Cisco WAN :: Migrating Router Configuration From 3725 To 3945e

May 30, 2013

I'm trying to migrate the running-config from our old 3725 router to our new 3945e router.  Almost all of the config is copied over except for a few lines that come up as unrecongnized commands.  So it looks like these commands were either removed or changed to something new.

View 12 Replies


ADVERTISEMENT

Cisco WAN :: 3745 / Migrating Configuration To New Router With Different IOS?

Sep 28, 2011

One of my clients has an older 3745 running IOS 12.3 and we are looking at replacing it with a new 3945 that runs IOS 15.0. This router is also configured with CME. Is it possible to migrate the current 12.3 config to load on the new 15.0 IOS? This will be my first encounter with 15.0 so I don't know what I am up against at this time. I am just hoping I don't have to retype all the ephone config, dial-peers, etc

View 2 Replies View Related

Cisco WAN :: 3945E - Configuration For 20 T1 / E1

Sep 28, 2011

Does following configuration is responding to the request of my client asking for 20 T1/E1 connections on a Secure ISR 3945E, by combining on the same router One (01) NM-8CE1T1-PRI card and Three (03) HWIC-4T1/E1 cards.
 
Here are the router configuration:
 
CISCO3945E-SEC/K9           Cisco 3945E Security Bundle w/SEC license PAK                                   
MEM-3900-1GU2GB            1GB to 2GB DRAM Upgrade (1GB+1GB) for Cisco 3925/3945 ISR            
MEM-CF-256U1GB               256MB to 1GB Compact Flash Upgrade for Cisco 1900,2900,3900           
NM-8CE1T1-PRI                     8 port channelized T1/E1 and PRI network module                           
HWIC-4T1/E1                         4 port clear channel T1/E1 HWIC                                                        
SM-NM-ADPTR                       Network Module Adapter for SM Slot on Cisco 2900, 3900 ISR                 
PWR-3900-AC/2                   Cisco 3925/3945 AC Power Supply (Secondary PS)                                
CAB-ACE                               AC Power Cord (Europe), C13, CEE 7, 1.5M                                          
S39EUK9-15104M                 Cisco 3925-3945 SPE IOS UNIVERSAL                                                
PWR-3900-AC                      Cisco 3925/3945 AC Power Supply                                                   
3900-FANASSY                      Cisco 3925/3945 Fan Assembly (Bezel included)                                    
C3900-SPE250/K9                Cisco Services Performance Engine 250 for Cisco 3945 ISR                     
ISR-CCP-EXP                        Cisco Config Pro Express on Router Flash                                              
SL-39-IPB-K9                          IP Base License for Cisco 3925/3945                                                      
SL-39-SEC-K9                        Security License for Cisco 3900 Series

View 1 Replies View Related

Cisco Firewall :: Migrating PIX Configuration To ASA 8.4(2)

Aug 28, 2011

I am migrating my PIX configuration to ASA 8.4(2) with my old nat configuration.I don't want the traffic match ACL inside_outbound_nat_acl from inside interface with NAT [code]
 
when I configured "any" in "nat (inside,any)", I cannot type the "route-lookup" command but when I change like "nat (inside,outside)" then I can type the "route-lookup" command.so what's mean of "any" in this command?

View 10 Replies View Related

Cisco WAN :: Migrating Sup720 Configuration To Sup2T?

Jul 4, 2012

migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
 
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;

[code]....

View 5 Replies View Related

Cisco Firewall :: Migrating PIX515E To ASA5520 - Update BIN Files In Configuration For ASA?

Jul 18, 2011

I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1).  I have converted the config so that it is ready for the ASA.  I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files.  Do I need to update these or will they be updated when the ASA reboots with the new config?

View 2 Replies View Related

Cisco VPN :: 3945E ISR Router As EasyVPN Server / Local Usernames Restrict Management

Jun 24, 2012

I am using 3945E Router as Easy VPN Server, with 15.1 IOS. On router I have bunch on usernames for VPN authentication, I want to restrict Router management access for them(ssh,telnet, http and so on).

