Cisco Wireless :: AIRCT5508-K9 Client Seems Directly Connected To WLC
Jan 14, 2013
i'm using WLC AIRCT5508-K9 software version 7.3.101.0, ISE, cisco prime infrastructure 1.2 (1.2.1.012), and using Odyssey access client manager all running well but here the problem, when a user connected to our SSID, the status of connection information especially on access point.. there appear that "Access point : WLC2-ISC-JKT-GCC".that is the WLC not the access point, is there any miss configuration from me..
View 5 Replies
ADVERTISEMENT
Jul 17, 2012
access points are directly connected to 2016 wlc.Event log from the wlc
AP event log download completed.
======================= AP Event log Contents =====================
*Mar 1 00:00:30.157: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:30.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:30.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:30.191: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
[code]....
but still access points are not functional ?
View 17 Replies
View Related
Feb 29, 2012
Why isn't it possible to make following configuration:
View 9 Replies
View Related
Mar 27, 2012
Can an ip address be NAT'ed to an ip address on a PIX 515 which isn't an ip address of a network directly connected to an interface on the PIX?
Specifically, can a host with an ip address of 150.140.102.3/26 which is connected to a network whose PIX firewall interface is 150.140.102.1/26 be NAT'ed to an ip address of 150.90.70.1/24 which is not a ip address of an interface that is directly connected to that same PIX 515?
I've attached a PDF depicting the network topology and describing the above.My first response to this question is that it can't be configured to do this, but need either a confirmation or correction to this.
View 2 Replies
View Related
Mar 28, 2013
I'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).
View 2 Replies
View Related
Nov 3, 2012
We had a problem where a 4500 would not ping directly connected devices dispite being able to telnet to them and also view them in CDP. It was mostly forwarding packets between devices but some hosts could not connect to others.
View 1 Replies
View Related
Jan 16, 2012
if you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies
View Related
Apr 11, 2013
I am trying to test (if possible) the idea of having 2 6509-E switches connected directly to each other while using VRF-lite (Sup 2T). The idea is to have 3-4 separate networks. For example Net-A, Net-B,Net-C, Net-D. There is no PE router*, just these two switches. Also, there sin't any other access layer switches. All users connect directly to the 6509-E's via switch 48 port switch blades.
Net-A and Net-B on separate VRF's, but able to talk to each other. Net-C and Net-D* on separate VRF's without being able to talk to any other. Net-D* will have a PE since it comes from an external network. This is something I would like to test in a lab environment, but I am not familiar with VRF's.
View 1 Replies
View Related
Jan 15, 2012
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies
View Related
Nov 11, 2012
I've been trying to find a response or a fix to this issue for a few weeks now.My DIR-655 RevB router is currently at firmware 2.07NA, and has speeds of around 30Mbps down and 10Mbps up when connected directly through wired connections.However over wifi, I am only getting around about 5 Mbps down and 2 Mbps up. I've tried the 'usual' fixes suggested on here, change broadcast signal to manual, not auto, shutting of QoS shaping, all of that. However nothing seems to be improving the speed.
View 8 Replies
View Related
Dec 1, 2011
I have a CAT 3560 connected to a ISR 2911 The 3560 has 2 subnets ( 192.168.1.0 /24 and 10.10.10.0 /24) The 2911 has interface GigabitEthernet0/1 on the 192.168.1.0 /24 and another GigabitEthernet0/0 on a WAN connection 172.16.7.246 I need to NAT both the 192.168.1.0 /24 and the 10.10.10.0 /24 to the single address 172.16.7.246 I have to use route-maps . I have IPSec VPN's and ZBF on the 2911 My problem is the NAT does not work for the 10.10.10.0 /24 network!Why?is my only option to use trunking between the 3560 and 2911 and subinterfaces on the 2911? I want to avoid sub-interfacing.
