Cisco Switching/Routing :: SG300-52 - CLI Configuration Option
Dec 10, 2012
I am trying to configure Cisco SG300-52 switch for the first time and stuck without CLI configuration option. The configuration can be done using GUI, however, configuring using CLI would be more comfortable (as I am used to work with CLI of other Cisco switches)..
I was able to lo gin to switch using SSH, but the CLI appears in MENU format and was not able to find any way to go to CLI mode.
As per some blogs, in SG300 switches CLI mode can be accessed using Ctrl + Z in Menu, which did not work either in my case.
Switch is running with latest firmware version Sx300 Firmware Version 1.2.7.76.
View 2 Replies
ADVERTISEMENT
Jun 20, 2012
try to configure QoS on a Cisco Small Business SG300 Switch. I followed the instruction on [URL] and configured one Port for tagging my Traffic from a Aastra IP Phone. Tagging works fine (i verified with wireshark).The problem is, that all traffic to a PC connected directly to the Aastra IP Phone is blocked. Is there a possibility to tag any other traffic to the port as a default?
View 1 Replies
View Related
Jul 19, 2012
I have an SG300, configured with several VLANs. I'm replacing a E3000 with the RV180, I've got it in the environment, but I can't seem to get to the internet from hosts on the SG300.
I have Port 4 on the RV180 connected to Port 20 on the SG300...Port 20 is in the native VLAN (VLAN1) and VLAN1 is configured as a trunk. I'm relatively new to networking so I'm not sure where to start troubleshooting. I have the default route on the switch and I have the static routes for the VLANs on the router, should I be using tagging someplace?
View 3 Replies
View Related
Aug 27, 2012
A client of ours has installed an SG300-24P switch and would like to setup a LAG between the SG300 and the 3560 switch we manage for them. They would like the LAG to also pass the voice and two data VLANs currently in use; 5, 10, and 100 respectively. I configured the two ports as an Etherchannel with trunking on the logical port, but no luck. I reconfigured as follows:
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
end
[code]....
I see no output when I do show lacp nei. At this point the client is looking to use for the configurations to use as he does not know how to setup the SG300 and it is a switch I have never dealt with. I have found some configurations that I believe would allow a single VLAN across, but nothing I believe will allow the LAG to pass all the VLAN's.
View 7 Replies
View Related
Oct 4, 2012
We have an SG300 managed switch located in a small business of less than 10 PCs. There has been an ongoing issue with Internet speed. Is there any way that I can monitor the router for traffic so that I can see what might be causing the problem? I would like to focus on the WAN port and Internet activity particularly.
View 1 Replies
View Related
Jul 16, 2012
Im trying to find an affordable Cisco switch with similar capabilities and features as the WS-C3560X-48T-S (L2/L3 routing as in IP Base, dual power supply, etc.).
View 2 Replies
View Related
Nov 5, 2011
just got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?
I also noticed when I removed it the switches crash dump and rebooted?
View 12 Replies
View Related
Sep 19, 2012
I am updating the iOS for a 4948 the bootflash is empty so all i can get into is the rommon. There is no option for x-modem. How can I put the iOS onto this device? [code]
View 2 Replies
View Related
Dec 11, 2012
We have a Cat2960-S Series PoE+ currently running 12.2(55) SE5 ios with SW image C2960S-UNIVERSALK9-M.We want to upgrade the ios to the lastest version but found there are 2 version: 12.2(53) SE2 and 15.0(1) SE.Which is the best & suitable for upgrade?
View 3 Replies
View Related
Dec 12, 2012
I have a very simple setup containing 3 C2960S switches:switch 1: central switch, acting as router between VLAN 1 en VLAN 2switch 2+3: edge switches, connected via 1 link to central switch, both on VLAN 2,Clients connect to switch 2 and 3 using dhcp, switch 1 uses dhcp relay to forward requests from VLAN 2 to the dhcp server on VLAN 1. So far so good.Now I want switch 1 to add option 82 to the dhcp requests so the dhcp server can see whether the request came through switch 2 or switch 3. I tried turning on dhcp option 82 support on switch 1 by doing.
View 2 Replies
View Related
Oct 31, 2012
Why rpr is the only available redundancy mode option available to me. I'm running a 4507R+E with twin SUP7-E's.
