Cisco :: Migrating APs From WLC 4400 V.4.0.179.11 To WLC 5508 V.7.2.110.0
Jun 11, 2012
I am replacing an old 4400 series WLC running version 4.0.179.11 to a new 5508 WLC running version 7.2.110.0.
We currently have 70 x 1131 Access points on the 4400 WLC.
With this upgrade, do i need to upgrade the old 4400 to version 6.0 so the AP's get an up to date IOS or can i directly migrate all AP's over to the new 5508 without any version incompatabilities on the AP's?
I am abit worried that the AP's are running a very old IOS on the 4400 v.4.0.179.11 to go straight to the new 5508 v.7.2.110.0.
View 3 Replies
ADVERTISEMENT
Feb 5, 2013
We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?
View 5 Replies
View Related
May 30, 2013
We currently run six 4402 Wireless lan controllers - these are managed by a WCS server - soon to be replaced by Cisco Prime. We run a mixture of LAP1242 and LAP1142 wireless access points. I need to add more but have been told by my supplier that the both these AP's are now end of sale and cannot be purchased.
The replacement AP's are the 2600 series - but I have been told that these are not compatible with my existing 4402 controllers.
To make matters worse I was then advised that if I purchase the new 5580 controllers the older LAP1242 access points will not work with it and require replacing - this, for me, is a lot of access points.
What I need to know is:
What access points, if any, are currently available that are compatible with my 4402 controllers and a future 5508 installation?
I ssem to be in a situation now where I cannot buy any access points that will work with my 4402's but if I upgrade all my current 1242's will not funtion with the new 5508 controller!
View 9 Replies
View Related
Jan 23, 2012
for some reason our wlan-controllers were build up to be standalone instead of beeing one mobility-group. I would like to change this in order to use all features of HA.
let me describe our scenario: two WLCs 5508 running SW ver. 6
- same subnet
- both are running in master controller mode
- different hostnames, ip-addresses, etc
- all settings for WLANs and AP-groups (exept the APs themselves in these groups) are the same
- in total at this moment we are running around 100 LAPs configured one half on WLC#1, the other half on WLC#2
I don't know exactly why, but when that setting was installed, someone already configuredHA for each accesspoint... e.g.:
- AP#1 primary WLC#1, secondary WLC#2
- AP#2 primary WLC#2, secondary WLC#1 but without WLC#2 knowing the configuration for AP#1 it makes no sense, correct?
so my question is: how should I do the migration in the best way?
is it easy as:
- disabling master controller mode on WLC#2
- configuring both WLCs into one mobility group
--> WLCs are negotiating their configurations for the APs
View 5 Replies
View Related
Aug 26, 2012
I'm working on migrating autonomous WAPs to lightweight mode in a WLC 5508. Some of the older WAPs are being decommissioned at the same time.
One issue I have found is that after replacing an old WAP in autonomous mode with a new WAP (3502); some clients near the coverage of this new LWAPP are now connecting to another WAP in autonomous mode that has not been converted or replaced yet; but that is located quite far away from where these clients are, actually two floors down. Users on these clients have reported wifi dropouts, which is obvious due to the distance where the old WAP is. A workaround that seems to work is removing the wifi profiles in the client machines and recreating them again, which is not a good solution for all of the wifi profiles we have in place. At this point of time we still need to have the older WAPs until they are all replaced.
How can I get clients connecting to a LWAPP that is closer to their location? I'm wondering what causes those clients to look for an existing older WAP rather than connecting to the new LWAPP, which is broadcasting the same SSID closer to where they aree. Bear in mind that the new LWAPP is working fine and has live sessions working just fine.
View 5 Replies
View Related
Apr 2, 2012
I want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Can I make that jump or should I do incremental?
View 7 Replies
View Related
Mar 28, 2012
Currently in the process of migrating from psk to 802.1x radius environment using a mix of 4400 and 5508 controllers with WCS using Microsoft ias. The problem I have is there is a lot of shared iPads and tablets in the environment. Is there a way to force these user to relogin to radius after a certain time period so they are not sharing unames and passwords?
View 1 Replies
View Related
Oct 19, 2011
I have WLC 4400/5508 I stumbled across this config paging disable command to stop page breaks, works great for the one session I am logged in but it do not work for other users..
View 1 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Jan 22, 2011
We are pulled the plug on our PIX 501 as its not letting us use all 100Mbit that our cable provider is now piping to us. I read the conversion guide but it made no mention of the 501's. Only the 515's or newer.The ASA5505 is putting up a little bit of a fight (This what I get for failing my CCNA??)After refusing to configure the LAN ip address to something other than what it was shipped with, I broke down and connected to the management console and forced an IP address on the LAN side. Now I reset my default config and everyone can get on the internet.Until the ISP cuts you off because you forgot to set your static IP. Oh, and by the way, they dont support Cisco gear.
When I attempt to assign the IP to the outside interface, it accepts without a hitch, but everything grinds to a halt. I cannot have this, as I have off-site users that operate with dedicated ports using Remote Desktop. I've attempted to set the IP via both ASDM and management console. I've tried setting a static route, but that doesnt give me any love either. Im running ASA Version 8.2(1) and ASDM Version 6.2(1)Once I get the static IP set and working properly, I can tackle moving the port configs.
View 10 Replies
View Related
May 29, 2012
we are running acs 4.2.0.124.16 on cisco appliance 1113.We need to uprade it to 4.2.1.15 which is the latest release.and need to know the dependencies whether any license required?
View 6 Replies
View Related
Feb 18, 2013
I need to migrate DFM alarm settings data from LMS 3.1 to LMS 4.2.3 and I want to use this method, [URL] , to extract the data from 3.1 and then inport it into 4.2.3.
I successfully performed it for IP settings, it was easy since the data format was the same.
But the format differs quite alot for Interface and Port data, here is an example:
export from LMS 3.1
IF-hostname/17 [Gi0/0.524] [10.55.254.3]; INTERFACE:;IF-hostname/17; MANAGED_STATE:;EXPLICITLY_UNMANAGED
export from LMS 4.2.3
INTERFACE:IF-hostname/17 MANAGED_STATE:MANAGED GigabitEthernet0/0.524
It looks like I have convert interface names, sort and delete stuff to make it look the same.
View 1 Replies
View Related
May 8, 2013
[URL] it mentions that migrating from NCS 1.1.2 to CPI 1.2 isn't possible.
How can I get around this?
View 3 Replies
View Related
Jan 28, 2011
I have recently migrated from a PIX 515e to an ASA 5510. In the main this was successful. However, I have a number of L2L VPN's (all connecting to Cisco PIX 501 or 505). The majority of these VPN's are working fine. However, I have a couple of VPN's that are causing me a problem. It seems like the tunnel is established for anything between 10 minutes and 4 hours before going 'down'. I cannot initiate the tunnel again from the hub end (ASA 5510) of the VPN.However, if the remote end reboots the PIX, the tunnel is re-established.The ASA is running 8.3(1) and the remote PIX's will be running various versions of code but will all be 6.3(x). The strange thing here is that the majority of the sites are working and the config for each tunnel is identical other than the access-lists for interesting traffic and peer address.
View 7 Replies
View Related
May 7, 2013
for testing purposues i wanted to exchange a running ASA 5510 with a ASA 5505. I included the running configs from both the ASA 5510 and the new configured ASA 5505.
On the running ASA 5510 there is:
one interface for WEB
static IP xx.xxx.xxx.178
route 0.0.0.0 xx.xxx.xxx.177
[Code].....