=============================================================
On the Cat 3560=====================!vlan 40name the 192.168.1.0 /24 subnet!vlan 60name the 10.10.10.0 /24 subnet!interface FastEthernet0/7description Connection to Router Gig0/1switchport access vlan 40!interface FastEthernet0/16description Connection pc host on the 10.10.10.0 /24 subnetswitchport access vlan 60!interface Vlan1no ip address!interface Vlan40ip address 192.168.1.4 255.255.255.0!interface Vlan60ip address 10.10.10.10 255.255.255.0!ip classlessip route 0.0.0.0 0.0.0.0 192.168.1.1
=========================
The host on the 10.10.10.0 /24 network has the 10.10.10.10 address as it's default gateway The host can not access the WAN thru NAT....
View 3 Replies
View Related
Jan 9, 2012
My Data Center has one single core switch where is connected several servers, one port is the link to the router wan and other port is the link to the FW, my boss wants to install 2 nexus in order to replace the single switch. All my network has only one address, for example 192.168.10.0/24 if I connect two nexus 7010 in VPC and Domain, each nexus is going to has 2 modules with 48 port 10/100/1000 rj45 and i wan to connect servers directly to each nexus, with this figure i'm going to have a group of servers connected in two different nexus, Do they can have the same network 192.168.10.0/24 considering that the nexus are in the same vdc and vlan and have only one gateway for both groups? If the answer is positive, which nexus would be the gate way for that address, the primary or secondary? Or i must have a different address for both group of servers, i mean for example 192.168.10.0/24 and 192.168.12.0/24?thus each nexus would be the gateway for that new address?
To have two nexus connected by VPC in a Domain mean that one computer connected to one nexus can share the same address or vlan with other computer connected to the other nexus????
View 2 Replies
View Related
Sep 9, 2012
We have a 3750X VTP Server and the rest of the switches are clients.
Due to cabling issues, we have a switch (Switch F) that we can't connect directly to the 3750X so we have it connected through another switch. Everything is set to VTP client with the correct domain and password but this not-directly-connected switch isn't receiving any VTP VLANs.
Anything I need to do on Switch D so that Switch F can receive the VTP updates?
View 3 Replies
View Related
Oct 27, 2011
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
View 1 Replies
View Related
Jun 9, 2011
I have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again. I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do. When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
View 12 Replies
View Related
Jun 27, 2010
A specific switch port which happens to be part of a 2 switch 3750 Switch Stack is seeing multiple CDP packets from 3 extra switch port interfaces that are not directly connected. Noteworthy is that the far end devices have the correct CDP entries and I physically confirmed at least two of those connections that lead to the switch "upstream to the culprit switch". Tricky part is that its production so room for maneuvering is limited. At some point I disabled all Ports save for the real uplink and the problem momentarily disappeared. Re-enable the interfaces problem resurfaces. Is there an explanation, technique to eliminate the culprit with minimal disruption?
View 4 Replies
View Related
Jul 18, 2012
I have a Cisco 7206VXR running 12.4(24)T3 IOS. It is configured with WCCPv2 using L2 mask redirection. I am using service groups and associated extended ACLs to select which subnets I want to redirect port 80 traffic from.
It is working fine for the subnet 192.168.1.0/24....
int gi0/2
ip wccp 10 redirect in
ip address 192.168.1.99 255.255.255.0
... however, there is OSPF running between the router and a Mikrotik device directly connected to this interface. The gateway addresses for all the client subnets are on the Mikrotik. Traffic from other subnets, e.g. 192.168.2.0/24, 192.168.3.0/24 come in on this interface and I want to redirect those too. But it appears that the redirection doesn't work for those subnets (I don't see any hits on the relevant ACL for any subnet except 192.168.1.0/24).
It seems like the router only wants to redirect traffic for subnets that it has an IP address in itself. Admittedly, all of the example configs i've found on cisco.com are for redirecting traffic from directly connected subnets but I can't find anything that denies thie possibility of redirecting any traffic that comes in on a given interface.
The question is, is this how WCCPv2 redirection works? i.e., the router must have an IP address in the subnet to be redirected?
