PS3 Doesn't Recognize Connection When Connected Directly To Modem
Jan 15, 2012
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies
ADVERTISEMENT
Jun 9, 2011
I have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again. I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do. When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
View 12 Replies
View Related
Oct 5, 2012
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
View 9 Replies
View Related
May 10, 2013
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
View 6 Replies
View Related
Dec 12, 2011
I recently had to reinstall XP and all the drivers for my friend's laptop but it seems it does not recognize any wireless connections. When I click the Choose a wireless network it says "No wireless networks were found in range" however I can use my laptop just fine.I clicked the network adapter and it says everything is running fine so I am not sure what the issue is. How to get the wireless internet working.
View 2 Replies
View Related
Jun 12, 2012
I just moved into a new apartment and inherited a former roommates internet set up. Our router was infected with DNSchanger, so I sought to reset the router and update the firmware. I reset the router and it no longer recognized the internet connection. I can connect when plugged directly into the modem, but the router doesn't recognize the internet connection. Below is my ipconfig/all log:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersREDACTED>ipconfig/all
[Code].....
View 4 Replies
View Related
Oct 20, 2012
I have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.
View 1 Replies
View Related
Mar 8, 2013
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies
View Related
May 31, 2011
When installing the DIR-615, router installs, but error msg that there is no internet connection. SmartConnect is plugged into the WAN and I have tried the ethernet cable to the computer in spots 1 & 2. Good connection when SmartConnect modem is connected to computer directly.615's Internet indicator will turn green for a while, usually less than a minute or two, then flashes, then may actually cause the routers status indicator to flash off, then back on. Like a reset.
View 2 Replies
View Related
Nov 22, 2012
From last two days, my internet disconnecting frequently. Modem catching correct ip but no internet connection.modem catches correct ip address n other things, it shows connected to home network (i.e hathway) and internet access is allowed but browser display error 'webpage is not available' (same result for login page of ISP). I have tried different browsers but same result. windows network diagnosis center results as "your computer appears to be correctly configured, but the device or resource is not responding " OR "login.hathway.com is online but still not responding after couple of tries"(second error is not correct word to word tht was the over all meaning of it)In ping test, ping to default gateway gives very good result as 5-20ms but 'request time out' for url...So am not understanding whether it is my pc's problem or from ISP.I m using single pc with wired modem. windows 7 no changes made in network n sharing center.
View 2 Replies
View Related
Jan 1, 2012
I have an IBM R-40 thinkpad that I restored to original with the IBM icon and then updated it to a service pack 3 and updated anything that popped up. Now it doesn't recognize any wireless at all. I tried the FN,F5 still no luck. It has a INTEL card, Model WM3B2100 in it and it worked fine before the restore and update.
View 1 Replies
View Related
Apr 9, 2012
I am trying to an Epson WF 545 to connect to a wireless network. I get an error message when it fails to connect to a networked iMac. The message says, "Entered security key/password does not match the one set for your router/access point."Several weeks ago, I had to reset my wireless network password/security key. That reset worked for our 3 PCs and 2 Macs including this iMac...the one that now doesn't connect to the wireless printer or maybe vice versa...why the iMac can't connect to the Epson (or vice versa), but the iMac does connect to the wireless network, and in order to do that, it makes use of the new network password / security key that I just put in the Epson to set it up in the network. Can you tell me if the wireless router somehow has a password / security key that I did not change when I changed the wireless network security key? The new network password/security key that I entered in the Epson is correct.
View 9 Replies
View Related
Aug 30, 2011
when I click on an icon like yahoo or facebook or any other icons my compuyrt says doesnt recognize,typed in add wrong, cant figute it out. Its on dsl an my laptops work fine from my wireless.
View 2 Replies
View Related
Jan 31, 2013
I just set up my wireless security, and I get "incorrect password" message when I try to log onto my ipad.
View 1 Replies
View Related
Jan 1, 2012
My gateway net book has always recognized wifi, but since we left home a few weeks ago I have not been able to connect. My computer savvy nephew couldn't even figure it out.
View 1 Replies
View Related
May 21, 2012
I'm using an nvidia ethernet card that's in my mobo. Yesterday I had internet without any problems but this morning when I turned my computer on, the light on it wasn't blinking. Tried turning power on/off, unplugging and pluhging back but still no solution.Checked Device Manager and there is no (!) or (?) next to the device name. Also it says device is working properly. Even did the "scan for hardware changes" and again it shows that device is working properly.. But that's not all! The weirdest thing here is that my 3 neighbours who are from the same ISP have the exact same problem. We're connectrd to 1 box that is outside. The other part of the village that is on the same ISP has no such problems. So I'm wondering if it's a local corrupt cable problem or our cards have fried. I believe we use fiber optic cables.
