool off, then plug it back in later. It works fine, and we go to bed, I wake up this morning and it's back to very hot again..

View 2 Replies View Related

Linksys Cable / DSL :: WCG200 Factory Reset?

Apr 26, 2012

If I use the reset on the back of the WCG200 and reset it to the original factory settings, does the firmware version revert to the original version?

View 2 Replies View Related

Linksys Cable / DSL :: WCG200 Eventually Loose Connection

Jan 18, 2012

I'm having a problem with my WCG200 wireless gateway.  I can sucessfully use it to connect to the internet using the wireless feature but only for a short time (10-30min at a time). Eventually, I loose the connection.  I'm not sure if it's a modem issue or an ISP issue but only one of my two laptops has this trouble.
 
 Symptom: Connecting with a Dell Lattitude E5520 laptop It works normally until the "US" and "Online" LEDs turn off and only the DS light is left blinking. At that time I no longer have a connection to the internet.  Once I cycle power on the WCG200 it re-connects and works for a while, then the same issue repeats. I cleared the modem log and let the failure occur again to record the fresh log. 
 
 I attached the Modem Log in case that would troubleshoot. I've got the security of the modem set to allow the laptops MAC addresses and using WPA-personal / TKIP encryption. I never had this problem until I started using a new laptop,  I'm starting to suspect that my ISP is disconnecting that laptop for some reason ?

View 3 Replies View Related

Linksys Cable / DSL :: Installing Vista Drivers For WCG200?

Mar 25, 2007

WCG200?i have just bought a new laptop with Vista Home Premium as the OS.i've already downloaded the new driver file, and unzipped it. but how to i install it so that i can get online wirelessly?all my permissions are set properly to allow communication, but i cannot get onto the wireless network.i've also noticed that the WCG200 is not listed on the Linksys Windows Vista Support page. does this mean that my WCG200 is not supported to work with Vista. if so, why are there Vista drivers available for download?currently i am connected via wire and it works fine. it also detects my wireless network. the problem is just connecting to it.

View 9 Replies View Related

Linksys Cable / DSL :: No Drivers Were Listed As Needed For Wcg200

Jun 19, 2012

I just replaced a hard drive on my computer, installed win7, hooked up the linksys according to the guide but it is not recognizing anything attached.  My devices indicates an unknown ethernet controller.  I have installed no drivers for anything, no drivers were listed as needed for wcg200. 
 
The same linksys is hooked up to a second computer (which I am posting from) so I am assuming it works fine.  Also I had the thing set up on the last harddrive with win7, the only difference was the harddrive was loaded up with the OS by the computer shop.  I have never done this before and wanted to try it out. I swapped ethernet cables to make sure nothing changed with the cables, but no luck. 

View 1 Replies View Related

Linksys Cable / DSL :: BEFCMU10 Need To Install And Get Cable Modem Working

Mar 24, 2011

I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.

View 2 Replies View Related

Linksys Cable / DSL :: WAG320N Wireless Connectivity Stopped Working

Mar 29, 2011

I have had a WAG320N running problem free for approx 2 months, in that time I've upgraded the firmware 1.00.12 with no issues and has run fine for a month after upgrade. I have 3 laptops connected wirelessly and 2 pc's running wired (through homeplug system) plus TV, PS3 and ipods, all have run without issues.
 
All of a sudden 2 days ago all wireless connectivity stopped? SSID is still broadcasting and viewable but I can no longer connect with any computer or device. Wired connectivity is working fine.
 
I've checked security settings, turned off encryption, reset factory defaults, re-downloaded latest firmware and reflashed with no luck. As I said wirless stopped working all of a sudden with no changes to settings.

View 4 Replies View Related

Linksys Wireless Router :: WRT54GS With Mac OS 10.6.8 And RCN Cable Modem Not Working?

Sep 27, 2011

I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
 
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
 
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
 
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
 
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.

View 1 Replies View Related

Linksys Wireless Router :: Arris Cable Modem Not Working With WRT54G

Mar 7, 2007

I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.

