i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies
I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?
View 1 Replies View RelatedIf already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?
View 2 Replies View RelatedI am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View RelatedBefore I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3. I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.
I'm busy on configuring the backup of the configuration from Nexus switches 5K and 7K.I have installed COPSSH on my windows server and try to confiugre the sftp credentials. [code] I have tested from the CLI from the switch and i have the issue but if i use the default vrf 'default' it works fine.How can i change the command sent by DCNM to the Nexus in order to specify vrf default and not vrf management ?
View 1 Replies View RelatedLet's suppose I'm connected to a network whose admin asked in a friendly way not to download anything but certain things he specified.He never came to my machine or setup any kind of client to it. The question now is, is there any chance he knows what I download???Does he know the name and the extension of the file I download if I use Utorrent and magnet links?
View 2 Replies View RelatedFindout what is the Reason for does not Opening a bin Extension File?
View 1 Replies View RelatedI am relatively new the configuring network switches. Could someone point me in right direction to configure SG300-28 as a DHCP server?
From the people I talked based on device specs it should be able to act as dhcp server. However, if we cannot, can it be configured so that clients get DHCP information from Firewall to which L3 switch is connected.
Previously srw2008 switches are used, now Cisco sg300-10 models was obtained. It does not work with ctrl-Z command to enter the local Config (lcli). What is the correct command?
View 2 Replies View RelatedI have several SG300-10 and SF302-08P switches running with L2-mode, and after I upgraded their firmware to 1.1.2.0, they began to record the following logs every one hour.
- Severity: Warning
- Description: %COPY-W-TRAP: The mirror-config file is illegal due to failure of previous copy operation/s to mirror-config.Also I found that I didn't see the Mirror Configuration file on the Configuration File Table in the Configuration Files Properties page.
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
About to apply a patch for the first time on the ACS 5.3 tonight. Ihave tftp'd it onto a directory i have created on the server. However my support hints i may havre to rename the file ? copy the latest patch file you got from Cisco – you may need to rename as gpg) Current filename is 5-3-0-40-7.tar.tar
So would i need to rename this as 5-3-0-40-7.tar.gpz . If so i will rename it on my pc and redownload it on tftp
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedI have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedJust purchased a SG300-52 and am trying to upgrade the firmware to 1.1.2 but cannot get the Upgrade/Backup Firmware Language page to load in the web browser interface. I have tried IE 8 and 9, Firefox 3.16 and 10.02, and Chrome from Windows 7 and XP Pro systems also tried FF and Chrome from Ubuntu system. The page just never loads - doesn't show anything.The same is true of the Download/Backup/Configuration/Log page. The other links under Administration > File Management seem to work fine.
View 1 Replies View RelatedI had ACS 5.2 ( Evalution License ) setup installed on VMware with patch 11 when I try to restore earlier backup of ACS gives me error "Cannot find acsbackup_instance.log in the backup file"
I am using Filezilla FTP sever for backup transfer.
I have a Nas4Free (FreeBSD) server on location A and another Nas4Free server on location B.
I need to regulary access to location B's some folder from Windows machine at location A. What is the best scenario for this?
I think to rsync those folders/files every night to location A, but then I think what if in the future there are many other locations (C, D, E, F) that need to be rsynced to location A, that will make location A need a very large harddisk space that maybe not available in the market or limit
by the hardware/BIOS support.
If the hostnames are the same - can I restore the backup file from a wcs 5.2.148.0 instance on a different wcs instance running wcs 6.0.196.0?
View 1 Replies View RelatedIs there a way to view the contents of the .exp file generated from exporting the configuration from RV082? I've got a couple of RV082 that have the same rules, but want to compare the configuration.
View 2 Replies View RelatedHow can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View RelatedWhenever I tried to do backup of CiscoWorks from GUI, I am receiving a error message"Backup failed. ERROR(292): C:PROGRA~1CSCOpx/backup.LOCK file exists, look into the log file C:/PROGRA~1/XCSCOpx/log/dbbackup.log for more details". backup.LOCK file size is 0KB.I am using LMS 3.2; RME 4.3.0;CM 5.2.0
View 1 Replies View RelatedI need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies View RelatedI'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedI have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View RelatedWe have ASA 5540 with 8.2 SW. We are trying to download a file (3 MB pdf) from https session which fails if done behind the firewall. In case, the client bypasses firewall, the file gets downloaded as usuall. Interesting thing here to note is that when client is behind the firewall, its takes a long time to download the file and the file size always 312 Bytes, of course its a corrupt file.
View 3 Replies View Related
