I have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 RepliesI'm looking to configure the QOS for VOIP on my network.I have a switch SG300 and several no Cisco VOIP phone. What are the parameters to be taken to implement the QOS?
What is the procedure for installing the QOS? I need to create a VLAN for the data and one for VOIP?I read in the quick start guide that there is auto-QOS for VOIP?This can be done from the GUI? what are the options to put?
One of my engineers issued a command to turn off port security on a number of ports using the range command. The command failed on the first attempt due to a tacacs auth failure which I suspect is due to a low tacacs timeout value. The engineer then reduced the number of ports in the range command and re-issued the config change after which the switch just crashed and rebooted.
The logging buffer on the switch displays the following:
000072: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: System previously crashed with the following message:
000073: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE3, RELEASE SOFTWARE (fc1)
000074: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Technical Support: [URL]
000075: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Copyright (c) 1986-2009 by Cisco Systems, Inc.
000076: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Compiled Wed 22-Jul-09 07:03 by prod_rel_team
000077: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED:
[Code]........
I have done some searching and this could be related to bug CSCsq71492. I have tried using the output interpreter but it is still down.
On a small Bording School we have the students living in several small houses, each equipped with an AP.Each Ap serve 4 Vlans.I want to restrict the switch for these AP, in a way to keep the students from removing the AP and connecting their own equipment.I tried using the secure port feature on the SG300, but that had the result of allowing the AP but denying all the users connected to the AP.The switch is a SG300-28P placed in L3 mode.
View 3 Replies View RelatedI have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedIn my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedI have some cisco 4500E with sup7l-e and I want config acces port(with non-cisco ip phone), that cos and dcsp mark does not change.
View 4 Replies View RelatedSome tips and trick on how to configure and sg300 for intervlan routing.
I already have the switch set up for layer 3 I already set up multiple vlans and each vlan has a ip interface setup with the desired subnet I see the local routes set up in the static routing page.
I cannot seem to get from one subnet/vlan (I am using one subnet for each VLAN) to the next.
I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedWe have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies View RelatedI need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.
View 1 Replies View RelatedTrying to configure the Cisco 4948e switch gigabit ethernet port with "switch port trunk encapsulation dot1q", but didn't get the option. Please find below the options got after "swith port trunk"............
SW(config-if)#switch port trunk ?
allowed Set allowed V LAN characteristics when interface is in trunking mode
native Set trunking native characteristics when interface is in trunking mode
pruning Set pruning V LAN characteristics when interface is in trunking mode
SW(config-if)#switch port trunk. Please find below the version of the SW............
SW#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-LANBASE-M), Versi
on 12.2(54)SG1, RELEASE SOFTWARE (fc1)
Technical Support: {URL}
ROM: 12.2(44r)SG11
Hobgoblin Revision 21, Fortooine Revision 1.22
[code]...
So, whether the command is not supporting on this Cisco switch ? But we have Cisco 4948 Cisco sw where that command is working fine.
I can´t configure speed in a giga port on WS-C3560-24PS-S switch(config-if)#speed ? no negotiate Do not negotiate speed
do you know if the port support speed 100??
because I need to connect with 2955C-12 switch in one port: 100BASE-FX (Multimode Fiber) uplinks, this port its only 100mbps?
and the switch C3750G-12S-E can I configure the ports on 100mbps?
I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies View RelatedI would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies View RelatedPossible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
View 2 Replies View Relatedhow to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
3750 Config:
interface Port-channel2
!
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100
[code]....
Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.
I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies View RelatedI have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
Site A Site B
3750X -A1 --------------------------------------( )--------------------------------------- 3750X -B1
( L-2-L )
3750X -A2 --------------------------------------( )--------------------------------------- 3750X -B2
Below the configuration that I have put the two stacks.
site A
interface Port-channel5
description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 11,12,999
switchport mode trunk
switchport nonegotiate
speed 100
But the problem is only one link is Bundeled in channel group, see below
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
5 Po5(SU) LACP Gi1/0/15(I) Gi2/0/15(P)
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies View RelatedI am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
model: SG300-52
version: 1.1.0.73
Switch is running in layer 3 mode.How can I turn off mDNS broadcast coming from the vlan interface on the switch.Getting mDNS broadcast from switch every 5 seconds.
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
I am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.
View 1 Replies View RelatedIs there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies View RelatedCatalyst 6509E Switch running IOS version 12.2. Created a new VLAN layer 2, created it layer 3 with an IP address. Issued the state active command and the no shutdown command. when doing a show vlan, shows in the list and active. When doing show int vlan xx, shows as down. Need to get it to be up, have attempted to assign a port to that VLAN in hopes it will come up, but still no go.
View 5 Replies View RelatedI am trying to configure Cisco SG300-52 switch for the first time and stuck without CLI configuration option. The configuration can be done using GUI, however, configuring using CLI would be more comfortable (as I am used to work with CLI of other Cisco switches)..
I was able to lo gin to switch using SSH, but the CLI appears in MENU format and was not able to find any way to go to CLI mode.
As per some blogs, in SG300 switches CLI mode can be accessed using Ctrl + Z in Menu, which did not work either in my case.
Switch is running with latest firmware version Sx300 Firmware Version 1.2.7.76.
I have three Cisco SG300-28 switches. I setup a test lab environment with a core (server) switch in Layer 3 mode and the rest are (clients) in Layer 2 mode. As I understand, these switches doesn't support VTP, only GVRP. And GVRP works the same with VTP. Whenever you create VLANs on the core or main switch, other switches will learn from the core switch and no VLAN creation for the client switches will be made. (Hope I got it right. I guess GVRP is more complicated than VTP). I want to use GVRP to create VLANs on the main switch so that I won't be doing it all over on the other switches. The following is my (so far) configuration through CLI only:I haven't use the web GUI. My SW version is 1.1.2.0.
1. I already enabled the GVRP globally.
2. I configured GE 12 & GE 24 as TRUNK ports for the core switch that connects both switches, I also configured GE 12 ports for both the client switches. All other ports are in ACCESS mode. (I am connected to GE 2 port)
3. I enabled GVRP on the TRUNK ports only for all switches.
4. I allowed all vlans on the TRUNK ports. (#switchport trunk allowed vlan add all)
5. All TRUNK ports registration mode is NORMAL and dynamic vlan creation is enabled on all trunk and access ports.
6. I created 3 VLANs without configuring its IP Addresses:
-vlan 2 = MGT
-vlan 3 = IT
-vlan 4 = MKTG
I don't know if I missed something on the configuration or the connection.
1. Is it necessary to enable all switches to layer 3 mode? Or depends on the network setup? Does this affect the GVRP?
2. Does switching ports to TRUNK mode means they are already 802.1q ports by default? Because I can't configure TRUNK ports to 802.1q (#switchport encapsulation dot1q) config like other switches. [code]