I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
I recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it. My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?
View 1 Replies View RelatedI current have a Cisco 2100 Cable modem (192.168.100.1) connected to a Cisco Linksys E2000 (192.168.0.1) that is connected to a Cisco 3550 (192.168.0.10). I would like to relocate the E2000 to another room. This would require me to connect the 2100 and the E2000 through the 3550. I have had to set a MAC address clone on the E2000 of the PC that is also connected to the 3550.
The question I have is how do I get this all to interconnect so that the E2000 is used by the 2100 for validation to the internet provider (Time/Warner). I am also using the E2000 for DHCP.
Here is a copy of the running config:
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[Code].....
I wiped vista and installed windows Xp now my modem wont recognize and i dont have internet. i have tried burning the Drivers from Cisco onto another CD From another Machine but it says it needs internet connection to do so. i can't connect or anything i have a DPC2203 cable modem?
View 1 Replies View RelatedWith this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies View RelatedI inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View Relatedsome reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
I am having a LOT of trouble with an HP 6500A Plus wireless printer.It has been working wirelessly with my X2000 using WPA2 Personal encryption. (The WPA2 key has NOT been changed since it was working)It has recently stopped working and I cannot see why.All other devices (Wii, two iPads, 1 iPhone) all continue to work faultlesly.I have tried numerous times to reset the WPA2 security key on the HP Printer but each time it fails to connect to the X2000.It does recognize the SSID. But will not connect.I tried to turn on the LOG in the X2000 to see what information I could gather, but nothing get put into the Security Log. Maybe I am setting it up wrong, using "wireless" then "Log", then "enabled", then "view log", select "Security Log". attempt to connect from the HP Printer... twice, then refresh the log on the X2000, and NOTHING.
View 4 Replies View RelatedWCG200?i have just bought a new laptop with Vista Home Premium as the OS.i've already downloaded the new driver file, and unzipped it. but how to i install it so that i can get online wirelessly?all my permissions are set properly to allow communication, but i cannot get onto the wireless network.i've also noticed that the WCG200 is not listed on the Linksys Windows Vista Support page. does this mean that my WCG200 is not supported to work with Vista. if so, why are there Vista drivers available for download?currently i am connected via wire and it works fine. it also detects my wireless network. the problem is just connecting to it.
View 9 Replies View Relatedgetting ready to do the install of a EA4500 with a Cable internet provider. I found the site on Cisco on how to manually install the router with Cable [URL]It advises to first install using the software that comes with the router.It then gives the following steps:
Step 1:Access the router’s web-based setup page. For instructions, click here.NOTE: If you are using a Mac computer to access the router’s web-based setup page, click here.
Step 2:On the Setup tab, click the MAC Address Clone sub-tab.Step 2:Check the Internet IP Address. If it has numbers, this means the router has been properly configured.
NOTE: If the Internet IP Address values are showing up 0.0.0.0, click on Release IP Address then the Renew IP Address buttons.NOTE: For wireless-B and wireless-G routers, click on the DHCP Release and DHCP Renew buttons. MY QUESTION: are the steps above something that definately will need to be done or is that in the case that it's not configured via the installation using the software?I have this same router installed at my home however I use DSL internet and my daughter uses Cable internet so I want to make sure I am positive on the steps prior to installing.
I purchased wag 200g from dubai more than a year ago. When i tried installing the power socket never worked and till date I never got a solution for this. At present I do not have any documents relafinding a cisco authorised service center in India but in vainted to this product but this issue could not be solved by any computer service center.
View 1 Replies View Relatedwhere can I download this driver?
View 1 Replies View RelatedI've just upgrade my os to windows 7 and find a trouble searching for win7 driver for am300.
View 3 Replies View RelatedI just received a computer from a relative since they do not use it anymore. I just reformatted the hard drive and I can't seem to get it to connect to the internet. Every time I try my computer says there is no ethernet cable connected but I know it is. I read around on the forums and one thread (that is now closed), was about the same problem and to diagnose the problem they asked to use IPCONFIG/ALL in the cmd.exe. The results are this:
Windows IP Configuration
Host Name: bouss
Primary Dns Suffix:
Node Type: Broadcast
[Code]....
I'm using an nvidia ethernet card that's in my mobo. Yesterday I had internet without any problems but this morning when I turned my computer on, the light on it wasn't blinking. Tried turning power on/off, unplugging and pluhging back but still no solution.Checked Device Manager and there is no (!) or (?) next to the device name. Also it says device is working properly. Even did the "scan for hardware changes" and again it shows that device is working properly.. But that's not all! The weirdest thing here is that my 3 neighbours who are from the same ISP have the exact same problem. We're connectrd to 1 box that is outside. The other part of the village that is on the same ISP has no such problems. So I'm wondering if it's a local corrupt cable problem or our cards have fried. I believe we use fiber optic cables.
View 3 Replies View RelatedI have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies View RelatedHave an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.
View 1 Replies View RelatedI have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies View RelatedI have Linksys Befcmu10 v4. I need to port forward and I cannot login. I have tried admin/password and all those combinations. I tried factory restore by pressing the thing in the back and still can't access the page
View 6 Replies View RelatedI presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies View RelatedWCG200G ver.2 resets everytime i use wireless
Firmware Version: 2.0.3.6.12-0608
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies View RelatedI have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies View RelatedI recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies View Relatedi have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedIs there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies View RelatedI recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012
View 4 Replies View RelatedHow can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?
View 1 Replies View RelatedI currently have a WAG354G configured with a static IP address acting as a DHCP server. Wireless is off, and instead I have an Apple Airport Extreme basestation in bridge mode to which my client machines connect wirelessly.
Instead I want to pass through the static IP address to the Apple basestation, and use this as my DHCP server.
Ultimately I want the Apple basestation to pass the static IP address through to my home server, and also supply DHCP addresses to other clients.
Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