View 2 Replies View Related

Cisco WAN :: 3725 - Router Has Created 1035 Virtual-access But Have 85

Mar 2, 2011

I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router

View 1 Replies View Related

Cisco Switching/Routing :: HSRP Quirk On 3725 Router

Jun 4, 2012

I am setting up multiple vlan interfaces on a pair of HSRP Routers that will provide layer 3 routing for a network.  I am seeing this command sporadically show up in the router config mac-address-table static 0000.0c07.acd2 vlan 210
 
I am not entering this command.  So far, it has not shown up on the companion 3725 router.  I have a 2nd vlan I have just created and the problem hasn't shown up for that vlan as yet.Using C3725-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3) on the routers.

View 4 Replies View Related

Cisco WAN :: 3725 Router - Fans Had Rotation Error Reported

Jan 14, 2008

I have a 3725 router that is reporting the following syslog message:  

%FAN-3-FAN_FAILED: Fans had a rotation error reported.
 
When I do a show environment all, I am getting the following message:  

Fan status: Warning- low fan rpm condition detected.
 
Both the the fans are functional and are rotating fine. How do I repair?

View 6 Replies View Related

Cisco Switching/Routing :: Create Trunk Between 4507 And 3945E Router And Route Two VLans

Feb 12, 2012

i want to create a trunk between 4507 & 3945E router  & route two vlans from router 3945E
  
4507# vlan 99 & 51
# int vlan 99
# ip add 10.22.100.1/24
#int vlan 51
# ip add 10.22.103.1/24

[code].....
 
4507 version : IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
 
3945E: 15.1(2)T4 what I am missing?

View 3 Replies View Related

Cisco Switching/Routing :: 3725 Multiservice Router Maximum Flash Memory?

Jan 24, 2012

I read that there are internal and external flash memory in 3725 router that can max up to 128mb. So adding the sizes of internal and external flash memory, will that total to 256mb?
 
And also is the internal flash of 3725 just the same with its external flash?

View 8 Replies View Related

Cisco Infrastructure :: Removing Unused Virtual-access Interface On 3725 Router

Sep 8, 2004

I had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]

View 3 Replies View Related

Cisco WAN :: 3945e Udp Packets Are Dropping

Dec 13, 2012

I have a NAT setup. Some of my udp packets are dropping. How to find more about the NAT to find whether it missed anything or not. the router is 3945e. [code]

View 3 Replies View Related

Cisco WAN :: Can 3945E Support VRF-Lite

Mar 31, 2013

Can Cisco 3945E support VRF-Lite ?

View 4 Replies View Related

Cisco WAN :: Comparison Between 7204vxr Vs 3945E?

Oct 23, 2012

the feature difference between Cisco 7204vxr vs 3945E.
 
Wanted to know the limitation in 3945E compared to 7204VXR
 
Features39457204VXR with G2MemoryPacket processingBandwidth support 

View 1 Replies View Related

Cisco WAN :: 3945E And NM-8CE1T1-PRI Compatibility

Dec 16, 2011

I have inherited a 3945E router with an NM-8CE1T1-PRI card installed in slot 2 using the SM-NM adapter card. The command 'card type E1 2' has been issued but I only see interfaces Serial2/0:0 to Serial2/0:30.
 
Since it as 8 port card I was also expecting there to be
Serial2/1:0 to Serial2/1:30
Serial2/2:0 to Serial2/2:30
etc etc.......
Serial2/7:0 to Serial2/7:30
 
The router will not allow me to issue a sub slot number with the card type command.
 
