I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 RepliesI need configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP and HTTPS) between these two interfaces without using NAT.The older IOS is causing me some problems. I don't have an outside interface configured for Internet access,but trying to connect via IP address does't work either. I may be able to configure a second DNS server for the 192.168.12.X network for testing purposes if needed. I even tried to set the default route to the Interface of the production ASA's inside interface (3.1), but that did not work either.
View 6 Replies View RelatedI am migrating my PIX configuration to ASA 8.4(2) with my old nat configuration.I don't want the traffic match ACL inside_outbound_nat_acl from inside interface with NAT [code]
when I configured "any" in "nat (inside,any)", I cannot type the "route-lookup" command but when I change like "nat (inside,outside)" then I can type the "route-lookup" command.so what's mean of "any" in this command?
This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
We have a pair of ASA5520 firewalls setup in a very inefficient fashion, and I wish to convert them to an active/passive cluster. Trouble is, there are a number of configuration option I will need to re-implement (VPN tunnels, remote users etc), and trying to capture the configuation with a simple "show running-config" or "show running-config all" or even "show startup-config" doesn't get me things like the pre-shared-key from the VPN configurations - and I don't know them all, so I can't simply re-enter them.Is there any way to get a dump of the running (or startup) config which shows the hidden settings like pre-shared keys and OSPF message digest keys?
View 5 Replies View RelatedWe received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances. Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues. The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration. I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one. Namely, I am using two specific sources of info for connections.
View 20 Replies View RelatedI am forced to upgrade my ASA 5520 software from 7.1 - 8.2 or higher, as I am not familiar with ASA I need expert opinions.I have following concerns regarding the upgrade.
1-Do I need to worry about the software licensing when I download 8.2
2-I read about the few difference in commands (ACL and NAT) in 8.2 what exactly I have to do here should I change the configured NAT and ACL with real IP in the existing configuration after the upgrade ?
migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;
[code]....
One of my clients has an older 3745 running IOS 12.3 and we are looking at replacing it with a new 3945 that runs IOS 15.0. This router is also configured with CME. Is it possible to migrate the current 12.3 config to load on the new 15.0 IOS? This will be my first encounter with 15.0 so I don't know what I am up against at this time. I am just hoping I don't have to retype all the ephone config, dial-peers, etc
View 2 Replies View RelatedI'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies View RelatedOur firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
I have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies View RelatedI just added a PIX515E to my lab (since this is a lab, if I need to change IP address, that is not a problem)....I thought I configured it right, but I am not able to ping any of my other routers/PCs.I have EIGRP on the other three routers, but not sure if I configured it right on the PIX.The diagram below shows my current network topology....(right now the PIX is connected vai Ethernet 1 to the switch, not the router itself) [code]
View 13 Replies View RelatedI just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
We are planning to upgrade the PIX515e (128 MB, 16 MB flash) adaptive software from 7.2(4) to 8.0.3(ED). In our environment the two PIXes are working in active-standby mode and experiencing high memory utilization.
1) What are the bug fixes(like memory leak fix) and new configuration options in the 8.0.3(ED)?
2) Is there any issues to upgrade 7.2 to 8.0.3(ED)?
3) Is the upgrade to new version software fix the memory utilization issue?
why the ethernet 3,4,5 is not licensed here ?
View 3 Replies View RelatedI am currently migrating a netscreen firewall to a asa 5515 version 8.6 The issue is setting up the management connectivity.
basically the management IP of the cisco asa is not advertised. But, we want to route a management IP through the management interface to interface Gi0/2.
so IP of management interface is say - 216.10.100.10. and the IP of the inside interface is say - 198.1.1.10/24 on our router we have a static route sending 198.1.1.0/24 to next hop of 216.10.100.10 (management interface of cisco asa).
On the Cisco ASA can I send the traffic to the inside interface and manage the firewall via ssh that way?
i wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies View RelatedWe have two PIX515E ( 6.3), one is Primary( Active) and second one is Standby. after configuration of Secondary Firewall as Standby. getting problem.
1. Configuration part everything is fine
2.we have done failover text also .
Aster Some time , we are not able see Standby Firewall its going down .
Quick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies View RelatedI have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.
It has two gateway(public IP). Configuration in MH2001 is pretty simple. and i have completed it.I have also completed configuration in PIX using ASDM. But the VPN is not up till now.
[code]...
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
[Code].....
The infrastructure has PIX515E as the Firewall and few Web Servers and Database Servers inside. Is it possible to retreieve information regarding the bandwidth available at the outside interface of PIX (Internet link utilization ) utilized by each of the nodes seperately? I could use SNMP to get the overall data transfer at the Outside interface of PIX but isit possible to get utilization details of individual nodes ? Is Netflow an option ?
View 10 Replies View Relatedi just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies View RelatedI currently have the following set up (excuse my quick drawing):
--------------Vendors VPN Router----
| ------Cisco 3000 VPN------ |
| | | |
Private Network-------ASA5510---------Pub Switch------Cisco Router 2x T1
I've been tasked with migrating to the new ISP, which provides us with Cisco ME-3400E switch and /26 public subnet. I currently have 15 static NATs and 14 L-2-L VPN tunnels configured in ASA. Is there a way to configure additional Outside int on ASA and use it to migrate the existing VPN tunnels and static NATs? I'm trying to avoid downtime and hope to do it step by step. I'm thinking about adding additional Public switch, so I can also migrate vendor's router and VPN concentrator, which need to be in parallel to ASA. Assuming that this is possible I'd would like to do the following:
1.Configure and connect additional Outside Interface on ASA - public IP address and ACLs
2.Connect it to additional "Public switch", which would be configured with public IP address and connected to new ISP's Cisco ME-3400E.
3.Migrate my VPN tunnels and static NATs.
4.Migrate vendors equipment/VPN concentrator
5.Update my global NAT pool
6.Shut down old ISP
I have ASA 5520 using ios 8.2(2)
I received a new ASA 5550 and want to transfert my config from 5520 to 5550
I have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
*** Device Details for ASA_5520_VOZ_01 *** Protocol ==> Unknown / Not Applicable Selected Protocols with order ==> Telnet,TFTP,SSH Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration. CM00 Polling not supported on
[Code].....
i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies View RelatedI'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies View RelatedI want to put the asa5520 to the factory default please let me know how to do that. how to remove the configuration file from it.
View 5 Replies View RelatedI am going to migrate an ASA5520 with another one having VPN configuration+certificates etc. I am a bit concern about the certificates. Shall I need a new certificate because of new IP addresses on the new ASA ? Should I configure the same IP in order to avoid this. There are many VPN clients with public keys that also need to change. Is there any way for minimal changes for migration ?
View 4 Replies View RelatedWith regarding to the firewall ASA5520, i'm using it in my network, all the confiuration are properly configured and working but with the use of proxy address in internet explorer(e.:206.53.155.129/3128) all the blocked contents as easily accessible simply it bypass all the network through firewall.so will u guide me to block the proxy servers.
View 1 Replies View Related