Linksys Cable / DSL :: Cisco Modem DPC3825 Won't Recognize It
Mar 27, 2012
I recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it. My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?
View 1 Replies
ADVERTISEMENT
Apr 23, 2013
With this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies
View Related
May 24, 2011
I am looking to permanently reset the default remote management port of the MODEM DPC3825 to something other than 8080. how to PERMANENTLY change the port from 8080? In the web interface under administration I have several times set it to something else other than the defaulted 8080 but when the modem is rebooted or reset, it goes back to the default 8080.
View 4 Replies
View Related
Sep 20, 2012
i have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in
View 1 Replies
View Related
Dec 13, 2012
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
View Related
Aug 26, 2011
I got a new modem today (a Cisco DPC3825) and it seems to be presenting a problem. I used to be able to simply and quickly change my IP address, by changing the MAC address though my Netgear router. Now when I do that, I can see the IP address has changed in the router settings, but when I double check it using ipburger.com, the IP address does NOT actually change, but remains the same.
View 4 Replies
View Related
Aug 19, 2011
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies
View Related
Feb 25, 2012
I am having a LOT of trouble with an HP 6500A Plus wireless printer.It has been working wirelessly with my X2000 using WPA2 Personal encryption. (The WPA2 key has NOT been changed since it was working)It has recently stopped working and I cannot see why.All other devices (Wii, two iPads, 1 iPhone) all continue to work faultlesly.I have tried numerous times to reset the WPA2 security key on the HP Printer but each time it fails to connect to the X2000.It does recognize the SSID. But will not connect.I tried to turn on the LOG in the X2000 to see what information I could gather, but nothing get put into the Security Log. Maybe I am setting it up wrong, using "wireless" then "Log", then "enabled", then "view log", select "Security Log". attempt to connect from the HP Printer... twice, then refresh the log on the X2000, and NOTHING.
View 4 Replies
View Related
Oct 5, 2012
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
View 9 Replies
View Related
Mar 24, 2011
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Jun 4, 2010
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
View 8 Replies
View Related
Nov 4, 2011
I have a DPC3825 from Shaw Cable in Canada. I'd like to use my Airport Extreme as a repeater using WDS. I've clicked the checkbox for "Allow wireless signal to be repeated by a repeater" and entered my Airport's MAC Address, but my Airport Base station doesn't see it as a WDS Peer.
View 1 Replies
View Related
Apr 29, 2013
Just got a Cisco DPC3825 from my ISP. I need to connect my other desktops to the wireless router all over the house and have two questions.
1. What is the best wireless adapter to use so my other desktops will be able to access the router?
2. What is the distance of signal before I need a signal booster and if I do need to boos the signal, what is the best device to do that? (we stream video, music, light gaming and general internet applications).
View 2 Replies
View Related
Jan 6, 2013
I am trying to figure out whyt my DPC3825 does not maintain a FTP session I did not really want to post this message rather I am trying to figure out how to search this board.
View 1 Replies
View Related
Nov 13, 2010
NIB DPC3825 cable modem. Called my provider and got it provisioned and its working (I'm on an ethernet connection posting this). But when I http to 192.168.0.1, I get a screen that doesn't quite look like the one in the manual. I enter the "admin" and "W2402" and click login, and the screen refreshes but nothing happens (no configuration options, only able to check status of downstream and upstream channels). Pushing the factory reset button for ten seconds to load defaults makes the lights blink and then reboots; same result as above. Pushing the wireless config button has no effect at all.
View 3 Replies
View Related
Jan 9, 2013
I got a problem with my router CISCO (DPC3825) where the eithernet is working properly and the wireless is not, and I had to plug the usb to make the setups, and suddenly the wireless was working but when I tried to reset the password something worng happened change the set of the wireles
View 2 Replies
View Related
Jul 30, 2011
I just received a computer from a relative since they do not use it anymore. I just reformatted the hard drive and I can't seem to get it to connect to the internet. Every time I try my computer says there is no ethernet cable connected but I know it is. I read around on the forums and one thread (that is now closed), was about the same problem and to diagnose the problem they asked to use IPCONFIG/ALL in the cmd.exe. The results are this:
Windows IP Configuration
Host Name: bouss
Primary Dns Suffix:
Node Type: Broadcast
[Code]....
View 5 Replies
View Related
May 21, 2012
I'm using an nvidia ethernet card that's in my mobo. Yesterday I had internet without any problems but this morning when I turned my computer on, the light on it wasn't blinking. Tried turning power on/off, unplugging and pluhging back but still no solution.Checked Device Manager and there is no (!) or (?) next to the device name. Also it says device is working properly. Even did the "scan for hardware changes" and again it shows that device is working properly.. But that's not all! The weirdest thing here is that my 3 neighbours who are from the same ISP have the exact same problem. We're connectrd to 1 box that is outside. The other part of the village that is on the same ISP has no such problems. So I'm wondering if it's a local corrupt cable problem or our cards have fried. I believe we use fiber optic cables.
View 3 Replies
View Related
Oct 11, 2012
Region : Belgium
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : 3G mobile
My router TL-MR3420 does not connect to my 3G modem. I did all the steps according to the router configuration. Despite of that, once it is on the status it doesn�t recognize my modem, HUAWEI, model number E1820.
View 5 Replies
View Related
Jan 15, 2012
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies
View Related
Dec 17, 2012
Recently installed a new CISCO DPC3825 and set up for wireless. I can connect to the network, signal strength excellent, but NO Internet. i have read a few threads showing similar issues, but i am getting lost when i try to troubleshoot further. i ran a command 'ipconfig/all' and got some data. I am confused also as under my network adapter it says 'media disconnected' .
View 1 Replies
View Related
Jul 17, 2011
I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies
View Related
Feb 6, 2011
When setting up Belkin fF5D8235-4 v2 router it will not recognize the Speedstream 4100 modem. Is there a fix for this?
View 1 Replies
View Related
May 31, 2011
When installing the DIR-615, router installs, but error msg that there is no internet connection. SmartConnect is plugged into the WAN and I have tried the ethernet cable to the computer in spots 1 & 2. Good connection when SmartConnect modem is connected to computer directly.615's Internet indicator will turn green for a while, usually less than a minute or two, then flashes, then may actually cause the routers status indicator to flash off, then back on. Like a reset.
View 2 Replies
View Related
May 10, 2013
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
View 6 Replies
View Related
Oct 2, 2011
Have an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.
View 1 Replies
View Related
Apr 18, 2013
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies
View Related
Jul 7, 2008
I have Linksys Befcmu10 v4. I need to port forward and I cannot login. I have tried admin/password and all those combinations. I tried factory restore by pressing the thing in the back and still can't access the page
View 6 Replies
View Related
Apr 22, 2013
I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
View 1 Replies
View Related
Nov 27, 2011
I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies
View Related
Mar 14, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
View 5 Replies
View Related
Feb 1, 2012
I have CISCO DPC3825 router and theres about 3 computers and 2 wireless devices using internet through it. When i connect to a online video game I get these mini-disconnects. It happens periodically and frequently I'm not sure what is causing it.
View 1 Replies
View Related