View 9 Replies View Related

Linksys Cable / DSL :: X3000 Log Is Not Working?

Oct 1, 2012

Log enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use. 

View 1 Replies View Related

Linksys Cable / Dsl :: Wifi N Is Just Not Working On Wag320n

Mar 24, 2011

I just bought a macbook and want to connect with my WAG320N. I have no problem to connect on 54mbs what tells me that I'm on Wifi G. The settings in my router was on b/g/n so I changed it to just N but then it won't connect. I don't get error or nothing. I just doesn't connect. I tried all different kind of settings but no luck.

View 8 Replies View Related

Linksys Cable / DSL :: WAG120N Working With A Repeater?

Apr 5, 2013

what do i need to setup in WAG120N to work with a Wireless Network repeater?

View 1 Replies View Related

Linksys Cable / DSL :: WAG354G PPTP Vpn To M0n0wall Not Working

Jan 24, 2011

I have problems to make a PPTP vpn to my M0n0wall. PPTP passthrough is enabled, port 1723 TCP ist forwarded to M0n0walls WAN Interface. Rules on the M0n0wall are set correctly. It seems that the Linksys has problems with GRE 47 protocol routing. Does a newer model (WAG120N  or WAG320N)  work with PPTP passthrough?

View 5 Replies View Related

Linksys Cable / DSL :: Working With WAG320N Only As Modem ADSL?

May 7, 2012

i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?

View 1 Replies View Related

Linksys Cable / Dsl :: Wifi On Wag120n Stopped Working?

Mar 26, 2012

Like the title says, the wifi on my wag120n stopped working. It happened suddenly, nothing was changed in the settings. It stopped showing when i'm searching for wireless connections (SSID is still enabled).

View 3 Replies View Related

Linksys Cable / DSL :: WAG320n UDP Not Working On Port Forwarding?

Dec 5, 2011

I have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.

View 2 Replies View Related

Linksys Cable / DSL :: WAG320N Port Forwarding / DMZ Not Working

Mar 4, 2011

I'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
 
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
 
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.

View 1 Replies View Related

Linksys Cable / DSL :: WAG160Nv2 Not Working With New 2011 Macbook Pro?

Mar 20, 2011

Signal drops constantly and seems to be a problem with the Mac more than the router IMHO but i thought to register the problem here.
 
I'm not alone as many users on the Apple support forum are experiencing the same drops via airport and with different routers..  Lan line works fine for me with no issues
 
I will update the firmware and try that as it seems i am running old firmware V2.00.13

View 4 Replies View Related

Linksys Cable / DSL :: Home HG200 V2 Port Forwarding Not Working

Jul 20, 2011

I have got a Linksys @ Home HG200 V2 G Gateway. I am trying to setup port fowarding but its not working. I have gone onto the routers port forwarding setup page filled it out but the port is still closed.

View 4 Replies View Related

Linksys Cable / DSL :: X3000 Support Website Page Not Working?

Apr 11, 2013

Today i brought Linksys X3000 and that came with old firmware version (1.0.01). i need new version (1.0.03) Annex A firmware but support page not working.
 
Support Page is not working: [URL]

View 2 Replies View Related

Linksys Cable / DSL :: X2000 Settings Not Working For Century Link

Dec 22, 2011

I have a Linksys x2000 and have been using it successfully on DSL with a local ISP.  I recently changed to Century Link and now I can't connect to the internet (Century Link).  If I change the UserId and Password from my Century Link values back to my old ISP values, I can connect to my old ISP.  Century Link tells me they have my account active with the X2000 and Century Link.

View 2 Replies View Related

Linksys Cable / DSL :: WAG 200G - Installing Power Socket Not Working?

Mar 8, 2012

I purchased wag 200g from dubai more than a year ago. When i tried installing the power socket never worked and till date I never got a solution for this. At present I do not have any documents relafinding a cisco authorised service center in India but in vainted to this product but this issue could not be solved by any computer service center.

View 1 Replies View Related

Linksys Cable / DSL :: WAG120N Router Has Stopped Working Completely

Jun 26, 2012

My WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.

