Cisco Switching/Routing :: 4500E QoS To Configure Access Port
Apr 25, 2013I have some cisco 4500E with sup7l-e and I want config acces port(with non-cisco ip phone), that cos and dcsp mark does not change.
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configure Access Ports Into Port Channel On Nexus 7K Switch?
Feb 14, 2013Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies View RelatedCisco Switching/Routing :: QOS On 4500E With Sup7-E?
Mar 25, 2012I was contacted by a customer today who is trying to configure QoS on a 4500E with Sup7-E. They are running:
cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin
And the 4500 is licensed for enterprise Services. I don't have access to the switch and am looking for configuration documentation and I am not finding the necessary configuration guides.
Cisco Switching/Routing :: 4500e Power Cables Connection
Jan 21, 2012Just received a couple of new 4500e chassis with the 2800ACV power supplies installed. I have not seen the cables they come with standard, the plug ends are considerably thicker than normal, what is the deal, do we need an electrician to come out and rewire or purcahse new powerboards?
View 2 Replies View RelatedCisco Switching/Routing :: 4500E Not Remember MAC After Connected To 2960s
Jan 15, 2013 client originally connects to the 4500E, moves to the 2960s and then cannot connect back to the 4500E.My design is a 4500E (configured for routing) and a 2960s. The 2960s is trunked to the 4500E, no vlan pruning.
Tried;
- shut/no shut port on the 4500E doesn't work
- no result for sh ip arp | i (clients mac) or sh mac address | i (clients mac) on the 4500E
The only way I can get the user back online is removing the 2960s, not a desirable solution as other clients are on the 2960s.
Cisco Switching/Routing :: 4500E SUP7L-E Shows Error In Log After Upgrading
May 14, 2012I upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
Cisco Switching/Routing :: Unsupported Module On 4500e SupV 10GE
Jan 17, 2012When i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies View RelatedCisco Switching/Routing :: Assigning IP Address Through DHCP On New 4500E Install?
Nov 20, 2011The DHCP/DNS server is on ip address 10.1.100.103 with an alt on .102 I'm attempting to integrate a 4510R+E into an existing network and use existing DHCP/DNS windows 2008 server to push out IP addresses to connected computers.
I want to assign a VLAN to every port for management purposes and then I put an IP helper address on every VLAN.
I've attached a the 4500E partial config. I'm attempting to get Gi1/44 to a state where I can plug a computer into it an resolve an ip address and gain internet access like all the devices on the existing network can do.
I've created a new scope in DHCP with the ip subnet of 10.60.211.0 255.255.255.0 It leases addresses from .1 to .253
The computer will not resolve ip addresses with this config.
Cisco Switching/Routing :: CAT 4500E Installed With WS-X4648-RJ45-E Module
Jun 29, 2012I have cat4500 with subject module. There is strange behaviour over module installed in 3rd slot only, some ports are connected, UP & working fine. But If I am connecting new ports over same module, are not coming UP.Duplex/speed settings already checked & are fine. If i connect same machine to any other module, it perfectly comes up & operation is fine.
View 3 Replies View RelatedCisco Switching/Routing :: Connect PC With Fiber Cable On Supervisor WS-X45-SUP6L-E Of 4500E?
Feb 23, 2012I have a problem connecting a PC in a TwinGig Convertors (GLC-LH-SM). I want to connect a PC with a fiber cable on the supervisor WS-X45-SUP6L-E of my Switch 4500E.
The default configuration mode is X2. As I want to deploy Gigabit interfaces (that is, use TwinGig Convertors), then I configured the associated port-group:
Switch(config)#hw-module module 1 port-group 2 select gigabitethernet
*Feb 24 06:18:37.125: Port Te1/2: TwinGig Converter inserted: vendor: CISCO
Switch(config)#do sh int status mod 1
Port Name Status Vlan Duplex Speed Type
[code]....
I noted that the Swicth set up automatically 'switchport mode trunk', so i put the command 'swicthport mode access' because i want to connect only a PC. But the status is the same, I can not achieve connectivity. i just want to know how connect a PC in the interface GigabitEthernet1/4 of the supervisor engine of my Switch.
Cisco Switching/Routing :: 4500E - Changing Default Etherchannel Load Balancing Algorithm
Mar 25, 2012Will there be some pause in traffic on formed ether channel interfaces (4500E switch), when i will change the default ether channel load balancing method to src-dst-port (or any other non-default method)?
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 4500 Versus 4500E Series - Blades Interchangeable?
Feb 6, 2013What's the difference between a Catalyst 4500 and a Catalyst 4500E series chassis? I believe it has to to do with supporting PoE+? Are the blades in both series interchangeable?
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 4500E Supervisor Engine 7-E / Possible To Deploy Simultaneously Both Type Of Ports
Aug 8, 2012We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
Cisco Switching/Routing :: Configure Port Forwarding On 887
Aug 11, 2012I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedCisco Switching/Routing :: L2 SG300 Want To Configure One Port As A Turn
Apr 3, 2013I have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 Replies View RelatedCisco Switching/Routing :: 1941 Router GE0/1 Port Burnt And Need To Configure
Aug 29, 2012I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedCisco Switching/Routing :: Telnet On Port 6066 To Configure Router
Apr 23, 2012We have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies View RelatedCisco Switching/Routing :: Configure Pop3 Port To Be Open On ASA 5505?
Apr 29, 2013I need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.
View 1 Replies View RelatedCisco Switching/Routing :: 4948E - Configure Switch Gigabit Port
Sep 11, 2012Trying to configure the Cisco 4948e switch gigabit ethernet port with "switch port trunk encapsulation dot1q", but didn't get the option. Please find below the options got after "swith port trunk"............
