Does Cable Modem Mbps Dictate Or Limit Router Mbps
Mar 1, 2012In other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies
ADVERTISEMENT
Linksys Wireless Router :: WRT54G - .77 Mbps Download And .17 Mbps Upload Speed
Mar 11, 2013I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
Linksys Wireless Router :: E4200 Slow Speeds / 54 Mbps Wifi And 100 Mbps On Wired
Dec 22, 2011So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedLinksys Wireless Router :: WRT150N Is A 300 Mbps Or 150 Mbps?
Mar 15, 2013Which is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedIs There A Limit On Mbps For Windows XP On Wireless N Router
Nov 2, 2012I'm not able to connect at wireless n speed even though i have a wireless n adapter. i can force it but when i do my throughput drops dramatically, 20Mbps -> 1 Mbps. so i try, wpa2 security and can connect to router at 130 Mbps but throughput is 1Mbps when I throttle down connection to only connect at 54Mbps throughput is 20Mbps.
View 3 Replies View RelatedCisco Routers :: RVS4000 V1 Connected To Comcast Extreme 100 Mbps Cable Modem
Jul 24, 2011I have an RVS4000 V1 router connected to a Comcast Extreme 100 mbps cable modem.The port setting for the port (number 4) is 1000Mbps Full Duplex, auto Negotiate.why the RVS4000 is throttling the port?
View 3 Replies View RelatedCisco WAN :: 2951 - Installation Of 2x4 Mbps MPLS Circuit And 1x8 Mbps Ethernet Link
Feb 18, 2013Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
Wireless Gets 25 Mbps Down Speed And Laptop Gets Only 2.5 Mbps?
Jan 8, 2013I have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedD-Link DIR-825 :: 300 MBPS Connection Drops To 150 Mbps
Mar 7, 2011300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View Related150 Mbps Connection Drops To 72 Mbps
Jun 22, 2012I have a Netgear CG3100 modem hooked up to a Netgear WNR2000 router. Both are sending out signals, the CG3100 on channel 11 at 40 Mhz and the WNR2000 on channel 1 at 20/40 Mhz. I keep the WNR for legacy devices while the CG is for N devices only. They don't seem to interfere with each other much.Currently my computer is the only device connected to the modem wirelessly, with the only wired connection being the router. As I write this, the connection has actually dropped to 26 Mbps in the Wireless Network Connection Status window. I understand that this number drops under network load, but there doesn't seem to be any at the moment. If I go into the control panel and simply click apply, the connection jumps back up to 150 Mbps. However, this always drops back down, sometimes immediately, sometimes after a few minutes. It usually settles down at 72 Mbps, sometimes 54 Mbps.My wireless adapter is an ASUS PCE-N13 with v3.2.7.0 Ralink drivers. OS is Windows 7 64-bit.
View 6 Replies View Related100 Mbps On One Side Of Switch And 10 Mbps On The Other?
Feb 15, 2011I have 100 Mbps Half Duplex on one side of the Switch. ( Autonegotiation disabled )I have 10 Mbps Full Duplex on the other side ( Auto-negotiation disabled ). Should the link come up on both sides
View 4 Replies View RelatedUsing Netgear N Router Modem Combo DGN-2000 And Readings Are Just Over 12 Mbps?
Feb 14, 2013I recently went to a higher speed ADSL which claimed to be 16Mpbs.. It is with Acanac and when i first tested with speed net it came in over 14Mbps. I was using a netgear wireless g router (old) with the 4200 speedstream modem and got these results which I found acceptable. Now using netgear n router modem combo DGN-2000 and my readings are just over 12 Mbps. I tried reverting and still got the lower speeds. I tried isolating one computer hard wired still got the lower 12Mbps.It hasnt really affected my download speeds as far as I can tell but I did find it a little puzzling.
View 2 Replies View RelatedD-Link DIR-655 :: 4 Mbps Upload Via CAT5 But Only 1 Mbps Upload Via N-format Wireless?
Jun 30, 2011I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
Linksys Cable / DSL :: Get 300 Mbps With X3000?
Aug 8, 2012Got 300 Mbps with Linksys X3000 in real life?I haven't seen it working at 300 Mbps since I've bought it, so I wonder whether it is truly possible. The maximum speed I've seen was 130 Mbps.
View 7 Replies View Related100 Mbps Lan Works On 10 Mbps Only?
Sep 4, 2011i have a 100 mbps lan. but 1 computer works on only 10 mbps half duplex mode why??
View 4 Replies View RelatedDell :: Vostro 3300 - Replaced New High-end Wireless-N 300 Mbps DSL Modem
Feb 13, 2012I was bought a Vostro 3300 couple months ago and with this, laptop dell dw1501 a/g/b/n wireless network card was provided.
I trust to Dell's specifications and replaced my DSL modem with a new high-end Wireless-N 300 Mbps DSL modem without thinking any compability problem. When I went to home and setup my new modem, my Vostro 3300 connected with only 72Mpbs. I tried to find a solution and find this community topics mentioned below. url...
As you wil see, the dw1501 wireless network card is not support this connection speeds even though the card is advertised as a wireless N card. Some users managed to replace their card with the better ones.
Linksys Cable / DSL :: WAG320N With 100 Mbps Fiber Is Not Establishing Full Duplex Connection
Feb 26, 2011I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.
What Does It Mean By 300M Or 300 MBps Router
Jun 26, 2012I have a TP Link router which is written as 300M wireless router in the home page when I login into it.
I can think of it as 300 Mega bits per second router. Does it mean it can support upto 300 MBPS internet speed or something like that?
Use 100 Or 300 Mbps Wifi Router As Bridge?
Jan 7, 2012I am wondering if I should use my old 100 mbps router as a bridge and use the 300mbps one as the main. Or vice versa. I will mostly be gaming on the bridged router and will have a cat6 going from the router to the computer.
View 5 Replies View RelatedWhy Only 100 Mbps Wireless On New Linksys Router
Jul 24, 2012Contrary to what i have been reading, i have a DOCis 3 Modem, on Comcast, with an internet connection of 1GB. My wireless connections are in the 150-300 Mbps range thru a Linksys 4500N router
View 1 Replies View RelatedWireless Router For 1 Mbps Internet Connection?
Jan 25, 2012I have 1 mbps internet connection and I got two computers to be connected. optimum configuration of the router required.
View 5 Replies View RelatedLinksys Wireless Router :: E3200 Only Getting 130.0 Mbps?
Jun 21, 2011after messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies View RelatedLinksys Wireless Router :: Only Getting 130 Mbps With E4200?
Dec 28, 2011I bought a Linksy E4200 yesterday and set it up fine, but I only seem to be able to get 130 Mbps on my Wi-Fi. I looked through these threads and tried disabling the 2.4Ghz band and it still remains at 130Mbps. There was no change, also read I can try set up a secondary SSID. I really don't know much about routers or configuring them
View 4 Replies View RelatedCisco WAN :: Can WIC-2T Support 4 Mbps On 2821 Router
Dec 13, 2010Support for WIC-2T , we have one 2821 router with wic-2t currently serial link is running with 2mbps and we want to update with 4 mbps
View 2 Replies View RelatedCisco WAN :: Router 3945 Log To Get 100 Mbps As Sum Of Tunnels
Aug 9, 2011I am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??
Linksys WRT54GL 802.11a/b/g Wireless Router - 15 Mbps ISP
Mar 16, 2011I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
Linksys Wireless Router :: Cannot Reach To 450 Mbps With EA4500
Feb 8, 2013I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
Linksys Wireless Router :: E1000 Slows Internet (10 Mbps)
Jul 13, 2011Why my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 Replies View RelatedLinksys Wireless Router :: WRT160N Speed Is Very Slow (0.5 Mbps)?
May 25, 2011I have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies View RelatedLinksys Wireless Router :: Wrt610n - 100 Mbps Speed Internet?
Jun 29, 2011I have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedLinksys Wireless Router :: E1200 Speed Slows To 15 Mbps
Apr 29, 2013When I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies View RelatedLinksys Wireless Router :: EA2700 - Usable Range (11.0 Mbps / Low)
Aug 3, 2012My new (30 days old) EA2700 has probably less than 40 feet of usable range without obstructions. Is this normal?
I've got the router sitting at the end of the hall, and I'm at the other end without anything between and I'm at 11.0 Mbps/'Low' on my laptop.
Cisco WAN :: Router 2951 Is Suitable For 100 Mbps MPLS Link?
Aug 28, 2011I want a router to terminate 100Mbps MPLS link on it. Can Cisco 2951 will be suitable for this or i have to go on to 3900 series or 7200 series
View 2 Replies View Related