View 3 Replies View Related

Linksys Cable / DSL :: WAG54G2 - Bonjour Networking Stops Working After Few Minutes / Hours

Oct 21, 2010

Running Firmware v. 1.00.19 here, which I reckon is the most recent version.
 
My network consists of two Macbooks, an iMac and two iPhones. It utilizes WAP2 encryption and all devices are well within range, the environment being free of interferences from any other WiFi signals (this is a rural area). 
 
My problem: Bonjour networking stops working after a few minutes or hours. When the problem appears, WIRED devices can see all other peers in the network (both wired and wireless), but WIRELESS devices cannot see any other peers whatsoever (wired or wireless).
 
I have heard that this could be because of a faulty implementation of uPNP by Linksys, and in particular a problem with multicast filtering (and unfortunately the modem/router's firmware does not provide any relevant settings). But I am not sure.
 
I purchased this thing with the express purpose to use it on a Mac-only network, and I am thoroughly disappointed to see that it does not work, especially since UPNP is supposed to be supported.

View 1 Replies View Related

Use Wcg200 As Bridge?

Dec 19, 2012

So I have an RV120W as my "main router" but I can't get a wire into the garage to get a couple of computers in there access to the internet / LAN. I have a WCG200 cable gateway at my disposal, with a built in 4port switch and wondered if I can configure it's WLAN to connecto the RV120W SSID and use wireless as my link between my garage network and the rest of the house LAN? WCG200 isn't going to connect at blinding speeds, which I'm ok with, I just wanted to know if it's possible?

View 3 Replies View Related

WCG200 - VPN Not Connecting From Outside Of Router?

Jul 11, 2011

I am new to VPN and have set a server up using windows XP's built in feature. I have tried to connect to the VPN from inside the router and it works fine. but I can't access from outside of the router. The computer will connect but then when on the "Verifying Username and Password" step the connection will disconnect with error 721: The remote computer did not respond. The router that i have is a Lynksys WCG200, I have tried turning all the security features off. Could my router just not be compatible with VPN?

View 9 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N Router Stopped Working After Cable Pulled Out

Mar 14, 2013

Region : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home

I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?

View 4 Replies View Related

Dell :: Vostro 3450 Wireless Not Working - Internet Fine Via Ethernet Cable

Sep 7, 2011

Daughter is at college with brand new Vostro 3450.  Was working on school network during summer but drops the connection multiple times during the day.  She runs the Troubleshooting which then allows her to connect and 30 minutes later the connection is dropped again.  The laptop works fine when connected to the internet via the ethernet cable.  Here is what has been done by the IT support at the school.

1 -  Deleted the Intel wireless utility as they thought it was "fighting" with the Windows software for control over the wireless. 

2 - Increased the power for the wireless card to "high performance".

3 - Reinstalled Windows 7 to eliminate that there is a software issue.

4 - Replaced the Intel Wireless Card with new part sent by Dell.

Now the IT supports recommendation is to "get a new system" and that perhaps the Vostro's wireless card is "not compatible with their network".  For Dell computers they sell the Latitude to the students.

My daugther likes the Vostro.  She doesn't want to give it up.  Wants the system to work.  She had the laptop during the summer session and had problems with connection.  The Windows software was reinstalled thinking there was a virus (although no evidence of one) and then she had no connection problems for the whole summer.  She came home for 2 weeks and returned  back to school and then the system would not work again.

I don't know what to do.  Can I buy a USB wireless adapter for her to temporarily use until I can figure out how to fix this problem.  Personally, I think there is a design flaw with the vostro. 

View 3 Replies View Related

Ethernet Cable Not Working?

Jan 28, 2013

I have two ethernet cables, a long one and a short one. The short one works fine, but the long one does not work with my computer. It has worked with other laptops, so I am fairly sure the cable itself is fine - is there anything I can do

View 3 Replies View Related

Linksys Cable / DSL :: Atlanta 2100 - When Installing Driver To Use Usb Cable Modem Does Not Recognize It

Dec 13, 2012

I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved