Cisco AAA/Identity/Nac :: Applying Patch To ACS5.3 - Change File Extension?
Nov 11, 2012
About to apply a patch for the first time on the ACS 5.3 tonight. Ihave tftp'd it onto a directory i have created on the server. However my support hints i may havre to rename the file ? copy the latest patch file you got from Cisco – you may need to rename as gpg) Current filename is 5-3-0-40-7.tar.tar
So would i need to rename this as 5-3-0-40-7.tar.gpz . If so i will rename it on my pc and redownload it on tftp
View 3 Replies
ADVERTISEMENT
Jun 3, 2012
I have an issue with applying a patch to an ACS 1121 appliance running version 5.2.0.26. I have 5 units that needed updating and the first one is the unit with the problem. The subsequent ones updated with no issues.
When I do a show version the 5.2.0.26.10 does not show. When I try to do a reinstall I get back patch all ready exists. When I try to do an uninstall I get back patch does not exist.
Is there a command can wipe out patch 10, so I can start over? The CLI factory-reset only wipes the web configuration not the running-config or IOS.
View 7 Replies
View Related
Nov 11, 2012
Let's suppose I'm connected to a network whose admin asked in a friendly way not to download anything but certain things he specified.He never came to my machine or setup any kind of client to it. The question now is, is there any chance he knows what I download???Does he know the name and the extension of the file I download if I use Utorrent and magnet links?
View 2 Replies
View Related
May 6, 2011
Findout what is the Reason for does not Opening a bin Extension File?
View 1 Replies
View Related
Aug 28, 2012
I have an ACS 5.3 cluster, that is configured to use AD. There are a few wireless devices, and monitoring tools that do not have AD accounts. I would like to configure ACS to first check AD for the user authentication, and if that fails to roll over to the local (Internal Users) identity source where I can define these user accounts.
It seems that when the authentication hits the initial Identity Policy rule, it never moves onto the next one if the first fails.
Attached are screen shots that show how i'm configured for the test, i have a local user defined and I'm trying to log into the firewalls.
- Identity Definition : Screen shot of the main ACS definition for the rule i'm testing that's not working
- Identity Rule 1 : The configuration of rule 1 that if it fails i need it to move onto rule 2.
- Log Output : Screen shot for one of the failed attempts from the ACS View Log server.
Reason I need to configure it this way is:
- Wireless users authenticate to wireless using AD user accounts. Some hand held scanners do not support that and will need to authenticate using the MAC address.
- Authentication to Network devices for managment uses AD accounts. We have some monitoring tools that do not have AD accounts, and will need to be able to log into Network devices to issue some commands (Examples: Cisco Prime LMS and NCS, Infoblox NetMRI).
View 4 Replies
View Related
May 7, 2012
i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies
View Related
Jul 30, 2010
I managed to connect acs5.1 to the AD , user's will be able to get authenticated against the AD when the state is shown "CONNECTED'. This will work ok for a day or so and goes into a 'DISCONNECTED' state , users will no more be able to authenticate . Is this a known error , or is this an error from the microsoft ws2k3 server side ?
View 3 Replies
View Related
Jan 26, 2013
I know ACS 5 lacks the IP Pools of earlier ACS versions. I'm looking at a 4 to 5 migration and was thinking of just configuring the IP Pools on the router ("ip pool local" etc) and sending back a RADIUS Cisco Attribute pair with the name of the pool. (Seemed like a neat fix, needs no extra kit, etc.)
I could have sworn that attribute pair existed... but I can't find it in ACS5! What's it's name?! Where is it!? Or have I gone mad!? (And, if I have gone mad, how would you go about fixing it?)
View 2 Replies
View Related
Jun 10, 2013
I am trying to configure Fortigate firewall for device authentication through TACACS+ using Cisco ACS 5.2.
I was wondering if any one had an experience to worked on this scenario. I am looking for authorization command attibute to grant admin access.
View 1 Replies
View Related
Nov 29, 2011
I want to export the ACS local user's records.Then import to other ACS5.3 server.But the export file not the user's password record.I cannot import it well....
View 1 Replies
View Related
May 17, 2011
we are moving network devices (200+) authentication/authorization/accounting to new ACS5.2, is there any easy way to copy/sync all those AAA clients configuration to another ACS5.2 server? I don't need other configuration to be synced/copied to another ACS5.2 server
View 8 Replies
View Related
Aug 18, 2010
I'm trying to dynamically assign IP address for VPN users from AD (without IAS service). I know that there is a restriction that "Dial-in users are not supported by AD in ACS (note in "acsuserguide51") but Im not exacly sure what can and can't do with it. In "Authorization Profiles" in RADIUS Attributes tab I try to mannually add specific Attribute (Framed-IP-Address).
