Linksys Cable / DSL :: WAG320N With 100 Mbps Fiber Is Not Establishing Full Duplex Connection
Feb 26, 2011
I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.
So I recently got a new computer today and it won't let me use my 100mbps of internet bandwidth. (Asus Sabertooth Z77 with an Intel 82579v gigabit lan controller) I noticed that at the LAN connection properties>Properties>Configure>Link Speed tab the 'Speed and Duplex' option was on Auto Negotiation and it was only accepting (or supporting) the 10mbps Full Duplex. When I switched it to 100mbps Full Duplex it would mark my connection icon with a red cross and when I clicked diagnose it said "Please connect your ethernet cable or your cable might be broken". So I tested my internet speed with that same cable on a different computer (laptop) and it worked with 40Mbps, so I don't think the cable is broken. Also I just recently downloaded some drivers but one was specifically for the Intel LAN controller but I'm a total noob for all of this computer stuff I don't know if it messed it up or something. Is it the motherboard that's not working correctly?
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
I have been using a WAG320N since January. Around a week ago I came home to find the unit attempting to reconnect every few minutes - the DSL light flashing but nothing happening.
I replaced with an old Belkin unit which worked fine straight away.
i have upgraded the firmware, which made no difference, and secondly, tried a brand new unit, which strangly had the same problem even though the ancient belkin unit works first time and my original cisco unit worked for a couple of months before failing.
Are there any settings that relate to the DSL connection that may have been reset on the original unit? Could this be an issue related to signal quality or anything similar?
Everytime I post this message it keeps leaving out the contents...think it might be an IE9 issue.Does anyone know if its possible to see the duration of the internet connection on a WAG320N?
I've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
This is my DSL information from [URL] whilst connected OK
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 0/38DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel: DSL Upstream Rate: 1023 KbpsDSL Downstream Rate: 18723 Kbps Down up DSL Noise Margin: 9.1 dB 6.7 dBDSL Attenuation: 22.5 dB 12.0 dBDSL Transmit Power: 19.0 dBm 12.5 dBm--- Wireless Information ---Wireless Driver Version: 5.10.85.0.cpe4.402.4Wireless Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.
Got BT Infinity installed today, thought I would ditch the Home-hub 3 and go back to my tried and tested WAG320N. Got it configured, set the first ethernet port to WAN and got a connection.Ran speed test.net and comes out at 26Mbit.using the Home-hub 3.0 I get 37.5MBit.
This is a bit of a pain as the behaiviour is not consistent. whenever I connect to the Device webpage a number of things may happen
1. There is no connection - the page tries to load but never does. While this happens the router drops the ADSL connection and re-connects. I have to close the browser session and try again later. OR
2. The Browser session connects but at some point after the connection, say when I am trying to save changes or even just browsing through the config pages the session hangs, and again the router drops the ADSL connection and re-connects. I have to close the session and try again later.
I have noticed this happens when I use my OpenSuse 11.4 Linux Box using Firefox 5 or even using my Win 7 Box using IE9.
If I change the network adapter settings to 100 Full Duplex, is there any changes that will take effect? even if we don't have Cisco switches in our network.
I have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
3750G-12S-S.Problem description:I had a WS-3750G-12S-S in production with a defective fan tray and needed to change it.I faced to trouble with inter g1/0/1 on the new switch( it worked fine on the old).
Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
I am doing an small project, I have to connect 4 cisco switches SF 302-08 (1 GBIC each one) to a core switch SGE 2000 (4 GBICs). Because of cable length I have go connect all 5 switches with fiber. The fiber termination is multimode LC duplex. My confusion is on the mini GBICs. There is compatibilities issues i been reading. [code]
Got 300 Mbps with Linksys X3000 in real life?I haven't seen it working at 300 Mbps since I've bought it, so I wonder whether it is truly possible. The maximum speed I've seen was 130 Mbps.
My ISP (OTEnet, Greece) offers IPv6 connectivity in the form of dual-stack IPv4/IPv6 with the requirement that the router supports DHCPv6 Prefix Delegation for establishing an IPv6 connection.Using other routers (Cisco 887W, DrayTek Vigor2130n), I have established an IPv4/IPv6 connection but I am unable to do so with the EA4500. As a matter of fact, when I have the "IPv6 - Automatic" option enabled the router not only cannot obtain an IPv6 prefix from the ISP but it gets stuck in the connection attempt and never obtains an IPv4 or an IPv6 address. I have to disable the IPv6 option in order to simply establish an IPv4-only connection without problems.So, my questions are:
1. Does the latest (2.1.38.38880) firmware support dual-stack IPv6 and DHCPv6 Prefix Delegation?
2. If the router cannot negotiate an IPv6 connection why is it not establishing an IPv4 connection only but gets stuck in the process?
I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
I have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged LLC/SNAP g.dmt or ADSL2+ VPI 0 VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.
This WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.
I have the WAG320N. I know if my router is updated to fix the bug of the WPS?There is an update? Which is the date scheduled for release? The vulnerability of my network has been compromised yesterday because of this bug, so either the update is released soon or I'll have to switch to another product of some companies more serious
Transferring a file between a wired Win 7 machine and a wireless Snow Leopard mac seems to top out at 32Mbps.I've seen over 60Mbps on this laptop using N networks before, and when I wire the laptop I get a more respectable 240Mbps (presumably maxing out the server's disk I/O rate), so I'd say the issue is the router.
Things I have already tried:updating the firmware to 1.00.125Ghz modeFinding the least crowded 2.4Ghz channelswide channelsSetting network mode to N-onlySetting the transmission rate to 108Mbpschanging the beacon interval to 50, the frag threshold to 2201 and the RTS threshold to 2202
my router is connected to main router from my internet provider. When I use x3000 my download speed is half as fast as it should be (wifi and wired). When I connect to mian router directly (without x3000) both wifi and wired connection is at full speed.Is there any setting I should use to get full speed on x3000 - I have 24 Mbit/s?