View 1 Replies
View Related
Aug 15, 2012
we have the following setup for our network :
UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941s
Since last week we started noticing this problem that the branch users started to complain of slow application response.. After verifying it with the ISP and middle network we noticed that if i ping from my machine (ie usernetwork) to the WAN Router interface (facing the ASA) , i get time outs.. which is strange cause this is directly connected to it via ethernet cable.
View 5 Replies
View Related
Oct 24, 2011
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies
View Related
Apr 14, 2013
I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
View 5 Replies
View Related
Jun 26, 2012
Background: Wireless credit card machines can't stay connected to the 5508 controller 7.0.116 / 1142 ap wireless system. MAC address of one of the wireless hosts is 00:12:0e:ec:ce:97. AP servicing them is d4:a0:2a:99:34:60. Hosts are able to connect to the network after a reboot and stay connected for random periods of time but then don't come back unless you manually reload them. I have 3 in total in the same room services by the same ap.
I have the output of debug client 00:12:0e:ec:ce:97. Output showed 802.1x 'timeoutEvt' Timer expired for station 00:12:0e:ec:ce:97 so I increased the value to 4000ms on the controller but am still having the issue.
Note that the output below is the state the client stays in after receiving the timeout (802.1x 'timeoutEvt') showing subsequent attampts. The only way to get them back on is a reload of the credit card machine.
[Code]........
View 3 Replies
View Related
Jun 24, 2011
I've got a setup like this:
WLC 5508 v7.0.98
6-7 Autonomous upgraded to lightweight APs - 2 * 1231G while the rest are 1242AG
3 dynamic interfaces, 2 to Corp (diff VLANs) and 1 to Guest
4 WLANs binded to different interfaces
2 to the Corp interface Vlan X
1 to Guest
1 to Corp Vlan Y
DHCP for Corp is provided by their own Win DHCP server while controller is the DHCP server for Guest. Lease time is 1 day.
My problem now is, some clients, at random, loses their IP after being connected to the network. They get a 169.254.x.x. They connect to the Corp network OK, no browsing issues but after a while, they lose their IP address.
They can either wait for a while before getting an IP back or just simple renew their IP on their machine.
I've tried increasing the threshold values in the Local EAP to double its default values and also setting the WLAN session time out values to infinite. However, these 2 didn't work. I'm still having clients that occasionally lose their IPs at random.
I've also noted that this affects clients with WZC wireless drivers and not others e.g. Intel Proset.
View 7 Replies
View Related
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Apr 21, 2013
CISCO ASA 5520 -K9 .Client can connects ASA server and get ip address(172.168.31.X),but can't ping ASA inside interface ip address and other servers in lan .
View 2 Replies
View Related
Jul 5, 2011
I have a site to site vpn set up. I want to be able to manage the Cisco ASA router from a computer that connects to this site to site vpn. The problem is when I enter the ip address of the asa into adsm I get this error: Unable to launch device manager from 192.168.14.1:444. I am also unable to ping 192.168.14.1 from any computer that connects to the VPN, but I can ping other devices on the 192.168.14.x network. Also devices on the 192.168.14.x network can access the asa no problems. Here is my config:
ASA Version 8.2(1)
!
hostname Hostname
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
View 1 Replies
View Related
Jan 18, 2013
I am trying to connect my 2800 Series CIsco Office router with VPN client software from home. I can successfully authenticate and get the IP address from the pool configured but couldnt ping any LAN Ips including default gateway. I am pasting my router's configuration.
IP Address Of LAN: 192.168.22.x/ 24
IP Addresses handed out to Clients: 10.10.10.5- 10.10.10.20
aaa new-model
!
!
aaa authentication login default local
[code]....
I have noticed that my virtual-access interface comes up but the line protocol of virtual-interface remains down as follows:
Virtual-Template100 x.x.x.x YES TFTP up down
Also The client PC picks up a random gateway of 10.10.10.1 which I never configured anywhere on the server.