Abbreviated show ver Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.03.01.SG RELEASE SOFTWARE (fc2)Technical Support: [URL]/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Sun 26-Aug-12 13:45 by prod_rel_team
ROM: 15.0(1r)SG2gp08401 uptime is 6 weeks, 6 days, 4 hours, 59 minutesUptime for this control processor is 6 weeks, 3 days, 2 hours, 21 minutesSystem returned to ROM by RPR SwitchoverSystem image file is "bootflash:/cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1.bin"Jawa Revision 7, Snowtrooper Revision 0x0.0x1C
[code]....
View 3 Replies
View Related
Oct 27, 2011
In RFC 951, the format of BOOTP packet was legislated, but the vendor information was not legislated in this document, so the authors of this document had described that :"If the 'vend' field is used, it is recommended that a 4 byte 'magic number' be the first item within 'vend'. This lets a server determine what kind of information it is seeing in this field. "
I think it meant that the format of vendor information wasn't fixed in RFC 951, and any vendor can legislate a new format of vendor information by itself. And the value in "magic cookie" can be set by any vendor.But in RFC 2131, the format of DHCP packet was legislated, and the "magic cooke" was fixed to values 99, 130, 83 and 99, I think it meant that the format of option information in DHCP packet was fixed absolutely and any vendor can't legislate a new format by itself.
Since the format of option information in DHCP packet was fixed absolutely, why the network device needs "magic cookie" to identify the mode in which the succeeding data is to be interpreted ? I think the magic cookie is not useful in DHCP packet because the format of option information is fixed. In other words, there is only one format of option information forever.
View 6 Replies
View Related
Nov 29, 2012
I ran into problem with design that was prepared for Catalyst 6500, but in the meantime infrastructure got upgraded to Nexus. I have two datacenters connected with 1Gbit line (point-point), both ends of this circuit are N7K. There are few segments (like LAN, DMZ, PUBLIC) in separate VRFs in each DC and intention was to carry over these segments between locations using VPNv4 exchange via BGP. Each location have its own AS number and IPv4 BGP session is running between them (for global routing table at the moment). I tried to add VPNv4 to that peering session, but got message it is not supported in NX-OS for eBGP. Tried to find some more info about such limitation, but failed.
Before I start explore other options like Option A (creating subinterfaces per VRF and running separate IPv4 BGP session in each).
View 2 Replies
View Related
Oct 30, 2012
we have 6500 series switches by default all port channel loadbalancing is src-dst-ip.Now we have a requirement to change LACP load balance method to src-dst-port.
1) If we change LACP loadbalance method whar are the effects we are going have on our core network and all the existing servers
View 3 Replies
View Related
Feb 6, 2012
We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
View 3 Replies
View Related
Jun 9, 2012
I am trying to configure a 4507 R chassis with Dual SUP but i cannot see teh switchpot mode trunk encapsulation dot1q?
I have typed:
interface GigabitEthernet5/1
description DOWNLINK toxxxxxx
switchport mode trunk
channel-group 11 mode on
!
I have have searched all other commands and sub-commands but could only find dot1q-tunnel which I beleive is for QINQ or some QoS featues and lot for L2 encapsulations?
the puzzling is:
XXX-Core4507#sh int gi5/1 trunk
Port Mode Encapsulation Status Native vlan
Gi5/1 off 802.1q notrnk-bndl 1
(Po11)
when I connect the dostribution switch a 3507 to this int gi 5/1, both interfaces do come up?
View 9 Replies
View Related
May 2, 2013
is it easy to remove the 3750x stacking? i'd like to test one of them on a sunday and keep the other one on production. it's just two stack of 3750x, is it hard and do i really need to remove the cables on the back?
basically i need to put a different config for my testing, i gues i need to remove the cables right? and put it back on the stack before monday.
View 2 Replies
View Related
Feb 5, 2012
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
View 11 Replies
View Related
Jun 12, 2013
I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies
View Related
Jun 19, 2011
i have Aztech DSL605EW wireless modem. I updated its firmware on some philipines Globle Broadband network's firmware. Now the problem is to open its configration I have to use 192.168.254.254 IP and the configuration settings are very limited and there is no option of updating firmware in it. I am stuck with it.
View 3 Replies
View Related
Dec 8, 2011
I am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.
View 1 Replies
View Related
Feb 28, 2012
I have three Cisco SG300-28 switches. I setup a test lab environment with a core (server) switch in Layer 3 mode and the rest are (clients) in Layer 2 mode. As I understand, these switches doesn't support VTP, only GVRP. And GVRP works the same with VTP. Whenever you create VLANs on the core or main switch, other switches will learn from the core switch and no VLAN creation for the client switches will be made. (Hope I got it right. I guess GVRP is more complicated than VTP). I want to use GVRP to create VLANs on the main switch so that I won't be doing it all over on the other switches. The following is my (so far) configuration through CLI only:I haven't use the web GUI. My SW version is 1.1.2.0.
1. I already enabled the GVRP globally.
2. I configured GE 12 & GE 24 as TRUNK ports for the core switch that connects both switches, I also configured GE 12 ports for both the client switches. All other ports are in ACCESS mode. (I am connected to GE 2 port)
3. I enabled GVRP on the TRUNK ports only for all switches.
4. I allowed all vlans on the TRUNK ports. (#switchport trunk allowed vlan add all)
5. All TRUNK ports registration mode is NORMAL and dynamic vlan creation is enabled on all trunk and access ports.
6. I created 3 VLANs without configuring its IP Addresses:
-vlan 2 = MGT
-vlan 3 = IT
-vlan 4 = MKTG
I don't know if I missed something on the configuration or the connection.
1. Is it necessary to enable all switches to layer 3 mode? Or depends on the network setup? Does this affect the GVRP?
2. Does switching ports to TRUNK mode means they are already 802.1q ports by default? Because I can't configure TRUNK ports to 802.1q (#switchport encapsulation dot1q) config like other switches. [code]
View 1 Replies
View Related
Jun 6, 2012
I just purchased an SG300-10 (negular, non-POE) and planning on using it with no special configuratinos initially. Longer term, will be using VLAN and QOS for VOIP.What I would like to know is if ports 9 & 10 can be used as standard copper cat5e ports, or are they only useful for special purposes? When I hookup my router/firewall to port 1 it all appears to work. If I hook it up to 9 or 10, the port lights do not come on and it doesn't work. I read that ports 9 & 10 don't have POE on the POE switch, but I assumed that all 10 ports would function with cat5e?
View 1 Replies
View Related
Apr 10, 2012
We are using the SG300 series switches, and have come across an issue where we need to block ARP broadcasts based on IP.
we have multiple computers, each with only one ethernet adapter, each adapter has two IPs configured, 10.10.10.x and 192.168.0.100.All machines have the same 192.168.0.100 address (Used for applications/hardware running locally to that machine and this IP cannot be changed).
When the machines are connected to the network, ARP is advertising BOTH the 10.10.10.x address and the 192.168.0.100 address.
As all machines have the same 192 address we receive IP conflict notifications on each machine.
How can the ARP broadcasts for the 192 address range be blocked?
View 1 Replies
View Related
Mar 13, 2012
I'm looking to configure the QOS for VOIP on my network.I have a switch SG300 and several no Cisco VOIP phone. What are the parameters to be taken to implement the QOS?
What is the procedure for installing the QOS? I need to create a VLAN for the data and one for VOIP?I read in the quick start guide that there is auto-QOS for VOIP?This can be done from the GUI? what are the options to put?
View 0 Replies
View Related
Feb 28, 2012
I have a new redundant network with two cores C1 and C2 and five access switches A1 to A5. They are all Cisco SG300 switches. I have noticed there are too many STP messages emanating from one host which has a MAC address which cannot be traced on the network. In the redundant network, I made C1 the root bridge by giving it a priority of 4096 and C2 has been given a priority of 8192 so that it is the secondary root bridge in the network. I have left all other STP settings to default on the rest of the switches in the network.
The problem is that one host is advertising a RST root bridge all the time. Now it has a mac address which is different from the mac address of the root bridge itself and i cannot trace this mac address on the network. Look at the snapshot of Wireshark output in the attach.The source MAC address which is the host advertising all the time is 1c:df:0f:34:db and the root bridge is 1c:df:0f:bb:34:c4.
Why would the root bridge be resetted all the time?I've also noticed that one port in a LAG configuration on one of the access switches is flapping up and down all the time.I tried to troubleshoot this problem. It is not the cable. It would be something else. What could cause this flapping of the port?Could it be related to STP?
On the other Core switch C2 I can see a LAG status switching between forwarding and blocking all the time. What could make the LAG status to flap from forwarding to blocking and back all the time like this?
