I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc.
View 3 RepliesI'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies View RelatedWe have some older Honeywell Dolphin 7900 Series Handhelds that have issues with wireless communication. Very unreliable communication. One recommendation from Honeywell is to disable the G standard and only allow B. Basically have a WLAN that is solely b radio enabled. I see that their are options to go B/G only or A only, but no options in the radio policy to go B only.
We are using WCS 7.0.240 and the controller is a WLC 5508 running the same code revision.
Is this doable on a single WLAN while leaving G available on other WLAN's?
Is it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?
View 2 Replies View RelatedWe use WLC 5508 with 7.4. We tried to set max allowed clients per AP radio to 30 through GUI. We have APs with 80 clients associeted though.
When entering config wlan max-associated-clients max-clients wlan-id we got
"WLAN/Guest-Lan/remote-lan is enabled. disable to configure max associated clients."
GUI doesn't show that message, should it? In GUI, Is it necesary to disable WLAN before too?
Background: Wireless credit card machines can't stay connected to the 5508 controller 7.0.116 / 1142 ap wireless system. MAC address of one of the wireless hosts is 00:12:0e:ec:ce:97. AP servicing them is d4:a0:2a:99:34:60. Hosts are able to connect to the network after a reboot and stay connected for random periods of time but then don't come back unless you manually reload them. I have 3 in total in the same room services by the same ap.
I have the output of debug client 00:12:0e:ec:ce:97. Output showed 802.1x 'timeoutEvt' Timer expired for station 00:12:0e:ec:ce:97 so I increased the value to 4000ms on the controller but am still having the issue.
Note that the output below is the state the client stays in after receiving the timeout (802.1x 'timeoutEvt') showing subsequent attampts. The only way to get them back on is a reload of the credit card machine.
[Code]........
I've got a setup like this:
WLC 5508 v7.0.98
6-7 Autonomous upgraded to lightweight APs - 2 * 1231G while the rest are 1242AG
3 dynamic interfaces, 2 to Corp (diff VLANs) and 1 to Guest
4 WLANs binded to different interfaces
2 to the Corp interface Vlan X
1 to Guest
1 to Corp Vlan Y
DHCP for Corp is provided by their own Win DHCP server while controller is the DHCP server for Guest. Lease time is 1 day.
My problem now is, some clients, at random, loses their IP after being connected to the network. They get a 169.254.x.x. They connect to the Corp network OK, no browsing issues but after a while, they lose their IP address.
They can either wait for a while before getting an IP back or just simple renew their IP on their machine.
I've tried increasing the threshold values in the Local EAP to double its default values and also setting the WLAN session time out values to infinite. However, these 2 didn't work. I'm still having clients that occasionally lose their IPs at random.
I've also noted that this affects clients with WZC wireless drivers and not others e.g. Intel Proset.
I have a DHCP server on a WLAN that does not support Cisco's native proxy mode. I need to use DHCP bridge mode for that WLAN only.
How do I disable DHCP Proxy and switch to DHCP bridge mode for one WLAN ?
I have been trying to manually disable clients from within WCS by calling up the client in 'Monitor Client' and then in previous versions you used to be able to select 'Disable Client' from the drop down list. This would take you to the template page where you would deploy this to the controller(s). It's not there anymore in my version. It means you have to do it manually, which is really annoying.
View 3 Replies View RelatedSince the SW upgrade to version 7.3.101.0 (wlc 5508) i have the following issue. We have a W LAN with 802.1x (WPA2/AES) secured. Before the update the users need to enter user/ PW every time when they reconnect (W LAN switch off/ on again) to the W LAN. Now the users don`t need to enter user/ PW when they reconnect to the WLAN.
I could not find any setting on wlc to clear this issue.
I have a guest wireless network setup on a 5508 WLC using 7.2.103.0 firmware. Under my guest WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected, "over-ride global config" as check marked, "web auth type" as "customized(downloaded), "login page" and "login failure page" as "login.html" selected.
I haveI have 4402 WLC's using 7.0.116.0 firmware throughout my company that anchor back to the 5508 for the guest network. The 4402 WLC have the guest network configured as WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected.
I would like to disable the HTTPS for the logon screen and I am not sure what steps need to be done for this. I researched and found the command "config network web-auth secureweb disable". I set the command on the 5508 only and rebooted. When I tested I got a blank webpage with "http://1.1.1.1/fs/customwebauth/login.html?switch_url=http://1.1.1.1/login.html" in the address bar and had no way of clicking the accept button to get to the Internet.
Everything works fine again if I enter "config network web-auth secureweb enable" and reboot. Do I need to run the "config network web-auth secureweb disable" command on all the 4402 WLC's that are anchored to the 5508? What could be breaking my login.html page while using only http?
I have WLC 4400/5508 I stumbled across this config paging disable command to stop page breaks, works great for the one session I am logged in but it do not work for other users..
View 1 Replies View RelatedCan the Cisco 3602 APs be configured by a Cisco 5508 WLAN controller to provide client isolation?
View 2 Replies View RelatedStrange issue that our support staff is seeing on our guest WLAN. I have 2 wlans, 1 is production and authenticates our Domain controllers, this is working fine. The other is a wlan that has restricted access internally, I allow http, https and VPN access out only.
It appears that on the guest wlan, after random amount of time an established VPN connection using Cisco VPN client disconnects. Wireless connectivity doesnt appear to go down, just the vpn connection.