SW(config-if)#switch port trunk ?
allowed Set allowed V LAN characteristics when interface is in trunking mode
native Set trunking native characteristics when interface is in trunking mode
pruning Set pruning V LAN characteristics when interface is in trunking mode
SW(config-if)#switch port trunk. Please find below the version of the SW............
SW#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-LANBASE-M), Versi
on 12.2(54)SG1, RELEASE SOFTWARE (fc1)
Technical Support: {URL}
ROM: 12.2(44r)SG11
Hobgoblin Revision 21, Fortooine Revision 1.22
[code]...
So, whether the command is not supporting on this Cisco switch ? But we have Cisco 4948 Cisco sw where that command is working fine.
Cisco Switching/Routing :: Lose Lot Of Bandwidth Over Trunk Port (vs Access Port) 3750g
Feb 18, 2013I have a 3750g connected to a "core" switch stack of 7 other 3750g's via 2 GigE ports in a trunk. This is currently in a switchport mode access port- channel so only the default vlan data is sent over. Now we have a need due to physical location of these switches, to allow vlan20 (DMZ) from this 3750g to the switch stack. I will configure a few ports on the switch stack for vlan20 and they need to be able to talk to the stand alone 3750g.To do this I will change the port channel on both endpoints to
-switchport trunk ecapsulation dot1q
-switchport mode dynamic desirable
also making the appropriate change on the interfaces belonging to this trunk.My question is, now that its a trunk port that carries multiple VLANs, how much is the bandwidth reduced on that 2gbps link?I have a very active VLAN (10) on the stand alone switch, but on the core I'm not going to be assigning VLAN 10 to any ports. So does traffic from VLAN10 even come across the trunk (wasting bandwidth) if no ports on the core side are assigned to it? I really just need vlan 1 and 20 (for now).
Cisco Switching/Routing :: Cannot Configure Speed In Giga Port On WS-C3560-24PS-S
Oct 27, 2011I can´t configure speed in a giga port on WS-C3560-24PS-S switch(config-if)#speed ? no negotiate Do not negotiate speed
do you know if the port support speed 100??
because I need to connect with 2955C-12 switch in one port: 100BASE-FX (Multimode Fiber) uplinks, this port its only 100mbps?
and the switch C3750G-12S-E can I configure the ports on 100mbps?
Cisco Switching/Routing :: Possible To Configure QoS On 4500 Sup7 On Layer 3 Routed Port
Apr 26, 2013I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies View RelatedCisco Switching/Routing :: Can't Configure To 100 Full Duplex One Port From Target WS-X6724-SFP
Nov 2, 2011I would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies View RelatedCisco Switching/Routing :: Configure Multi-chassis Port-channel Between VSS And 3750X?
Feb 26, 2012Possible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
View 2 Replies View RelatedCisco Switching/Routing :: Configure Port-Channel Or Physical Interface On 3750
Jan 12, 2012how to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
3750 Config:
interface Port-channel2
!
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100
[code]....
Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.
Cisco Switching/Routing :: Configure 2960 8 Port Switch With DHCP Server?
Jun 24, 2012I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
Cisco Switching/Routing :: Stack 3750X - How To Configure Port Channel To Aggregate Two Links
Feb 18, 2013I have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
Site A Site B
3750X -A1 --------------------------------------( )--------------------------------------- 3750X -B1
( L-2-L )
3750X -A2 --------------------------------------( )--------------------------------------- 3750X -B2
Below the configuration that I have put the two stacks.
site A
interface Port-channel5
description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 11,12,999
switchport mode trunk
switchport nonegotiate
speed 100
But the problem is only one link is Bundeled in channel group, see below
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
5 Po5(SU) LACP Gi1/0/15(I) Gi2/0/15(P)
Cisco Switching/Routing :: 6500 Configure Switch Layer 3 Port Connected To Firewall
Feb 26, 2012I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies View RelatedCisco Switching/Routing :: 800 / Use ASA To Configure All The Vlans And Intervlan Routing And Access Lists?
Jul 4, 2012upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View RelatedCisco Switching/Routing :: C3550 - Configure Loop Back Interface On Gigabit Fiber Port
Sep 14, 2012I am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
Cisco Switching/Routing :: Configure LACP In 3750 For Two Port Connected To Dell M6220 Server Switch?
Aug 1, 2012We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
Cisco Switching/Routing :: 5520 Configure Traffic Flow Between Computers Inside VLANs And Routed Port
Jul 7, 2012How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
Cisco Switching/Routing :: Unable To Configure Access Server On 2509
Mar 26, 2012I am having trouble trying to configure my cisco 2509 cisco router for access server. I have two guides shown below: URL and URL
However I am running into some problems. I can go through the second guide up until it asks me to do this command
Step 5: Configure the transport input protocol on the async lines to Telnet.
Access_Server(config-line)#transport input telnet
I cannot put in Transport Input, I only have the option of doing Transport Output let me show some lines from my console:
---------------------------
Access_Server(config)#line 0 14Access_Server(config-line)#no execAccess_Server(config-line)#transport input ?% Unrecognized commandAccess_Server(config-line)#transport ? output Define which protocols to use for outgoing connections preferred Specify the preferred protocol to use
Access_Server(config-line)#transport
------------------------
Im not sure whats going on. I have two routers(cisco 2600 series) plus my 2509 cisco router I am going to use for a access server. I have a two switches 2950 series and I have the access server connected to all of them via a octal cable.
Here is the configuration from the access server:
--------------------------------------
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.3(26), RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 17-Mar-08 14:39 by dchih
cisco 2509 (68030) processor (revision M) with 14336K/2048K bytes of memory.
Processor board ID 22840809, with hardware revision 00000000
Bridging software.