View 26 Replies
View Related
Jun 3, 2013
I have two ASA5505 with a site to site VPN.One of the ASA is connected to the internal network 192.168.150.0.The other one is connected to 192.168.151.0.
I have also configured IPSec Cisco client VPN to the one which is plugged to 192.168.150.0.
I would like to know if it is possible for a client connected with the Cisco VPN to access the network 192.168.151.0 through the site to site VPN.
View 3 Replies
View Related
Apr 18, 2012
Our client has MPLS connected all sites. Each site has a router connected to MPLS via serial interface, and connected to the switch (6500) via ethernet interface. There is QoS applied on the serial interface for outbound.
It appears there are lots of inbound traffic coming to the site, and the client applied QoS on outbound.What I learned that after the packet are marked by the CPE, the ingree Provider Edge Router (PER)uses these marking to map flows to various Label Switched Paths (LSPs) providing differentiated treatment accross the network. Then at egree, the PER applies queuing policying based on the CPEs orginal DSCP markings to properly allocate bandwidth on the egrees link during congestion. My guess we really don't need to have inbound policy applied in the serial interface on the router, am I correct?
The serial interface has 1.5 MB, and the goal is we want to have 1 MB for cirtical apps, and 0.5 MB for download/upload internet access. If we apply this policy on the switch, A) should I apply it on the VLAN interface or the port connected to the router?
View 6 Replies
View Related
Jul 2, 2011
I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc.
View 3 Replies
View Related
Sep 24, 2012
I've installed Fortigate 60B and now need to provide access to our guests. Guests must be isolated from office infrastructure. For this configuration I've set up DMZ interface with DHCP server. Client connected to DMZ port gets DHCP configuration but can't go out to the Internet.
Internal interface:
Addressing mode: manual (10.0.0.250/24)
DMZ interface config:
Addressing mode: manual (192.168.16.1/24)
[Code].....
View 5 Replies
View Related
Nov 26, 2011
I just bought a WRVS4400N last week to replace my existing LinkSys WRH54G. To my disappointment, I now have a problem that this router halts everytime any eMule/P2P client is connected for more than 15~30 minutes, no matter the uPNP is enabled or not, When it halts, the only thing to get it work is to unplug its power cable then back on. So, I then upgraded its firmware from 2.0.1.3 to 2.0.2.1, but the problem still persists. However, the truth is that this problem never happened on my WRH54G
View 4 Replies
View Related
Feb 13, 2013
I would like to get using of course SNMP, list of client IPs connected to VLAN in Cisco Catalyst 3600.So far, I have pseudo-algorithm made by me which obtains those IP addresses, but I am not sure if this is done in right way :
1) Receive all IP addresses from Catalyst using oid 1.3.6.1.2.1.4.20.1.2. I get something like :
IP-MIB::ipAdEntIfIndex.10.10.2.1 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.2.251 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.3.251 = INTEGER: 151 and so on.
2) Get ifIndex of VLAN (oid 1.3.6.1.2.1.4.20.1.2.10.10.2.1.<IP_ADDRESS>) for particular IP address from above list :
IP-MIB::ipAdEntIfIndex.10.10.2.1 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.2.251 = INTEGER: 152
IP-MIB::ipAdEntIfIndex.10.10.3.251 = INTEGER: 151
3) Get VLAN name (oid 1.3.6.1.4.1.9.9.46.1.3.1.1.4.1.<IF_INDEX>) If_index is borrowed from list above :
IP-MIB::ipAdEntNetMask.152 = No Such Instance currently exists at this OID
IP-MIB::ipAdEntNetMask.151 = No Such Instance currently exists at this OID
In the third step I have this problem, that instance can not be found in OID. It is weird, because for about forty IP addresses i can find about their 10 VLAN names to which they are connected.
View 1 Replies
View Related
Jul 18, 2011
My network connection was vanish the client are not connected to server and the computer cannot access internet
View 1 Replies
View Related