I have no problem (everything works just fine) with static address assignment in a way as below:
AD is already integrated with ACS and I've managed to download Directory attributes especially msRADIUSFramedIPAddress
When I change "Attribute Value" from static to dynamic type I see the option to select AD (but "Select" which should list all available attributes is empty)
I know that I can do it directly (ASA <-> AD attribute mapping) but I want ACS to do it
View 5 Replies
View Related
Oct 13, 2011
We have customer with implementation ACS5.2 in Windows environment. Now they want to implement IP phones in the network.
View 0 Replies
View Related
Jul 9, 2012
I am trying to secure changes to switches using ACS 5.3 and allowing our technicians to only change the vlan for user ports on the switches. How can I use regular expressions to filter out the 1/1/# ports so that those ports cannot be accessed in config mode? If I allow the following, it allows access to all interfaces with 'gi' in them.
View 1 Replies
View Related
May 9, 2011
I need to patch our ACS server to 4.2.0.124.17 from 4.2.0.124.6. My question is, do I need to apply the same patch to our remote agents? Cisco's documentation only states that both the ACS and the Remote Agents need to be 4.2.0.
View 1 Replies
View Related
Mar 2, 2011
properly patching and/or cleaning the ACS version listed in the title.
First off - what does the Cleaning utility do?
Second - I have obtained the two following files:
ACS-4.2.0.124.17-SW
ACS-4.2.0.124.16-Clean
Can these both be used to correct a problem we have with our current installation?
View 2 Replies
View Related
Mar 3, 2011
I have everything working on a new 5.2 ACS but:I can only make a command set that permits things and denies all.I thought with the check box. Permit any command that is not in the table below" one could allow all and specifically deny commands.and that would allow the user to do all commands except for conf and set. But it doesn't seem to adminstratively block it, it allows them to still "conf" for instance.
Then it works as expected, it allows the commands that are permitted and denying all unspecified commands.I know I am in the right command set because the changes I make are reflected immediately.Can someone test the "Permit any command that is not in the table below' and tell me if it works? I can make it work with the unchecked box, sure, but it would be nice to get it to work.
View 3 Replies
View Related
Jun 11, 2012
I'm having trouble getting things working on a pair of ASA5510's using Cisco Secure ACS v5.1. We were previously using a much older version of ACS to these (and a lot of other) devices which worked OK for remote access for read/write use. Am in the process of migrating to the new ACS software and have got it working OK to everything (many Cisco switches and other IOS devices) except these ASA5510s.
I can get TACACS authenticating fine and am able to log on and go into enable mode. Any subsequent commands are then met with 'command authorization failure', including 'show run', 'conf t' and even 'exit'!
My ASA5510 config has not changed, other than to define the new AAA server, which leads me to think its something to do with how I have the ACS user profile set up. I have configured the ACS5.1 device administration Shell Profile to have the maximum privilege level (15) and the command set I'm using has the box checked 'permit any command that is not in the table below'.
View 7 Replies
View Related
Oct 3, 2011
We are trying to make a restore from the backup done on ACS version 5.1 to a new appliance running ACS5.2 Before doing it I found this note in Cisco ACS user guide:
Note: You cannot back up data from an earlier version of ACS and restore it to a later version. Backup and restore must be performed on the same version of ACS. If you need the data on a different version of the ACS, you can perform an upgrade after you restore the data. Refer to the Installation and Setup Guide for Cisco Secure Access Control System 5.1 for more information on upgrading ACS to later versions.
How should I understand it? This note has conflicting statements. We can't restore to a later version but if you need data on a different version of ACS you can perform an upgrade AFTER YOU RESTORE the data. Doesn't it mean that the restore will still work? How would I do the upgrade to version 5.2 or even version 5.3 that was announced to be released very soon? I didn't find anything on the software upgrade in ACS5.1 guide.
View 4 Replies
View Related
May 24, 2012
I am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies
View Related
Aug 27, 2012
I configured an ip pool on VPN 3000 concetnrator. i wanted to an attribute to use on the nework access profile on the acs 5.3. i was advised to use pool name. However, we don't have pool name attribute on VPN concentrator. only, IP range and subnet mask. how do i refer an IP pool on VPN concentrator in ACS5.3? is there another attribute I can use on ACS5.3 to invoke a pool on CVPN3000, like ip range...?
View 2 Replies
View Related
Aug 8, 2011
My company requires each user dial-in must be a fixed IP; The old acs4 can,but I cannot find the same configration item in the ACS5.2
View 2 Replies
View Related
Nov 25, 2012
I had a problem about authentication use AD group member. Below webiside is the way I config on ACS.
