Cisco Switching/Routing :: Can't Configure To 100 Full Duplex One Port From Target WS-X6724-SFP
Nov 2, 2011I would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Force Gigabit Ethernet Port To Be 1000 Full Duplex In Catalyst Express 500 Series?
Sep 1, 2007Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedCisco Switching/Routing :: GLC-T In C3KX-NM-10G - Full Duplex Does Not Work
Jun 4, 2013I have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
show interfaces g1/1/3 capabilities
GigabitEthernet1/1/3
Model: WS-C3750X-48P
Type: 10/100/1000BaseTX SFP
Speed: 10,100,1000,10000,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
[code]....
Cisco Switching/Routing :: 3750G-12S-S / Cannot Set Int G1/0/1 Into Speed 100 / Duplex Full
Aug 12, 20113750G-12S-S.Problem description:I had a WS-3750G-12S-S in production with a defective fan tray and needed to change it.I faced to trouble with inter g1/0/1 on the new switch( it worked fine on the old).
Here the config for old switch:
interfacigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 111-113,278,790
switchpmode trunk
speed 100
[code]....
even if I configure speed nonegotiate that does not work.
Cisco Wireless :: Configure GIG 0 Interface On 1552E Access Points To 10 Meg Full Duplex
May 19, 2013Is there a way to configure the GIG 0 interface on the 1552E Access Points to 10 Meg Full Duplex? Currently they will only work in Auto/Auto
View 3 Replies View RelatedCisco Switching/Routing :: 7604 WS-X6724-SFP - Can Apply Service Policy To Dot1q Main Port
Jul 9, 2012Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
Cisco Switching/Routing :: 4507 Switch Port Duplex Message?
May 3, 2012what is causing " Gigabit port is restricted to full duplex" while trying to hard code speed/duplex on a 4507 switch port?
View 3 Replies View RelatedCisco Switching/Routing :: Duplex Mode On HSRP Routed Port On 3750
Nov 15, 2012What should the duplex mode to be set on a routed port gi0/21 that are running HSRP ? I try setting the gi0/21 to full, but it caused the port to be down. The only way for the port to be up is setting it to half duplex.
Cisco 3750 Switch
==============
interface GigabitEthernet0/21
no switchport
ip address 10.200.104.34 255.255.255.248
[Code].....
Cisco Switching/Routing :: 3560X - Using 10 / Duplex Half On Gigabit Port Not Working?
Sep 24, 2012We recently upgraded the switch to which an old security device was connected. It worked fine on the old switch's FastEthernet port, which was configured for speed 10 and duplex half, as that is what the device required. The new switch is a 3560X with all Gigabit ports, but the security device's port, also configured with speed 10 and duplex half, does not connect properly.As a temporary test, we daisychained another switch that has FastEthernet ports, and the security device works again.Is there anything else that needs to be added to the configuration, when using Gigabit ports at 10/half?
View 4 Replies View RelatedCisco Infrastructure :: WS-2960 Gi Duplex Will Not Set To Full
Jul 28, 2011I have the following configurations for switch to switch connectivety. sh int sh config int
2960 will not take full duplex setting.
Core switch
WS-C4506 cat4000-i9s-mz.122-25.EWA10.bin
FastEthernet5/8 is up, line protocol is up (connected)
[Cdoe]....
Won't Recognize Connection With 100mb Full Duplex
Nov 6, 2012So I recently got a new computer today and it won't let me use my 100mbps of internet bandwidth. (Asus Sabertooth Z77 with an Intel 82579v gigabit lan controller) I noticed that at the LAN connection properties>Properties>Configure>Link Speed tab the 'Speed and Duplex' option was on Auto Negotiation and it was only accepting (or supporting) the 10mbps Full Duplex. When I switched it to 100mbps Full Duplex it would mark my connection icon with a red cross and when I clicked diagnose it said "Please connect your ethernet cable or your cable might be broken". So I tested my internet speed with that same cable on a different computer (laptop) and it worked with 40Mbps, so I don't think the cable is broken. Also I just recently downloaded some drivers but one was specifically for the Intel LAN controller but I'm a total noob for all of this computer stuff I don't know if it messed it up or something. Is it the motherboard that's not working correctly?
View 3 Replies View RelatedCisco WAN :: Set Ports From WS-C2940-8TF-S To Full And Half-duplex
Sep 28, 2011Howto set ports from WS-C2940-8TF-S to full- and half-duplex 100Mbit?
