Linksys Cable / DSL :: WAG35G To Act As Modem Passing Through A Static IP?
Feb 27, 2011
I currently have a WAG354G configured with a static IP address acting as a DHCP server. Wireless is off, and instead I have an Apple Airport Extreme basestation in bridge mode to which my client machines connect wirelessly.
Instead I want to pass through the static IP address to the Apple basestation, and use this as my DHCP server.
Ultimately I want the Apple basestation to pass the static IP address through to my home server, and also supply DHCP addresses to other clients.
View 5 Replies
ADVERTISEMENT
Sep 23, 2011
I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
View 1 Replies
View Related
Jul 26, 2011
I've been having a problem with setting up static dns 3 on my WAG, what has been set is...
Static DNS 1: 208.67.222.222
Static DNS 2: 208.67.220.220
Static DNS 3: 208.67.220.222
Now if I look in my router status screen 1&2 are correctly displayed but the 3rd entry is showing my ISP's DNS,
View 9 Replies
View Related
Dec 13, 2012
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
View Related
Apr 23, 2013
With this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies
View Related
Mar 24, 2011
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Jun 4, 2010
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
View 8 Replies
View Related
Dec 1, 2012
Just picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?
View 5 Replies
View Related
Jan 24, 2011
I am having trouble finding a way to set a static IP on the WAG320N Gigabit.
View 1 Replies
View Related
Jan 2, 2013
I have a WAG 120N Modem Router, My question is: Can you assign an static IP to a pc using this router?
View 2 Replies
View Related
Aug 3, 2011
I currently have service with AT&T DSL. I have their Motorola Netopia 3347 modem that is set to Bridged mode and going to a Linksys WRT54GL router, which then goes out to a Cisco 24 port switch.AT&T has given us a Static IP to use, which was set up and working just fine when the modem was NOT in Bridged mode. Now that I have it set to bridge mode (as per a request by our VoIP provider), our IP address is no longer static at WhatismyIP.com...instead it changes frequently. However, I have a back up server here that needs to have a static IP so offsite back ups can find our modem/router and then the back up server.I am running Tomato software on the Linksys admin. When I go to the Basic->Network section, the WAN/Internet is set to PPPoE with the AT&T username and password that was originally used in the Netopia modem entered in. If I set this option to Static, it removes the username/password fields, so I do not think that my internet would work that way. Or, would the Netopia use the username/password to authenticate, and then just pass it through to the Linksys in bridge mode and THEN it would use the static IP? what I need to do to make the Linksys grab our Static IP instead of changing? Neither AT&T or the VoIP company can figure it out...
View 2 Replies
View Related
Jun 9, 2012
I have a wireless printer set up with a static IP from below the DHCP restricted range but whenever the printer goes into powersave when awakening I lose connection and ping shows the static IP address being translated to one already allocated in the DHCP range. I can get around this by rebooting the router but its a pain to do this everytime we need to print.
192.168.1.52 is this Laptop
SungStar:/home/john # ifconfig wlan0wlan0 Link encap:Ethernet HWaddr 00:1F:3C:1C:E3:2F inet addr:192.168.1.52 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21f:3cff:fe1c:e32f/64 Scope:Linkjohn@SungStar:~> ping -c 5 192.168.1.10PING 192.168.1.10 (192.168.1.10) 56(84) bytes of data.From 192.168.1.52 icmp_seq=2 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=3 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=4 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=5 Destination Host Unreachable
View 8 Replies
View Related
Apr 3, 2011
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
View 1 Replies
View Related
Jul 2, 2012
The router I am using is the Linksys X2000 wireless-N ROuter with ADSL2+ Modem. How to give my linux server a static Ip adress. I've googled it and I don't understand how they are telling me to set it up in the router.
View 3 Replies
View Related
Apr 18, 2013
I am trying to determine why Comcast Business Class modem configured with a static IP (IPV4) works with a laptop or Linksys Cable modem but not with a Cisco ASA 5505. After a few minutes, the 5505 stop passing web traffic. I am able to ping the default gateway even though I can not surf the web. Restarting the 5505 and the Comcast modem, web traffic flows for a short period of time, then stops. I can connect inside the firewall via ASDM 7.1.1 and via SSH. I can not connect via either from the outside. Comcast tech support indicated their router is working and is configured in bridge mode. I swapped out the 5505's memory, and then with another 5505. Nothing seems to resolve the issue. I am trying to determine if the 5505 or the Comcast router is not configured correctly.
Here are the parameters: The 5505 was reset to default factory settings via the command: config factory-default. Configured the outside interface with static IP Address followed by the no shutdown command, then removed DHCP features from outside interface. Added Comcast DNS servers, default route, ntp servers, configured DHCP features on the inside interface. Enabled HTTP/SSH (inside & outside interfaces) and ICMP echo-reply (outside only).
I believe the Comcast modem is not configured correctly. The show version and show startup output are below.
ciscoasa# show version
Cisco Adaptive Security Appliance Software Version 9.1(1)
Device Manager Version 7.1(2)
[Code].....
View 5 Replies
View Related
Jul 17, 2011
I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies
View Related
Oct 2, 2011
Have an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.
View 1 Replies
View Related
Apr 18, 2013
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies
View Related
Jul 7, 2008
I have Linksys Befcmu10 v4. I need to port forward and I cannot login. I have tried admin/password and all those combinations. I tried factory restore by pressing the thing in the back and still can't access the page
View 6 Replies
View Related
Apr 22, 2013
I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
View 1 Replies
View Related
Nov 27, 2011
I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies
View Related
Apr 27, 2012
WCG200G ver.2 resets everytime i use wireless
Firmware Version: 2.0.3.6.12-0608
View 8 Replies
View Related
Jun 25, 2012
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies
View Related
Apr 15, 2013
I have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
View 1 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
Jul 8, 2012
I recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies
View Related
May 7, 2012
i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies
View Related
Mar 23, 2011
Is there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies
View Related
Mar 13, 2013
I recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012
View 4 Replies
View Related
Nov 7, 2011
How can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?
View 1 Replies
View Related
Mar 27, 2012
I recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it. My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?
View 1 Replies
View Related
Jan 11, 2013
how to i connect mu linksys router to my ubee cable modem
View 2 Replies
View Related