Am I missing something in the configuration or is there an issue with this card and router combination? The show inventory has the following:
 
NAME: "Network Module Adapter for SM Slot on Slot 2", DESCR: "Network Module Adapter for SM Slot"
PID: SM-NM-ADPTR       , VID: V01, SN: FOCxxxxxxxx
 
NAME: "8 port channelized and PRI T1/E1 NM on Slot 2", DESCR: "8 port channelized and PRI T1/E1 NM"
PID: NM-8CE1T1-PRI     , VID: V01 , SN: FOCxxxxxxxx
 
It doesn't give any errors when booting up and the router is running c3900e-universalk9-mz.SPA.152-1.T.bin IOS.

View 2 Replies View Related

Cisco WAN :: Rack Unit For 7206VXR And 3945E?

May 29, 2013

I was looking for Rack Unit required for 7206 VXR & 3945E but couldn't find it.

View 1 Replies View Related

Cisco WAN :: 3945E Maximum Throughput Potential?

Jan 8, 2011

Am looking at purchasing a router that is capable of serving a WAN bearer at up to 1Gbps.  The 3945E has had good reviews as a high throughput router but the datasheets suggests performance of 350Mbps.  It also states that additional performance can be ensured by adding SPE modules. Whether the 3945E could achieve up to 1Gbps with SPE modules?
 
If the 3945E can't achieve such performance, The key features I am after are:
 
IPV4 and IPV6 support
L2tpV3 support
BGP
IP SLA
1Gb Copper Connections on-board with capability of at least 4 Ports

View 2 Replies View Related

Cisco WAN :: 3945 Vs 3945E From VPN Feature Perspective

Jan 20, 2013

I have an issue understanding the difference between 3945 and 3945E from VPN support perspective.
 
If you check this link here:
 
[URL]
 
You will see that the 3945E doesn't even have an ISM slot for a VPN ISM module and of course I could not find any ISM module for 3945E (I think this is obvious). Nevertheless, the above mentioned page and
 
[URL]
 
say "Embedded hardware-accelerated VPN encryption for secure connectivity" for 3945E 

That the Cisco 3945E supports the same VPN features (including packet encryption / decryption in hardware) like a Cisco 3945 with VPN ISM card?

View 1 Replies View Related

Cisco WAN :: 3945E - Terminate A 1Gbps Ethernet

Nov 15, 2011

I'm looking to use a Cisco 3945E to terminate a 1Gbps Ethernet internet connection and I want to know the realistic throughput that I can expect. The router will only be configured with BGP with partial routes. No firewall or QoS will be configured.

View 8 Replies View Related

Cisco WAN :: Traffic Shaping On 3725 With T1s?

Mar 15, 2011

I am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our  central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.

View 1 Replies View Related

Cisco WAN :: 3725 - 4GB Compact Flash

Sep 4, 2012

I have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity.  My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?

View 2 Replies View Related

Cisco :: 3725 IOS Image That Supports The Ip Sla Command?

Oct 19, 2012

any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.

View 4 Replies View Related

Cisco WAN :: 3845 / 3725 - Unable To Bring Up T1

Jun 27, 2011

I'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end.  On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
 
For some reason I'm able to bring up the T1's on the DSU/CSU WIC.  When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
 
CONFIG 3845 
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64

[code]....

View 2 Replies View Related

Cisco WAN :: 3725 / The Order In Which Packets Are Processed

Nov 12, 2012

I am implementing traffic export on the WAN interface of my 3725 router.  I use a dialer interface for PPPoE which is applied to the Fa0/0 interface.  This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS.  In what order would each of these items process a packet?  In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT?  How would QoS fit into something like this as well?  I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS. 