View 1 Replies
View Related
Jan 4, 2012
I currently have the following set up (excuse my quick drawing):
--------------Vendors VPN Router----
| ------Cisco 3000 VPN------ |
| | | |
Private Network-------ASA5510---------Pub Switch------Cisco Router 2x T1
I've been tasked with migrating to the new ISP, which provides us with Cisco ME-3400E switch and /26 public subnet. I currently have 15 static NATs and 14 L-2-L VPN tunnels configured in ASA. Is there a way to configure additional Outside int on ASA and use it to migrate the existing VPN tunnels and static NATs? I'm trying to avoid downtime and hope to do it step by step. I'm thinking about adding additional Public switch, so I can also migrate vendor's router and VPN concentrator, which need to be in parallel to ASA. Assuming that this is possible I'd would like to do the following:
1.Configure and connect additional Outside Interface on ASA - public IP address and ACLs
2.Connect it to additional "Public switch", which would be configured with public IP address and connected to new ISP's Cisco ME-3400E.
3.Migrate my VPN tunnels and static NATs.
4.Migrate vendors equipment/VPN concentrator
5.Update my global NAT pool
6.Shut down old ISP
View 13 Replies
View Related
Feb 12, 2013
I have NCS 1.0 with 100 devices support license installed. Now knowing it has reached end of sale, and also for the fact that Prime does cover devices like routers, i went ahead to the upgrade path via PUT (Product Upgrade Tool). Finally I received an email (OBA) advising my order is ready. This email included two items in the shipment,
L-N-PI12-100-M=
NCS 1.0 to Prime Infrastructure 1.2 Minor Upg 100 Device
L-PILMS42-100-M
Prime Infrastructure LMS 4.2 - 100 Device Upgrade Lic
When i click to the link in the same email to download the license, it only shows me one file which is L-PILMS42-100-M I tried using this file and installing on the NCS1.0 but it gives me error that this file is not a license file. The license name suggests me that it is not the license to be installed on the NCS. The file should be L-N-PI12-100-M=
View 5 Replies
View Related
Mar 11, 2013
I have a situation here where after migrating from PIX 6.3 to ASA 8.4, VPN connection from window server 2003 and 2008 fail to connect. Strangely, win7 or win 8 works perfectly well.
It failed due to
reason=DEL_REASON-IKE_NEG_FAILED
The diff we can see is win 7 is 32 bits and the server client version is 64bits.
View 1 Replies
View Related
Aug 28, 2011
I am migrating my PIX configuration to ASA 8.4(2) with my old nat configuration.I don't want the traffic match ACL inside_outbound_nat_acl from inside interface with NAT [code]
when I configured "any" in "nat (inside,any)", I cannot type the "route-lookup" command but when I change like "nat (inside,outside)" then I can type the "route-lookup" command.so what's mean of "any" in this command?
View 10 Replies
View Related
Aug 7, 2011
I am migrating from Cisco 6509 IOS (12.2) to Nexus 7000 NX-OS (5.1(1)).I am looking for a equivalente NX-OS command for permit ipinip on IOS.
View 2 Replies
View Related
Apr 18, 2011
I have a 7.0.164.0 WCS that I am trying to upgrade to 7.0.172.0 In the system infrastructure we have three 4400-50 controllers with a total of about 90 access points (1231's, 1131's, 1142's, and 3500's) The server is a VM with 2GB of ram and about 4GB of free hard drive space (the WCS software is installed on the D: partition). The WCS installer goes through the initial setup and gets to the point of "Migrating Data" and basically stalls. I started the upgrade Friday at 11:30AM and finally killed it at about 9:00AM on Monday (almost 3 full days).
I then uninstalled the partial 7.0.172.0 installation, and also uninstalled the 7.0.164.0 installation. I then did a clean install of 7.0.164.0 and imported my backup. After i verified that everything was working correctly I then tried the 7.0.172.0 upgrade again. Currently its almost at 24 hours of sitting at "Migrating Data"
View 10 Replies
View Related
Jun 13, 2007
Is there any way to auto migrate my 3030 VPN configuration to an ASA platform?
View 3 Replies
View Related
Jul 4, 2012
migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;
[code]....
