I have WLC 4400/5508 I stumbled across this config paging disable command to stop page breaks, works great for the one session I am logged in but it do not work for other users..
View 1 RepliesWe use a phone system that requires SIP Application Layer Gateway to be disabled on the router. We replaced the older RVO42 routers with the WRVS4400N routers and the VOIP phone works fine with this check mark option disabled.
Does the new RVO42 router allow you to disable this option? I did not find it in the manual so far. I do not want to buy two routers and find that it will not work with the phone system. We need Dual WAN this time so I thought we would try RVO42 model again as long as it is the latest version. Any issues with newer RV042, RVO82 with NEC VOIP phone systems?
I am replacing an old 4400 series WLC running version 4.0.179.11 to a new 5508 WLC running version 7.2.110.0.
We currently have 70 x 1131 Access points on the 4400 WLC.
With this upgrade, do i need to upgrade the old 4400 to version 6.0 so the AP's get an up to date IOS or can i directly migrate all AP's over to the new 5508 without any version incompatabilities on the AP's?
I am abit worried that the AP's are running a very old IOS on the 4400 v.4.0.179.11 to go straight to the new 5508 v.7.2.110.0.
I want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Can I make that jump or should I do incremental?
View 7 Replies View RelatedCurrently in the process of migrating from psk to 802.1x radius environment using a mix of 4400 and 5508 controllers with WCS using Microsoft ias. The problem I have is there is a lot of shared iPads and tablets in the environment. Is there a way to force these user to relogin to radius after a certain time period so they are not sharing unames and passwords?
View 1 Replies View Relatedmy internet connection is just connected to a router , it is OK to always disable and enable my internet connection? because every time i open my PC i always disable and enable the internet connection to make it work. how to make my internet connection work properly every time when i open my PC?
View 4 Replies View RelatedI want know if it's possible with a script enable disable wifi, without every time login to router.
View 1 Replies View RelatedI have ASA5505 as my main router (192.168.15.1) and it currently it also serves as DHCP server. I have a WNDR3700 (192.168.15.2) which work as an access point and it provide wireless access for wireless devices. I have few dhcp clients where i can't setup static IP, and i want to restrict them to use static IP through MAC reservation.
1. Make ASA5505 to do the MAC reservation f, which will be easy setup for me. But as per my search its not possible.
2. Disable dhcp on ASA and enable dhcp on my WNDR3700. i tired this and dhcp clients are getting IP from wndr3700, but the problem is dhcp clients gateway defaults to 192.168.15.2 (as well as dns) and therefore no internet connection.
I received WAP4410N-G5 AP with 2.0.2.1 firmware and set up it very easily. Never experienced a single signal drop in a few days.
After updating firmware to 2.0.4.2 version I am completly unable to make any changes! If I press on "Enable" or "Disable" all settings will be lost after I apply them and neither "Enabled" nor "Disabled" is selected.
Had to revert back to 2.0.2.1. Is my AP faulty?
I start my pc i get 2 local area connections instead of 1 and because of this my internet does not work unless i disable and enable again the network .After enabling only 1 network shows and i can connect to internet.It may be because i replaced my motherboard even tho i uninstalled the drivers?
View 1 Replies View RelatedIn my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink) i.e. whenever there is some problem at a specific port. I need to monitor it through an OPC server and right now what i am doing is as follows: i am using Kepserver and i have added SNMP driver in it for that purpose i am not a networking expert but what i have learnt till now is that SNMP agent (that resides in switch) delivers the status of MIBs to SNMP manager ( which in my case is kepserver (opc server)) for the above purpose i am adding IF-MIB to monitor OID 1.3.6.1.2.1.2.2.1.8 (which shows port statuses) but when i add that in OPC server then it indicated that this OID is not available in the Switch ( it might be disabled) so i need to ask if there is any way to enable OID's in a switch,
View 0 Replies View RelatedI`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.
View 5 Replies View RelatedCurrently have a 5508 in the lab and testing 4 AP's with it. Eventually there will be 18 AP's spread thru out different floor in our building.
So far access is working fine using WPA, 802.1x and the client configured to use windows logon credentials..But it doesn't seem to automatically transfer between access points.
When disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other wireless laptop get disconnected. And when you try to connect, it doesn't connect again.
View 3 Replies View RelatedI have an EA6500 wireless router and i have to constantly disable / enable the guest wireless access to get it working again. It might work some time less than a day but then it fails. I tried to set the wireless channel manually instead of auto and the same issue is happening. The private wireless ssid works just fine. I have the latest firmware.
View 9 Replies View RelatedFor 3 years now, I've been using an NME-AIR-WLC25 controller with an ever-increasing number of AP's (reaching the 25 limit a few months ago). As part of a new construction project, I'm adding 5 more AP's onto my network. As a result, I purchased a 5508 controller with a 50AP license to get me started.
My question is simple-- is it possible to import the WLC25's configuration to the 5508? I have a feeling the answer is no, but I figure it can't hurt to ask, and if I'm lucky it will save me quite a bit of time configuring this new controller.