View 1 Replies View Related

Cisco WAN :: 3725 / Marking A Traffic With AF31

May 29, 2012

I have a Cisco 3725 router with IOS version "Cisco IOS Software, 3700 Software (C3725-ADVIPSERVICESK9-M), Version 12.4(12)". And this router is serving as a CE route for our MPLS connection to the service Provider. We do also have multiple VRFs ( around 10) and the WAN interface is DS3. So we created point-to-point subinterfaces and we put them in different vrfs. We have now transitioned to a new ISP and the ISP requested us to mark all of our outgoing traffics with DSCP AF31. So I have created the following policy-map
 
policy-map TRAFFIC-OUT-WAN-AF31
class TRAFFIC-OUT-WAN
  set ip dscp af31 
class-map match-any TRAFFIC-OUT-WAN
match any  
 
Now we do have multiple GRE tunnel interfaces sourced from one of the WAN subinterface ( which is a member of VRF A). So the moment I applied the the policy-map  on this WAN sub-interface (using the syntax "service-policy out TRAFFIC-OUT-WAN-AF31"), most of the GRE tunnels went down. And there is eBGP running on top of these GRE tunnels.

View 5 Replies View Related

Cisco WAN :: 3725 - Bonding 5 ADSL Lines

Aug 14, 2012

I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul.  We are currently using a Cisco 3725 and bonding the links via MLPPP.  This set up is working fine except that we are not getting the full 30Mb on the download side.  We are seeing more like 18 to 20.  I am wondering if we can acheive the full speed with our current set up or will we need something different to get the job done.

View 1 Replies View Related

Cisco Switching/Routing :: How Many Route Entries Does 3945E Or/and 3900 ISR G2 Support

Dec 1, 2011

I have a question concerning about how many ospf and bgp route entries does 3945E isr g2 router support?

View 6 Replies View Related

Cisco VPN :: 3945E-SEC/K9 And 2911-SEC/K9 Contains Advance IP Services Features (like Eigrp / OSPF)

Sep 11, 2011

I am wondering if IOS bundled  by default with CISCO3945E-SEC/K9 and CISCO2911-SEC/K9 contains adv. ip services features (like Eigrp, OSPF etc.).

View 1 Replies View Related

Cisco WAN :: 3945e / Client DH Key Range Mismatch With Maximum Configured DH Key On Server

Jan 19, 2012

what this syslog message means?  Being getting this on my 3945e series routers.  My gut tells me they are caused by our Security guys scanning my routers with invalid login attempts.
 
%SSH-3-DH_RANGE_FAIL: Client DH key range mismatch with maximum configured DH key on server

View 1 Replies View Related

Cisco WAN :: 3725 - Route-Map For Policy Based Routing

Feb 2, 2011

I have been using a route map to pick WAN exit points (PBR) on a 3725 router.  This have been working fine with /24 networks.  I am trying to pick the first /28 piece out of the 10.1.1.0 network and send it out a different exit from the rest of that network.  I have tried the /28 entry at the start and end of the route map, although I thought the first match would stop any further route map processing.  The entry does not seem to have any effect, as traffic from all addresses in the 10.1.1.0 /24 network exit per the "route-map 10-LAN permit 11" section.
 
access-list 5 remark Ten Dot 1 low 63 IPs
access-list 5 remark SDM_ACL Category=2access-list 5 remark Ten Dot One Low 63 IPs access-list 5 permit 10.1.1.0 0.0.0.63 log
[ code]....

View 11 Replies View Related

Cisco Switching/Routing :: 3945E - Bandwidth Percentage For Nested Policy Maps

Jul 15, 2012

I'm trying wrap my head around bandwidth guarantee for nested maps. I tried adding a new class to two of my policy-maps today, and got this error: 3945E-1(config-pmap-c)#bandwidth 3000 Insufficient bandwidth 3000 kbps for the bandwidth guarantee
 
I'm not sure how it knows that with the nested maps and how it's computed. I have a 100mb WAN connectin going to 19 branches. I have a class-map that identifies traffic to the individual branch and within that class, a policy-map is applied to prioritize voice over video etc.
 
Here's the QoS setup:
 
class-map Branch1-Policy
match access-group branch-1-acl
*
*

[code]....

I was adding the Video-Conf class to both Traffic-6calls and Traffic-10calls when I got the above error.  How would that percentage be calculated? I know by default i can only reserve up to 75% of interface bandwidth. The platform is 3945E running 15.1(3)

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved