Cisco :: RME 4.2 Can't Get Configuration File From ASA5520
Aug 10, 2010
I have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
*** Device Details for ASA_5520_VOZ_01 *** Protocol ==> Unknown / Not Applicable Selected Protocols with order ==> Telnet,TFTP,SSH Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration. CM00 Polling not supported on
[Code].....
View 2 Replies
ADVERTISEMENT
Jul 15, 2007
I want to put the asa5520 to the factory default please let me know how to do that. how to remove the configuration file from it.
View 5 Replies
View Related
May 21, 2012
This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
View 4 Replies
View Related
Aug 21, 2012
i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies
View Related
Oct 9, 2011
We have a pair of ASA5520 firewalls setup in a very inefficient fashion, and I wish to convert them to an active/passive cluster. Trouble is, there are a number of configuration option I will need to re-implement (VPN tunnels, remote users etc), and trying to capture the configuation with a simple "show running-config" or "show running-config all" or even "show startup-config" doesn't get me things like the pre-shared-key from the VPN configurations - and I don't know them all, so I can't simply re-enter them.Is there any way to get a dump of the running (or startup) config which shows the hidden settings like pre-shared keys and OSPF message digest keys?
View 5 Replies
View Related
Apr 1, 2013
I am going to migrate an ASA5520 with another one having VPN configuration+certificates etc. I am a bit concern about the certificates. Shall I need a new certificate because of new IP addresses on the new ASA ? Should I configure the same IP in order to avoid this. There are many VPN clients with public keys that also need to change. Is there any way for minimal changes for migration ?
View 4 Replies
View Related
Dec 15, 2011
We received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances. Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues. The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration. I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one. Namely, I am using two specific sources of info for connections.
View 20 Replies
View Related
Mar 7, 2011
I am forced to upgrade my ASA 5520 software from 7.1 - 8.2 or higher, as I am not familiar with ASA I need expert opinions.I have following concerns regarding the upgrade.
1-Do I need to worry about the software licensing when I download 8.2
2-I read about the few difference in commands (ACL and NAT) in 8.2 what exactly I have to do here should I change the configured NAT and ACL with real IP in the existing configuration after the upgrade ?
View 5 Replies
View Related
Jul 18, 2011
I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies
View Related
Jan 3, 2013
is there a way to pull the config file from this? I tried looking through console mode, but was not able to find an option for it. Or is it just not possible?
View 1 Replies
View Related
Jul 22, 2006
If already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?
View 2 Replies
View Related
Feb 27, 2013
Currently, the backup config is not human readable...any way to convert this?
View 1 Replies
View Related
Aug 28, 2012
At home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
My Network is has follow :
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the swich look for :
tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?
View 4 Replies
View Related
Jul 6, 2012
How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies
View Related
Mar 15, 2011
What is the name or path for the file stored on your hard drive for the configuration settings?
View 7 Replies
View Related
Nov 10, 2011
Is it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies
View Related
Feb 25, 2013
I'm trying to save a configuration file on my 2960-48PST to a FTP server.
Unfortunately it doesn't work. What different steps I should follow ?
The software version is 12.2(50)SE5.
View 2 Replies
View Related
Dec 11, 2012
We have CISCO2811 model with VWIC2-2MFT-T1/E1 module working good over the E1 line. Since it's getting hard to find new model of CISCO2811 we decided to connect new branches with CISCO2911/K9 model (according to migration doc)
My question is can we use 2811's old config file with the 2911 model directly?
View 1 Replies
View Related
Aug 7, 2008
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies
View Related
Mar 20, 2012
I'm only able to restore my settings from a backup taken in July 2011. Any backups that I take, say today for example, won't restore. Any attempts to restore them is returned with "The restored configuration file has been uploaded in failure." I haven't changed my router. The firmware remains the same. I'm using Firefox, though I believe I've always used Firefox to interface with the router.
View 1 Replies
View Related
Mar 31, 2011
I've owned the Rev A DIR-655 for years and have loved it, but recently it started acting up. I have a complicated setup saved as a gateway settings file (.gws). I decided to purchase a new DIR-655 for the ease of importing my settings without having to manually setup again, however, much to my dismay, the new file format for the configuration settings on the Rev B is not .gws but rather .bin. The .gws file will not import. I tried changing the file extension to .bin with hopes it might import but no luck. I also found the utility which decrypts the .gws file into .xml and used those values to manually re-enter the settings into the Rev B router, but my port forwarding is not working the same. I was wondering if there is any utility to convert the .gws file to the .bin file in order to import into the Rev B router, or if not, can I still purchase the Rev A model somewhere. The online shops I've checked do not list the hardware version.
View 7 Replies
View Related
May 7, 2012
i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies
View Related
Jul 18, 2010
I'm trying to configure the NAC Profiler with a 3310 CAS Collector. In the "Edit Collector" menú, it shows all the modules as "Running", except for the NetWatch module which shows a state "Invalid configuration file (missingInternalAddress)".
I configured the eth3 interface of the CAS as a monitor interface in the Profiler (see attached image), and I tested that the SPANed traffic actually reaches that interface from the access switch. I'm using software version 3.1.0_24 in both the Profiler and the Collector.
View 2 Replies
View Related
Nov 4, 2012
I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?
View 1 Replies
View Related
Jan 25, 2012
I am trying to configure this router to obtain an IPv6 address from my ISP who offers a dual stack IPv4/IPv6 DHCPv6 Prefix Delegation service.
I did a WAN packet capture to see the type of DHCPv6 packets the router sends to the ISP in order to obtain an IPv6 address and I saw that the router is sending DHCPv6 solicitation packets of type IA_NA i.e. for Identity Association for Non-temporary Address. However, most ISPs that offer a dual stack IP4/IPv6 service, they use DHCPv6 Prefix Delegation in which case the router is expected to send DHCPv6 solicitation packets of type IA_PD i.e. for Identity Association for Prefix Delegation.
I then downloaded its configuration file and saw the following:
dhcpv6c = {}
dhcpv6c[1] = {}
dhcpv6c[1]["renewTime"] = "3600"
[Code].....
So, the option for the DHCPv6 client to perform a prefixDelegation request is disabled. Does that mean that if I set this flag to "1" it is going to work? Well, I edited the configuration file and changed this flag but the router refuses to load it! It complains about the file being changed. How does it know that? Is it computing some type of checksum? How can I manually edit this flag and update the router's configuration?
View 2 Replies
View Related
May 31, 2011
Our firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
View 1 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Jul 26, 2011
I am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies
View Related
Apr 23, 2012
I have configured SSL-clientless vpn on asa5520(8.2-asdm-6.4)It is working.Only problem is how to add pcs to the vpn.That mean like someone need to access pcs via vpn.Servers with url can add without any problem.is there anyway to add pc/servers with ip addresses?
View 2 Replies
View Related
May 16, 2013
we are trying to configure the vpn with our provider we are on Asa and the use Checkpoint , vpn seem to be established on phase 1 and phase 2 too.bur when i send ping packets seem to los on tunnel and other side do not see them.Asa is after a onother firewall and outside interface of this asa is nated on this perimeter firewall.
View 5 Replies
View Related
Oct 10, 2011
I'm trying to use a 5520 to test something but the bandwidth seems pretty low for the product I'm testing over it. Can anyone tell me if there is a bandwidth limitation by default? I'm seeing 1.5mb/s average with spikes to 6mb/s or so. On the ASA5550 I was seeing usage up to 80mb/s.
View 5 Replies
View Related
Feb 17, 2010
I'm trying to setup the SSL VPN portal:When I connect via HTTPS to the ASA5520 outside interface I get the login prompt and after successfully login it takes me directly to the Anyconnect client download (starts Anyconnect immediately) even though in the group policy is configured to not prompt the use to chose the post login and the post login is ste to go to Clientless SSL VPN Portal?
View 7 Replies
View Related
Feb 4, 2009
We have a several SonicWall TZ 190 establishing VPN tunnels with a ASA5520. Pericodically random VPN tunnels will drop and can not re-establish a connection. In order to re-establish the dropped VPN tunnel, our firewall folks manually drop all VPN tunnels connected to the ASA (they use to physically power cycle the ASA). They claim this is the only way to resolve the problem and since the SonicWall Life Time seconds for Phase 1 and 2 are set to 28800, they reset the tunnels every 8 hours. Additionally, they claim that SonicWall IPSEC is different that Cisco IPSEC which is the main problem. Hence they are requesting a SONICWAll VPN concentrator..
View 4 Replies
View Related