View 3 Replies
View Related
Sep 11, 2012
I'm using sapo internet USB pay as you go internet,the only problem I cannot get my windows vista to get connected . the software downloaded perfectly it just cannot connect to network! the computer i'm using now is gonna disappear soon!
View 1 Replies
View Related
Aug 18, 2012
My computer does not see the internet. If I do a restore to an earlier restore point, it can see the internet,, but when I do a restart it goes back to not allowing me to access it. The weather gadget cannot see the internet either. The OS is Win7 64.
View 1 Replies
View Related
Feb 29, 2012
Why isn't it possible to make following configuration:
View 9 Replies
View Related
Jan 16, 2012
if you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies
View Related
Mar 27, 2012
Can an ip address be NAT'ed to an ip address on a PIX 515 which isn't an ip address of a network directly connected to an interface on the PIX?
Specifically, can a host with an ip address of 150.140.102.3/26 which is connected to a network whose PIX firewall interface is 150.140.102.1/26 be NAT'ed to an ip address of 150.90.70.1/24 which is not a ip address of an interface that is directly connected to that same PIX 515?
I've attached a PDF depicting the network topology and describing the above.My first response to this question is that it can't be configured to do this, but need either a confirmation or correction to this.
View 2 Replies
View Related
Jul 23, 2011
My computer suddenly doesnt recognize my router.it recognizes othrer routers, and my other PC's are recognizing the router.the router is located very close to the PC, and no other electronic devices located near by.
View 2 Replies
View Related
Mar 18, 2013
My Dell destop with Windows 7 all of a sudden doesn't seem to recognize my router, yet my laptop works fine (which I'm using now). After reading other posts, I reset the router with no results, used a new cable from the Belkin to the computer, changed ports, checked connections, restarted; nothing. When I do an ipconfig, a small window pops open and goes off before I can make anything out. I undestand Belkin's IP address is 192.168.2.1 and I'm showing that my IPv4DHCP Server is that, as is my DNS server. The IPv4WINS server shows nothing.
View 9 Replies
View Related
Jan 22, 2013
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
View 1 Replies
View Related
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
View Related
Aug 22, 2012
I wanted to connect to the internet so plugged the same cable into my laptop (running 7) [code]...
View 3 Replies
View Related
Nov 29, 2012
I think our brand new Belkin router toasted itself after it automatically updated it's firmware. We've had it for three days the first two days we were downloading around 2MB/s, then last night it updated itself and since then it's been crawling around 100kb/s.
I've tried to plug the desktop right into the modem to see if it'd speed back up but it won't give it internet access this way. I've tried rebooting the modem after and before switching cables around but nothing will make it change.
View 5 Replies
View Related
Jan 14, 2013
i'm using WLC AIRCT5508-K9 software version 7.3.101.0, ISE, cisco prime infrastructure 1.2 (1.2.1.012), and using Odyssey access client manager all running well but here the problem, when a user connected to our SSID, the status of connection information especially on access point.. there appear that "Access point : WLC2-ISC-JKT-GCC".that is the WLC not the access point, is there any miss configuration from me..
View 5 Replies
View Related
Nov 11, 2012
I've been trying to find a response or a fix to this issue for a few weeks now.My DIR-655 RevB router is currently at firmware 2.07NA, and has speeds of around 30Mbps down and 10Mbps up when connected directly through wired connections.However over wifi, I am only getting around about 5 Mbps down and 2 Mbps up. I've tried the 'usual' fixes suggested on here, change broadcast signal to manual, not auto, shutting of QoS shaping, all of that. However nothing seems to be improving the speed.
View 8 Replies
View Related
Mar 28, 2013
I'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).
View 2 Replies
View Related
Nov 3, 2012
We had a problem where a 4500 would not ping directly connected devices dispite being able to telnet to them and also view them in CDP. It was mostly forwarding packets between devices but some hosts could not connect to others.
View 1 Replies
View Related
Oct 16, 2011
just got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
View 5 Replies
View Related
Apr 1, 2012
I just installed two of the HWIC-1GE-SFP cards in the CISCO3945 router but they are not recognized... I don't see any messages on the console output. I don't see them in the "show diag" command. I don't see new ports in the "show run" either... Is there some command I need to put in to activate them? Here is show version of my router:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
View 1 Replies
View Related