[URL]
I'm using ACS 5.1.0.44 and this version has a bug , ACS cannot read AD group. I have to add it manually . After I change the access policy from Internal user to AD1. I can use anyone AD ID to pass authenticaiton. I finished all config from the website had same result.
I checked the access polices -- default device admin -- authorization , the new rules I created had no hit count. How can I make sure that I make a right config ?
View 2 Replies
View Related
Aug 2, 2011
We plan to use machine certificates on our notebooks with Windows Vista. Our authenticating server is Cisco ACS 5.1. To access the wireless network we want to use the machine certificate of the notebook and a verification of the corresponding computer account in the Active Directory. What authentication method is the best to check the machine certificate and if in the Active Directory exist the enabled corresponding computer account ? How to configure the ACS and the notebook to use it like described ?
View 1 Replies
View Related
Aug 14, 2012
I am using Cisco ACS5.3 to authenticate users (using radius) for a cisco ASA firewall for both WebVPN and IPSEC client connections. I have been able to do this successfully. However I need to be able to deply Cisco vendor specific attributes (VSA) for both IPSEC and WebVPN sessions using authorisation profiles. Ideally I don't want to have to combine the attributes required for both services in the same authorisation profile, as I will have to produce alot of different profiles for the different combinations.
The only way I can see that you could possibilly do this is by having service selection rules that can differentiate between WebVPN and IPSEC Radius authentication requests. I have experimented inbound VSA's without success. Is this possible?
View 1 Replies
View Related
Jan 16, 2012
Is it possible to create on ACS5 rule which will:
1. Try to authenticate user in external database1 (radius)
2. When external database1 returns FAIL (because of bad password) ACS5 should try to authenticate user in another external database2 (radius)
View 5 Replies
View Related
Mar 22, 2012
what's the best way to apply a patch in ACS 5.2 distributed configuration ?
View 1 Replies
View Related
Aug 2, 2012
I installed ise-1.1.1.268.i386.iso on a scratch to the new NAC 3315. As i check cisco download mentioned it need to patch following files :ise-patchbundle-1.1.1.268-1-60802.i386.tar.gz,But once try to patch it show like attachment message, is it mean that i no need to do the patching?Or is there any instruction need to remove and reinstall for this files.
View 4 Replies
View Related
May 4, 2011
procedure to apply the 5-2-0-26-4.tar.gpg patch. I don't know how to get the patch file into the ACS server.The procedure in the "Read me" for the patch does not indicate anything about how to this:
1. open CLI console2. define new repository in which the 5-2-0-26-4.tar.gpg resides3. issue: 'acs patch install 5-2-0-26-4.tar.gpg repository YOUR_REPOSITORY'4. verify installation by getting the following version information via CLI by issuing:#show application version acs I don't know how to put the patch file from my local machine to the repository created in the GUI (if there is where the actual place to creat the repository).
View 3 Replies
View Related
Jun 12, 2012
I am trying to apply pach 5 to my ACS version 5.3 using FTP but i receive the following errors after issuing the show backup history command. When i use TFTP, i get a message saying that the file is too big, which i understand 164 MB.
after issuing the show repository "repository name", i get the following error.% Error reading directory on remote server.the patch is on one of my hard drives D, how do i specify on the ACS file path which drive to use?I can only place a url but without specifying which drive.
View 3 Replies
View Related
May 31, 2012
i'm using ACS 5.3.0.40.2 and its setup with an AD External Identity store for wireless PEAP MSCHAPv2. AD is configured with Alternate UPN suffixes so that for example: 22056 Subject not found in the applicable identity store(s). ##
I've checked the release notes for 5.3.0.40.5 and there are some changes/fixes for AD but nothing I can see to explain the behaviour above. I'm looking to upgrade to 5.3.0.40.5 soon but I really need the Alternate UPN suffixes to work.mydomain.com is the AD domain namean Alternate UPN suffix of another.com has been added to AD
A valid AD user can add either the @mydomain.com or the @another.com suffixes to their username and login successfully. This works fine with 5.3.0.40.2 but changes when I upgrade to 5.3.0.40.5 - users who use the @mydomain.com login ok but users using the Alternate UPN @another.com fail with the error: [code]
View 2 Replies
View Related
Jul 11, 2012
Why ACS5.3 requires 500GB datastore? what for? do we still need this when we use external database? am in the process of migrating from ACS4.2 to 5.3.
View 49 Replies
View Related
May 30, 2011
Our customer has the business needs to authenticate remote users against AD with empty password. I've seen ACS5.1 release note where mentioned about resolved issue: #CSCte72751 #ACS 5.1 drops authentication with empty password.
I tried to authenticate dial-in users through Tacacs and Radius against AD with empty password but without success. ACS points to wrong AD password. Is it possible to authneticate remote users with empty password?
View 3 Replies
View Related