View 3 Replies
View Related
Apr 3, 2013
I have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 Replies
View Related
Jan 31, 2012
it says that the cisco sg300-28 managed switch default system mode is Layer 2. but i want to change it to layer 3.
i can't get inside the "Console Interface Main Menu" where the switching from L2 to L3 will be done.
I have done the ff:
1. Upgraded firmware to 1.1.2.0 (latest)
2. Reset the switch to factory defaults.
3. The guide stated that in order to perform telnet to the switch, you need to enable it. So I logged in first in to the web GUI and enable telnet service.
4. I can now start telnet on the switch but I can't see the "Switch main menu".
All I can see are these lines from telnet:
User Name:cisco
Password:******
switchd5928c#
I just want to know how to get into the console interface main menu where these lines should appear so that i can change the system mode:
• System Configuration Menu
• Port Status
• Port Configuration
• System Mode
• Help
• Logout
View 3 Replies
View Related
Jun 1, 2012
I'm looking for feedback and constructive criticism on our network redesign project for our company.We are currently on a 192.168.1.x/24 and running out of addresses. We are looking to move to the following design and implement VLANs as well for segregation and security. We are probably going to use a few SG300s for switches. [code]
View 4 Replies
View Related
Jun 1, 2012
Can a Cisco SG300-10P switch power a Cisco SG200-08 switch over POE? Or an SG200-08P power an SG200-08 via POE? I have an area where I'd like to put a small switch, but would like to avoid having to have electrical power run to it. Or will the SG300 and SG200 POE switches only power endpoint devices such as cameras and IP phones?
View 4 Replies
View Related
Apr 20, 2012
I am having trouble with my Cisco SG300 switch big time. I have two servers with IP addresses 10.17.0.11 and 10.17.0.29 sitting on the same switch which is a Cisco SG300. I initiate a file transfer from 10.17.0.11 to 10.17.0.29. I could see lots of Dup Acks and retransmissions which means something is wrong in the connection. Further, I could see the session initiation a bit bizarre. I could see two SYN packets sent from 10.17.0.11 to 10.17.0.29 and also two SYN ACK packets returned by 10.17.0.29. The switch forms part of a network but since both the servers are sitting on the same switch I suppose the rest of the network doesn't come into play when one server talks to the other.
See also the number of Dup Acks and retransmissions. The two switch ports connecting the servers have speed and duplex set to auto negotiate, flow control is enabled. What could cause this sort of problem?Could it be any setting on the switch or the servers' NICs?Or could it be a bad switch that causes this?
View 4 Replies
View Related
Dec 12, 2012
I have an sg300-10 unit. I have recently swapped it into my LAN network to replace an aging switch that was exhibiting problems.
The SG300 is reporting near constant 100% cpu load with 11pps input. there are only 3-4 active ports on the switch at a given time. One of those ports does lead to my router and another switch with another half dozen devices.
By itself this doesn't concern me overly much, but I have found that the SG300 is occasionally freezing up for about 20 minutes then restarting. Syslog and SNMP traps don't appear to provide any hints as to what is going on.
I have tied my switch into my monitoring system (packettrap MSP, so if there is something I should be watching that I am not, that would be good to know). I am still troubleshooting getting all the monitoring functions working as well.
So, I have some questions there as well, which OID should I be monitoring for CPU utilization?
View 3 Replies
View Related
Apr 16, 2012
I am trying to setup VLAN's in the company I work for and I am almost there but missing the part when the internet works.I have an SG300 as a L3 Router IP 192.168.0.93.I have created VLAN20 and VLAN40 Assigned VLAN20 192.168.2.1 and VLAN40 192.168.4.1
The static routes have been created and a default router going to the Sonicwall firewall at 192.168.0.1.Port 24 is configured as Untagged VLAN1, Untagged VLAN20 and VLAN40 in trunk mode and going to the Sonicwall NSA 2400. [code]
Working to move all 192.168.0.x network off of VLAN1 and move it a management switch.I have DHCP helper on pointing to the DHCP server.Both VLAN's once the DHCP server is configured to Gateway 192.168.0.93 can get an IP from the correct subnet either 192.168.2.x or 192.168.4.x
All PC's are getting a GW IP of 192.168.2.1 pr 192.168.4.1.All test PC's on both VLAN's can ping each other and any server with the correct GW.When I try to ping google.com or open a web page and try google.com it times out.
View 3 Replies
View Related