On this guest wlan, I have configured QOS bronze and I read a link where this may be affecting the UDP conversation between VPN client and end point.
We have a 5508WLC recently updated to 7.2.110.0 since we are using CAP3602I-N-K9, this AP is intended to work as a H-REAP device and eventhough it is registering to the controller I can't get to see the WLANS on the list to map it to the local VLANS
I have verified and the WLAN is configured for local switching also have followed the steps listed here:URL
Still Can't see the WLANs under the Flexconnect tab on the AP?
We are moving forward with a mobility project which requires our network to authenticate/authorize based on certificates.
WLAN_1 has 802.1x enabled passing the cert through to the MS CA which authorizes the cred, which in turn passes the AD creds of the user to the MS RADIUS server for authenticate/authorization.
Hardware: WLC 5508 running 7.2.110.0 3600 APs ACS 5.2 not used for AAA
1. As we turn up additional SSIDs, we need Mobile SSID to accept ONLY the Mobile Cert, our Internet SSID to only accept the Internal Cert and our GUEST SSID to deny ANY Cert issued by our CA.I know ISE makes this much easier, but I dont have it and need this to work as best we can until next fiscal cycle..
I've been asked to generate some report data on a specific WLAN, a limited access WLAN that was added recently. We need to be able to report on "Average and Peak Number of clients (Total)" and "Total Bytes Transferred (all APs)" on a per site basis. The sites involved mainly use 4402 and 5508 WLCs managed by our WCS server. Is there anything on WCS where we can easily get this information (on a monthly basis).
View 1 Replies View RelatedWe are having 5508 controller with Lightweight access points 1142, IS it possible to disable 802.11a on certain access points before turning it off completely on the controllers?? Could you provide steps for doing so on WCS?
View 5 Replies View RelatedI have a WLC 5508 with half a dozen LAPs (AIR-CAP3502I-E-K9).They have been working but sometimes clients detect conectivity problems with the wlan.Here is the message log I can obtain from the controller:
View 1 Replies View RelatedI am trying to apply WLAN template from NCS to two WLCs 5508 and I receive this message."Another WLAN with same SSID and either WPA1/ WPA2/ WPA1+WPA2 is enabled. Please change the Layer 2 security policy."The template has layer 2 security with WPA+WPA2 enable and 802.1x.I have other WLAN template with other name and other SSID with the same security policies with no problem to apply.
View 2 Replies View RelatedIs there any way to determine how much bandwith users on a particular WLAN (Guest) are using on the 5508 or by any other means?
View 9 Replies View RelatedWe’ve recently installed a 5508 w LAN controller for my organization wireless network and each time devices connect to this wireless network they receive an ip conflict error. All devices conflict with the ip address of IP address 0.0.0.0 with mac address 00-00-00-00-00-00.
All devices event viewer has this TCP error: “The system detected an address conflict for IP address 0.0.0.0 with the system having network hardware address 00-00-00-00-00-00. Network operations on this system may be disrupted as a result.” We previously experienced the same ip conflict with 12000 w LAN network that he had used as proof of concept.
We are implementing a new corporate headquarters and have bought a Cisco 5508. I have two connections plugged into the 5508 in ports 1 and port 2. Port 1 is for all internally wireless networks and connects to our core 6500 and use an external DHCP server scopes. Port 2 is for our guest WLAN and connects directly to a public network switch in front of (outside) the firewall. For the guest network, I have setup a vlan on the controller for dhcp and the interface setup to that vlan and dhcp scope built on the controller. how or can I NAT the internally addressing for the guest network to the public IP address on the controller. Essentially I want to drop of guest network traffic outside the firewall and not have to deal with setting up the firewall for any aspect of guest network traffic.
View 1 Replies View RelatedOn a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
My PC is hardwired to a Comcast all in one Internet/Phone Modem/Wireless Router. I have installed new software on my Android Phone that can control my music recording software over Wi-Fi. Here is the rub: Recording software and the Internet don't play nicely together. They are in constant conflict for resources. I used to simply disable my network connection when working in my recording software. This obviously won't allow my phone to connect to my computer . Is there a way to disable my Internet connection yet remain connected to my network? I don't want to disable the entire networks Internet connection since there are other Internet users on the network.
View 5 Replies View RelatedI have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network. Because there is one area we cannot layout the cable. How to add the repeater and how to configure the repeater in wlan controller network.
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.
I have 350 WAP (1142n) running of two WLC 5508 (IOS version 7). WLCs are not located on the same subnets/locations and are not configured as mobility groups. The vlan ids on both wlcs are not identical.
[Code].....
I've got a couple new 5508 controllers to replace my 4404's. Im wondering though if I throw them on the network to setup, will there be any conflict with the current access points? Will they try and join the new controllers for any reason automatically? Is there a better way, or a best practice to provision these new controllers?
View 3 Replies View RelatedI have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedI have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies View RelatedI have a wlc 5508 and I'd like to setup a network for visitors. They will connect to the WLAN, enter a password and then automatically get redirected to an external website. I understand the wlc 5508 supports this but I'm struggling to find out how to set this up I assume this can be done without having to customise webauth bundles?
View 2 Replies View RelatedI've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies View RelatedI would like to set a time limit for how long a client can be continously connected to the WLAN that provides my guest internet access. The user name/password is hosted on my ACS and authentication is provided by my Cisco NAC. I am using 5508 controllers (7.02) and WCS.
Somewhere in this combination of stuff, there has to be a way to set a two hour time limit.