I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
Wlc 5508
Ap 1242
7.0.220.0
I have a guest wireless network setup on a 5508 WLC using 7.2.103.0 firmware. Under my guest WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected, "over-ride global config" as check marked, "web auth type" as "customized(downloaded), "login page" and "login failure page" as "login.html" selected.
I haveI have 4402 WLC's using 7.0.116.0 firmware throughout my company that anchor back to the 5508 for the guest network. The 4402 WLC have the guest network configured as WLAN>security>Layer3 tab I have "layer 3 security" as "none", "web policy" as check marked, "passthrough" selected.
I would like to disable the HTTPS for the logon screen and I am not sure what steps need to be done for this. I researched and found the command "config network web-auth secureweb disable". I set the command on the 5508 only and rebooted. When I tested I got a blank webpage with "http://1.1.1.1/fs/customwebauth/login.html?switch_url=http://1.1.1.1/login.html" in the address bar and had no way of clicking the accept button to get to the Internet.
Everything works fine again if I enter "config network web-auth secureweb enable" and reboot. Do I need to run the "config network web-auth secureweb disable" command on all the 4402 WLC's that are anchored to the 5508? What could be breaking my login.html page while using only http?
I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies View RelatedI have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc.
View 3 Replies View RelatedWe have some older Honeywell Dolphin 7900 Series Handhelds that have issues with wireless communication. Very unreliable communication. One recommendation from Honeywell is to disable the G standard and only allow B. Basically have a WLAN that is solely b radio enabled. I see that their are options to go B/G only or A only, but no options in the radio policy to go B only.
We are using WCS 7.0.240 and the controller is a WLC 5508 running the same code revision.
Is this doable on a single WLAN while leaving G available on other WLAN's?
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedI have a Cisco 5508 controller and am considering using LAG. Can I enable LAG but only use 2-4 of the 8 available ports on the 5508? I am asking because currently I don't have enough ports on my 3750G switch to accomidate all 8 ports on the 5508.
View 2 Replies View RelatedI am trying to block clients based on MAC addresses connecting to our Wireless Guest network.
My scenario is: We have 2 interfaces (corporate and a guest). Users are connecting to our guest network after they have automatically connected to our corporate network and logged into Windows. When they realise that things are not quite working in the way they want (access to servers etc...), they reboot and then find they cannot logon to the laptop at all. This is because the laptop has automatically rejoined the guest network and has no access to AD. I then have to locally logon to the laptop and remove the guest network.
It’s starting to become a bit of a pain as we are an educational establishment and... well... you would wouldn’t you
Hardware: WLC5508, Software Version 7.3
So far I’ve tried enabling MAC Filtering under “Security -> AAA -> MAC Filtering”, but found out that it’s a white list. The opposite of what I’m trying to achieve, but I like the fact you can link it to a specific interface.
I’m just looking at the “Disabled Clients” again under “Security -> AAA ->”, but think this is more a total ban as I cannot see a method at attaching it to an individual interface. I'm kindda stuck and my good old friend Google is not yielding great results.
I’m not by any means a wireless expert, so there is probably a better method. I would prefer to use the controller as a way of achieving this, but if you think I’m wasting my time and should be looking at a Windows Group Policy method then I’ll go with that?
Is it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?
View 2 Replies View RelatedWe are having 5508 controller with Lightweight access points 1142, IS it possible to disable 802.11a on certain access points before turning it off completely on the controllers?? Could you provide steps for doing so on WCS?
View 5 Replies View RelatedJust tried to setup my wireless adapter and after it tells me to plug in my adaptor I get.Wireless adapter setup requires that wireless connections are managed by Microsoft windows.
Error Description: Other Wireless Manager
Model Name: AE1000
Operating System: WIndows Vista SP2
Software Version: 1.2.10104.2
I looked all over my computer I can not find any other wireless manager on my system nor could I find a way to enable or disable windows wireless manager.
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies View RelatedWe`re using a WLC 5508 with SW 7.2.103.0.The most things are working fine, but i have a problem with the web auth.
Setup:
- Max Concurrent Logins for a user name is set to 1
- Max-Login Ignore Identity Response is set to enable
- Web Authentication Type is set to customized
The Problem:
- the user "test" is logged in at device1 (working), the same user "test" try to login at device 2 (is not working, fine!) -> login is not accepted, WLC redirects to the INTERNAL Web Login Page.The problem is the redirect to the internal web login page after failed login. If i try to login with a not existing user, the redirect is working perfect to the customized web login.
I had configured one access point CAP3602E in flex connect mode through a WLC 5508 after deploying the access point in flex control mode the local mac-filering is not working. before it was working when ap was in local mode. any body have to know is the mac-filtering working in flex-control mode ?
View 2 Replies View Relatedi have a WLC (5508) - trying to enable AP group vlans based on instructions from: url...however, my problem is that i don't have the 'ap group vlans feature enable' checkbox.
View 1 Replies View RelatedI have several WLC 5508 with 7.2.110 firmware. My questions are:
(1) Is band select is enable by default on 7.2.110?
(2) All the variables settings on the band select, how do I set it up to make 5 ghz more preferable than 2 ghz?
(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.