Previously srw2008 switches are used, now Cisco sg300-10 models was obtained. It does not work with ctrl-Z command to enter the local Config (lcli). What is the correct command?
View 2 RepliesWhat does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies View RelatedI am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View RelatedBefore I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3. I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.
I am relatively new the configuring network switches. Could someone point me in right direction to configure SG300-28 as a DHCP server?
From the people I talked based on device specs it should be able to act as dhcp server. However, if we cannot, can it be configured so that clients get DHCP information from Firewall to which L3 switch is connected.
i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies View RelatedI have several SG300-10 and SF302-08P switches running with L2-mode, and after I upgraded their firmware to 1.1.2.0, they began to record the following logs every one hour.
- Severity: Warning
- Description: %COPY-W-TRAP: The mirror-config file is illegal due to failure of previous copy operation/s to mirror-config.Also I found that I didn't see the Mirror Configuration file on the Configuration File Table in the Configuration Files Properties page.
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedI have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedI'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedI have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View Relatedwe just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View Relatedshow cdp neighbors command shows two devices connected through the same local port?I have a Cisco 3560 that when I issue the "show cdp neighbors" command I get the following results: [code]
the question is why is this showing that Gig0/3 is being used twice to connect to two different devices. I have verified there is no hub connected to this port and in fact Switch3 is not connected to Switch1 at all yet it still shows up in the CDP table.
I have cleared the CDP table on every device at this location and still get the same results.
I am trying to configure Cisco SG300-52 switch for the first time and stuck without CLI configuration option. The configuration can be done using GUI, however, configuring using CLI would be more comfortable (as I am used to work with CLI of other Cisco switches)..
I was able to lo gin to switch using SSH, but the CLI appears in MENU format and was not able to find any way to go to CLI mode.
As per some blogs, in SG300 switches CLI mode can be accessed using Ctrl + Z in Menu, which did not work either in my case.
Switch is running with latest firmware version Sx300 Firmware Version 1.2.7.76.
try to configure QoS on a Cisco Small Business SG300 Switch. I followed the instruction on [URL] and configured one Port for tagging my Traffic from a Aastra IP Phone. Tagging works fine (i verified with wireshark).The problem is, that all traffic to a PC connected directly to the Aastra IP Phone is blocked. Is there a possibility to tag any other traffic to the port as a default?
View 1 Replies View RelatedI have an SG300, configured with several VLANs. I'm replacing a E3000 with the RV180, I've got it in the environment, but I can't seem to get to the internet from hosts on the SG300.
I have Port 4 on the RV180 connected to Port 20 on the SG300...Port 20 is in the native VLAN (VLAN1) and VLAN1 is configured as a trunk. I'm relatively new to networking so I'm not sure where to start troubleshooting. I have the default route on the switch and I have the static routes for the VLANs on the router, should I be using tagging someplace?
A client of ours has installed an SG300-24P switch and would like to setup a LAG between the SG300 and the 3560 switch we manage for them. They would like the LAG to also pass the voice and two data VLANs currently in use; 5, 10, and 100 respectively. I configured the two ports as an Etherchannel with trunking on the logical port, but no luck. I reconfigured as follows:
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
end
[code]....
I see no output when I do show lacp nei. At this point the client is looking to use for the configurations to use as he does not know how to setup the SG300 and it is a switch I have never dealt with. I have found some configurations that I believe would allow a single VLAN across, but nothing I believe will allow the LAG to pass all the VLAN's.
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies View RelatedOn my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?
View 2 Replies View RelatedIn the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?
View 6 Replies View RelatedWe purchased a SG300-52 last week to replace a 5yr old Dlink which has worked perfectly. 1 day after the SG300 went it it started crashing with this fatal error problem so I reverted the firmware back from 1.2.7.76 (latest) to 1.1.2.0 but I still get the problems. It crashes when I have it on my lan with users connected or if I just have the switch on my desk with just my laptop connected, so it cant be a load issue or a network topology issue. I already have a Cisco SGE2010 on my network without problems.
View 7 Replies View RelatedI have a question about ACL and binding. I have a SG300 28P and a couple of other linksys switches and Access points that are connected to it via trunks. The cisco SG300 28P is running in layer3 mode and i have created a couple of vlans and one of them is a guest vlan. Now to my question, i create an ACL and an ACE that vill funktion so that guest vlan only can connect to the internet and not the rest of the internal network. And then i must bound the ACL to an interface port or lag, what i can see it is not possible to bind it to an vlan? so if i have a port on some of the other switches that is member of the guest vlan, vill the ACL on the SG 300 stop guest vlan trafic to the internal network that is comming from some of the other switches?
View 1 Replies View RelatedI want to set up a vlan only for the wifi APs and wifi clients on my network. They can't access to any server, only internet acces. I already implement this configuration and its working, but now I want to allowed a couple of laptops to connect to servers in other vlan. what should I do? Should I do it using Mac address of laptops or IP?
View 9 Replies View RelatedYesterday I upgraded my SG300-10P to firmware 1.2.7.76. I was curious about the new SYN Protection feature, but it seems to do nothing on my installation.
The switch is running in Layer 2 mode. I have ACLs in place and DoS prevention is not enabled. I also tried clearing ACLs and enabling DoS prevention. As I understood the Admin Guide enabling DoS in the Security Suite Settings is not necessary for using the SYN Protection.
In my firewall I see about 300 pps with SYN flags only arriving. What "they" do is sending me SYN packest to port 80 from forged IPs, so that my system should send SYN-ACKs to the victim system. In this case it is the Arab Bank. They are down at the moment...I think that is called a spoofed SYN flood attack.
So I thougt the SYN Protection feature should exactly solve that problem but it does not and does not show any "Last Attack" entries.
If I put a SYN filter in place it works, even if I put SYN Rate Protection in place. But that is just a dirty workaround. My firewall blocks those SYN packets with a SNORT rule.