I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 RepliesI have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedHow can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedI have finally been able to reconfigure my BEFSR41 V3 Wired Router to properly support my small server environment. I would like to know if there is a way to make a complete Backup of the current configuration that should be restored to the router if it should become "reset" to factory defaults. This happened to me approximately a week ago, and it took several days, a couple of phone support calls, and quite a bit of"grief" and aggravation/frustration before I managed to get everything re-configured correctly. If it had been "Backed up" to a file, I could have restored it and been back up and serving websites in a few hours. Instead it took almost a complete week! Is it even possible to actually backup the router? Or... must I just print each screen to be sure I get it all?
View 4 Replies View RelatedI would like to the the RV042 for a one to one NAT, but I need it to NAT to an address that is not on it's local subnet. I have it routing properly to the address, but web interface only allows adding an IP on the local subnet. Is there a way around that?
View 1 Replies View RelatedWe have 3 Cisco RV042. These were purchased to permit VPN from two branch offices to our head office. VPN is required to permit the two branch offices to use Avaya IP phones to connect to our main head office switchboard.We also have users on Blackberry and Apple iPhones to collect their mail through OWA from our Exchange 2010 server.
I've noticed in one of your threads that the RV042 routers configured for VPN do not permit the use of HTTPS to connect to OWA and that seems to be the problem for us. Since installing the VPN our OWA access is not possible.
What can I do to resolve this problem and what router would you suggest that I could use at the head office to enable the two branches to connect VPN to head office? And if there is a suitable router, would I need to replace all three?
I use a BEFVP41 VPN router. I have changed several settings. How can I backup these settings and store these settings in a save place.
View 3 Replies View RelatedI have never setup a GW to GW VPN with a FIOS connection. I have done it with DSL and cable without any problems.
View 1 Replies View RelatedI'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
View 1 Replies View RelatedI am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies View Relatedmy office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 1.3.7.4BEFVP41 - ver. 1.02.00?
View 5 Replies View RelatedLAN L1, with IP addresses 192.168.10.x, for Company C1
LAN L2, with IP addresses 192.168.11.x, for Company C2
I have networks separated: different racks (but very closer fisically: a wire can be thrown), different gateways (to DSL), but both LAN's must connect with each other. I have acquired two RV042, one for each company to create VPN's (permitting telejob).
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
View 1 Replies View Relatedi am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
[code]....
My quickvpn setup has been working great for a few years but it stop working recently with the following error message in wget_request_error.txt: HTTP request sent, awaiting response... 501 Not Implemented 20:10:10 ERROR 501: Not Implemented.quickvpn hangs on the dreaded verifying network stage.Checked VPN router logs and also quickVPN client logs and confirmed the tunnel has been created successfully. However the ping was unsuccessful.I look through the forum and confirmed that my quickvpn user account and password only contains alphanumeric characters.
View 1 Replies View Relatedstatic route on RV042?
View 1 Replies View RelatedWe have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies View RelatedSmall office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
View 1 Replies View RelatedI have been running a email/web/ftp server on one server for 9 years. I have currently acquired a Barracuda spam 300. I cant get the emails to go thru the barracuda first. Here is how it is setup: my email and web come in thru one outside address..call it 166.5.5.5 I have a 1 to 1 nat for 166.5.5.5 to 10.0.0.2 (email/web/ftp server) ports 25 and 53 are forwarded to the 10.0.0.4 (barracuda) then out on 25 to my 10.0.0.2 no emails go thru as long as it is set this way I can nat the 166.5.5.5 to the barracuda first and emails go thru, but I lose my web and ftp will this router work for me? I was told that i needed to change mx records for email to 166.5.5.6 and then forward nat on that address to the barracuda. I dont really want to change mx records for 10-12 email domains.
View 1 Replies View RelatedI am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedDid anybody ever succeeded upgrading 1.3.12.19-tm to 4.0.0.07-tm version?
View 1 Replies View RelatedI have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies View RelatedHaving a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies View RelatedI've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....
Spent a lot of time trying to configure a time warner set up. Users are using 2 SMC 8014 and one RVO42 on the network. Cannot access the internet.
View 1 Replies View RelatedWe have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. how to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 1 Replies View RelatedWe have a RV042 with the lastes firmware v4.1.1.01-sp. We try to use Aastra SIP Phone 55i. Phone work perfectly with no router. But behind router call cut off after 5 minutes. Phone registration SIP periode are 30 second. Block WAN Request, and Multicast Passthrough firewall setting are desactivate.
View 1 Replies View RelatedI have a RV042:Firmware Version : v4.0.0.07-tm (Aug 19 2010 19:19:50)PID VID : RV042 V03 .Configured with a internal LAN address (10.0.17.0/24) and ISP PPPoE External address on WAN1.I´ve configured a VPN with a remote location (Fortigate 4) and after the VPN starts up the RV042 cannot ping any machine in their local network (using the diagnostic, all pings failed in 10.0.17.0/24) and no machines in that network can PING and access or manage the RV042
The only way to manage the RV042 after VPN starts UP is using a machine in the other side of the VPN (The Main office)If i force the VPN down, the connectivity begins to work, but as soon the VPN starts up again, the local/LAN connectivity loses again.
I am going to this page: [URL] but I can see nothing regarding firmware. The "Download software" link takes me to a page that has QVPN, TFTP utilities, etc, but no firmware.
View 4 Replies View RelatedWe have almost identical networks in two offices, with the only difference being, one uses an RV042 and the other an RV082.The setup is: two WAG54GS ADSL modems carry PPOA ADSL connections with static IPs to the two WAN ports of the RV0XX.The WAG54GS routers are configured to DMZ all incoming traffic to the relevant WAN IP of the RV0XXs. VPN pass-through is also set on them. The RV0XX port forwarding is set to forward a selection of traffic such as, PPTP, HTTP, HTTPS, RDP, POP3, SMTP and Remote Desk to the external adapter of an SBS 2003 server which processes all operations including ISA and Exchange.Mail for Exchange arrive through both ADSL connections for redundancy. VPN connection requests from remote users to the SBS come in through both ADSL connections.The office fitted with RV042 works fine and does all the following without problems.The office fitted with RV082 has issues. Remote VPN requests comming from ADSL to WAN port 1 of the RV082 connect successfully to the SBS2003 server, but the VPN requests coming from ADSL to WAN port 2 fail to connect! Similarly, incoming mail destined for Exchange don't get through if coming from ADSL of WAN port 2.I have updated the firmware on both RV042 and RV082, but the RV082 still has the above issues.
View 1 Replies View RelatedWe have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies View Related