View 1 Replies View RelatedChange The Network Adapter Settings To 100 Full Duplex?
May 19, 2011If I change the network adapter settings to 100 Full Duplex, is there any changes that will take effect? even if we don't have Cisco switches in our network.
View 4 Replies View RelatedCisco Switching/Routing :: WS-X6724-SFP / How To Find Out SFP Vendor
Feb 3, 2013We have a 7609 in production network and I am trying to find out the SFP vendor plugged in module WS-X6724-SFP."show inventory raw" gives me the SN but not the vendor name. "show hw-module subslot 1/1" shows The indicated slot/subslot number is empty. Any commands which can show the SFP vendor?
View 1 Replies View RelatedCisco Switching/Routing :: Installing WS-X6724-SFP Hot Swap?
Nov 20, 2011I'm adding another module, WS-X6724-SFP, to our C6506E core switches. I read that it is hot swappable.
View 1 Replies View RelatedCisco Switching/Routing :: WS-X6724-SFP - Getting Minor Error
Sep 20, 2012The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see TestTransceiverIntegrity: on port no 2/11 has failed.
Is this a h/w issue?
==================================================================================================
S/w model : WS-C6509-E
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
==================================================================================================
1) TestTransceiverIntegrity:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . F . . . . . . . . . . . U .
Cisco Switching/Routing :: DFC3 For WS-X6724-SFP 6500 Line-cards?
Jul 17, 2012When quoting a WS-X6724-SFP line card for a Catalyst 6500:
1. If no Distributed Forwarding Card 3 (DFC3) is selected, can it be purchased at a later time as a spare part or the client needs to buy the line card with the DFC3 included from start?
2. Does each line card require a DFC3 in order to be able to perform localized forwarding decisions?
3. Does the DFC3 card is embedded in the line card physically?
Linksys Cable / DSL :: WAG320N With 100 Mbps Fiber Is Not Establishing Full Duplex Connection
Feb 26, 2011I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.
Cisco Switching/Routing :: 3750 / Access A Target Server With IP Address 10.2.2.13?
Oct 16, 2012Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
View 9 Replies View RelatedCisco Switching/Routing :: 880 W Router - Remote Computers Can't Connect To Target Machines
Jun 20, 2012I have and 880 W router. The LAN members can get out t o the internet. Now I want to configure NAT such that outside computers can access a couple of the machines using Remote Desktop (RDP). I am using Configuration Professional.
When I configure inside to outside, the remote computers can't connect to the target machines.When I configure outside to inside, the target machines acn't get to the internet.
When I try to use the advanced NAT definition wizard, I can't complete the task because the only inside pool (?) or LAN (?) is "designated" and not available to select. I can't free it up without deleting the one working NAT entry which is the one that enables all computers to reach the internet.
Cisco Switching/Routing :: Configure Port Forwarding On 887
Aug 11, 2012I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedCisco Switching/Routing :: L2 SG300 Want To Configure One Port As A Turn
Apr 3, 2013I have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 Replies View RelatedCisco Switching/Routing :: 4500E QoS To Configure Access Port
Apr 25, 2013I have some cisco 4500E with sup7l-e and I want config acces port(with non-cisco ip phone), that cos and dcsp mark does not change.
View 4 Replies View RelatedCisco Switching/Routing :: 2950 Cannot Seem To Correct A Duplex Mismatch
May 14, 2012I cannot seem to correct a duplex mismatch issue.I have a Cisco 2950 switch connected to a Cisco 2621 router. I am running a per-interface Vlan. I have two fastethernet ports and one NM-1E card installed on the router. One fastethernet port is connected to my gateway router, the second fastethernet port is connected to my switch for one Vlan. The NM-1E Ethernet card is being used for the second Vlan which consists of nine IP cameras. Though the cameras on the Vlan are working fine.Now, the NM-1E card is set to half-duplex. I know that I should be using a fastethernet module like a 1FE 2W or a 2FE 2W card, (which I have,) but the router does not recogonize either one of these cards when they are installed, and yes, they have been confirmed as good cards.
Using Router-on-a-Stick configuration is out due to the bandwidth contention besides the fact that the router I am using it on will not handle this due to the flash being an older version.I have forced the switchport to half duplex, setting the speed to 10. I was getting fewer error messages at first, but they soon increased back to the frequency that they began with.I have set the switchport to duplex auto, but this failed to resolve the issue.Obviously, I cannot force the switchport into duplex full since the NM-1E interface is set to half duplex. Can the NM-1E card be configured to full duplex? I can't seem to find any documentation showing where it can be forced to full duplex mode.Could nine IP cameras just be too much for both the router and switch to handle?
Cisco Switching/Routing :: Duplex Mismatch Between 2950 And 4503
Jul 8, 2012I have a 4503 switch (in L2 mode) running 12.1 hooked into a C2950 running 12.1, using regular 4 pair Cat5e cables to connect between them. The 4503 has Gigabit port 2/1 trunking to the 2950's Fa port 0/13.
When I set the duplex mode to DUPLEX FULL and SPEED to SPEED 100 on both switches (for their trunk ports) the link fails, and my 4503 loses connectivity (since it gets it from the 2950).
Here is my config from the switches (per description):
The 4503:
interface GigabitEthernet2/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,100-140
[Code].....
Note, this is the only mode that works (which seems to work fine, but I get TERRIBLE throughput for anything that goes over the 2950.
Cisco Switching/Routing :: 1941 Router GE0/1 Port Burnt And Need To Configure
Aug 29, 2012I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedCisco Switching/Routing :: Telnet On Port 6066 To Configure Router
Apr 23, 2012We have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies View RelatedCisco Switching/Routing :: Configure Pop3 Port To Be Open On ASA 5505?
Apr 29, 2013I need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.
View 1 Replies View RelatedCisco Switching/Routing :: 4948E - Configure Switch Gigabit Port
Sep 11, 2012Trying to configure the Cisco 4948e switch gigabit ethernet port with "switch port trunk encapsulation dot1q", but didn't get the option. Please find below the options got after "swith port trunk"............
SW(config-if)#switch port trunk ?
allowed Set allowed V LAN characteristics when interface is in trunking mode
native Set trunking native characteristics when interface is in trunking mode
pruning Set pruning V LAN characteristics when interface is in trunking mode
SW(config-if)#switch port trunk. Please find below the version of the SW............
SW#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-LANBASE-M), Versi
on 12.2(54)SG1, RELEASE SOFTWARE (fc1)
Technical Support: {URL}
ROM: 12.2(44r)SG11
Hobgoblin Revision 21, Fortooine Revision 1.22
[code]...
So, whether the command is not supporting on this Cisco switch ? But we have Cisco 4948 Cisco sw where that command is working fine.
Cisco Switching/Routing :: SF 302-08 Fiber Termination Is Multi-mode LC Duplex
Jan 2, 2012I am doing an small project, I have to connect 4 cisco switches SF 302-08 (1 GBIC each one) to a core switch SGE 2000 (4 GBICs). Because of cable length I have go connect all 5 switches with fiber. The fiber termination is multimode LC duplex. My confusion is on the mini GBICs. There is compatibilities issues i been reading. [code]
View 3 Replies View RelatedCisco Switching/Routing :: 6500 - Can Native VLan Or Duplex Mismatch
May 25, 20121 week ago, I got a call from a client that reported a network outage, the client told me that, 3 switch has crashed he try to console but it just hang. I ask him, did you change something? he said he didn't change anything, he just pluged a nortelswitch to the cisco switch number 9, but that switch doesn't crash like the others (3,4,8). I check the uptime, and yes the switch never been powered off..
the topology look like this
____ 6500 ____
/ / |
1 2 3 4 5 ...... 9
the vlan is end to end vlan, so vlan span between all those switches. transparant. this is collapsed topology, core and distribution is the 6500 itself all of the 1-9 access switch are in the same rack, with no loopguard, and bpdu guard configured. and connected to the core using etherchannel. the problem is there is no log available to start the troubleshooting/investigation.
Cisco Switching/Routing :: Cannot Configure Speed In Giga Port On WS-C3560-24PS-S
Oct 27, 2011I can´t configure speed in a giga port on WS-C3560-24PS-S switch(config-if)#speed ? no negotiate Do not negotiate speed
do you know if the port support speed 100??
because I need to connect with 2955C-12 switch in one port: 100BASE-FX (Multimode Fiber) uplinks, this port its only 100mbps?
and the switch C3750G-12S-E can I configure the ports on 100mbps?
Cisco Switching/Routing :: Possible To Configure QoS On 4500 Sup7 On Layer 3 Routed Port
Apr 26, 2013I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies View Related