View 5 Replies
View Related
Sep 28, 2011
One of my clients has an older 3745 running IOS 12.3 and we are looking at replacing it with a new 3945 that runs IOS 15.0. This router is also configured with CME. Is it possible to migrate the current 12.3 config to load on the new 15.0 IOS? This will be my first encounter with 15.0 so I don't know what I am up against at this time. I am just hoping I don't have to retype all the ephone config, dial-peers, etc
View 2 Replies
View Related
Dec 4, 2012
We have 2 separate ACS 4.0 servers installed on windows 2003 server(2 separate location) Both these servers are Integrated with Cisco WLSE and Corporate AD.
Now, we are planning for Migrating to ACS 5.4 on VmWare ESXi 5.1. And need to Integrated with Cisco WLSE and Corporate AD.
Can we import the datas from 2 x ACS 4.0 server to this new Single ACS 5.4 vmware server?
View 7 Replies
View Related
Apr 15, 2011
We have the acs server which has the ssl certficate(certifcate authority) running in acs 3.2 windows version for eap-tls enduser authentication.
We want the same to be migrated to acs 4.2(appliance) application. I have tried in different ways to push the certificate but i couldn't.
I have tried Thru System Configuration --> ACS Certificate Setup --> Install ACS certificate --> Download certficate file In that i have mentioned the FTP server IP address, credentials, path and file name
But if i submit the request its giving the directory not found or credentials wrong.
In FTP logs its showing like this
Apr 15, 2011 19:41:55 Session 4, Peer 10.190.249.40 PASS welcome2acsApr 15, 2011 19:41:55 Session 4, Peer 10.190.249.40 230 User logged inApr 15, 2011 19:41:55 Session 4, Peer 10.190.249.40 FTP: Login successfulApr 15, 2011 19:41:55 Session 4, Peer
[Code].....
View 2 Replies
View Related
Oct 9, 2012
I have two link on two edge routes from same ISP for Active/Standby. I am using the private AS and ISP provided IPs, now i got own Public IPs and AS number. I want to publish my IPs and migrate the AS number from private to Public. But currently i do not want migrate my device IPs. just want to publish network and ASN.
current config is :-
Router 1
router bgp 64530
no synchronization
bgp log-neighbor-changes
[Code].....
View 12 Replies
View Related
Mar 18, 2013
We are currently running a ACS 1113 with version 4.2 software. We are going to replace the 1113 ACS with two 1121 ACS.
View 1 Replies
View Related
Apr 17, 2011
how to migrate the db from acs windows 3.3 to acs appliance 4.2.15.We are replacing win 3.3 to appliance 4.2.15 as a part of end of life. So we have the eap-tls/peap authentication.It has the huge records. So suggest me the steps to migrate the db from win 3.3 to appl 4.2.15.Do we need to upgrade to win 3.3 to win 4.0 to win 4.2 & then to migrate to appl 4.2 ?
View 4 Replies
View Related
Feb 4, 2013
We have an existing network with a core 6500 as a VSS connecting 4 buildings with 4500 chassis under which number of L2 switches are connected. Currunlty we are using RSTP in ring for redundancy but we want to use OSPF in LAN for faster conversion.All the VLAN's are created on 6500.
View 4 Replies
View Related
May 30, 2013
I'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies
View Related
Aug 7, 2012
I want to migrate a Cat 6503-E VSS to Cat 6509E VSS. We plan to use the same supervisor that we have on the Cat6503E, for minimizing the configuration change on the Doing this, the vss link will need to be changed, due to the fact that the supervisor slot will change with the Cat 6509, slot 5 instead of 1.
Question: is there a way to just change the vsl-link interface on a existing VSS ?
View 3 Replies
View Related
Sep 26, 2012
On our ISA server we have some publishing rules with the option "Requests appear to come from the ISA Server computer". This allows us to forward incoming external traffic to a network that is not directly connected to the ISA Server internal interface. We need this because our internal server does not know the route to the internet client but does know the route to our ISA Server, so the internal server sends his response to the ISA server and he sends it to the internet client.
View 1 Replies
View Related
