Why my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 RepliesWhen I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies View RelatedI purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies View RelatedI just "upgraded" from an E1000 to an E1200 wireless router. I had good performance with the E1000, and I only upgraded to the E1200 because it was on sale.My only complaint with the E1200 is the slower download speed on my desktop PC that is connected directly to the router. My normal download speed on the desktop PC was 25 Mbps with the E1000 model. After I disabled the WMM on the E1200 as others suggested, the download speed on the desktop machine immediately increased from 5 Mbps up to 15 Mbps. Any other suggestions to get the download speed up to 25 Mbps before I switch back to my E1000? The E1200 router is connected to my Arris TM602G modem. Both modem and router were reset during the installation process. I setup parental controls for a couple of iPods and configured Open DNS, but other than that, the router is using default settings. All wireless devices in the house seem to be performing fine with the E1200.
View 8 Replies View RelatedI just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedWhich is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedI have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedI am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies View RelatedI've had this router for about 3 weeks. It's only 20 feet from the computer, but my computer on 2 or 3 separate days had trouble staying connected. The signal dropped to 5 Mbps and had a little yellow symbol that said no internet access and when I looked at the properties it said, "limited or no connectivity." I got impatient and purchased a 75 ft Ethernet cable online with plans to possibly return the router as I don't really need wireless anyways and since I spent $100 on this router I expect it to work at 20 ft distance.
For the last few days it has remained at 54 Mbps or more sometimes all the way up to 108 mbps. But now since it got pretty low a few times I don't trust it enough so I might return it anyways.IPv6 connectivity says no network access. This might be because when it asked for administrator password to recognize it as a trusted home network I closed it instead of putting in the password.
my brand new Linksys E1000 wireless router. I am really struggling and cannot figure out what I am doing wrong.
I live in The Netherlands, have a modem (DSL I think...) and can connect wired through the modem with no problems.
I installed the E1000 with the CD, followed all the steps and my laptop is finding the network. However, it's only local, no internet and I don't understand why. Have tried to connect (wired) my computer to the E1000 and the E1000 to the modem but that doesn't work either.
Just got the new Linksys E1000, and follow the Cisco Connect to setup. No IP received from the service provider (which is Fibre-to-the-building, no modem is required). Goto the setup page and confirmed that the connection type is "DHCP".Once i unplug the cable from E1000 (internet port) and plug into my old wireless router, everything work nicely. The internet connection & cable itself seems fine. Switch the cable into notebook, and get the IP as well, it seems the service provider didn't lock the mac address of the devices (routuer nor PC). Cloned the mac address but nothing improved.Tried release the IP before unplug from the old router, switch off old router, and wait 10mins before connected to E1000 but still no luck.
View 2 Replies View Relatedcannot conect to the internet with my e1000 wirele
View 1 Replies View RelatedEvery two or three days I'm unable to reconnect to my wifi network when I turn on my Windows 7 laptop or Android tablet. I have to power cycle the wifi router to get the connection again. This usually happens after I haven't used either device for a day or two. The connection usually does not drop when I'm using them. Restarting the computer or the tablet does not work and using the Windows troubleshooter (or the android app for wifi issues on the tablet) also doesn't work. Both computer and tablet recognize the network and say the signal is strong but won’t connect to it. There are no physical obstructions. I have no problem with my internet connection (cable modem). The problem really seems to be with the wifi router.
Model name: Linksys E1000
Model number: E1000
Firmware version: 2.1.02 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11069.2
Connection type (WAN): DHCP
I have a Linksys E1000 device that is connected to a DSL connection through a modem. I have a Laptop that is wirelessly connected to the router and a PC that is connected via cable. Lately, a problem started to occur where the router keeps losing the internet connection and Laptop tell me that it connected to the router but there in no internet access and the same thing happens to the PC, both disconnect at the same time. I called my ISP company when this happens and they told me that the connection is working fine and everything look ok from there. I connected my PC directly to the modem and it worked fine so problem is not from modem. When i go to the router settings at the moment this occurs, it shows that all IPs are 00000 and status is "Connecting" and then it connects and changes to "connected" and everything fine till like 15 minutes later where this happens again (sometimes, it actually disconnects again after like 15 seconds!). I took the router to the dealer and he examined it and told me there is nothing wrong but he updated the firmware and told me to try it but same thing so he exchanged it for a new one and problem is still there!
View 3 Replies View RelatedI got a refurbished E1000, has been great.
Using it w/ my HP laptop since July, just got Mac book and was trying to use w/ that addition laptop but could not find router password, also 192.168.11 would not let me access w/ password: admin, so I reset the router and renamed it. NOW my HP laptop shows my router connected, BUT will not access internet.
I've got a v1 E1000. Lately when I turn on one of my computers, or attempt to connect with my Motorola Xoom tablet it will show connected but I will not have internet access. Initially it will show that I have internet access but not work, then after about 1-2 minutes my PCs will show "No Internet access" for about 2-3 minutes, then it will show "Internet Acess" again and still not load. After that, in about 1-3 minutes the internet will start working and work as good as ever until I disconnect (manually or by turning off my computer) then connect again; the process described avove happens again.
View 2 Replies View RelatedI recently bought a new router but I'm having issues with it. We have 2 Laptops in our house and 1 (windows 7) can connect to the router and get internet access but the other (windows vista) can't it says that the Cisco router is not connected to the internet but it is. I've tried everything, resetting, reprogramming, etc. I recently found that the windows 7 one had the software installed and the windows vista didn't. What I need is to get that software but I need to know which version to get. How do I know which version of the software goes with my computer?
View 1 Replies View RelatedI have an ADSL modem connected to a Cisco E-1000 router. I have two laptops (Windows Vista and 7), an iPad and two smart phones. The iPad and the phones connect without any problems at all and stay connected without interuption. But the two laptops keep losing internet access! They stay connected 10-15 minutes, then invariably lose internet access. I have to manually disconnect and reconnect again to get back on the net - but again, only for 10-15 minutes.
I've tried many things - changing the channel, playing with all sorts of parameters (as suggested by the online chat guy) - but to no avail.
I have a Cisco E1000 v2. I updated to the latest Firmware 05/25/2011Ver.2.1.02 (Build 5).
Before doing this update I did get 300mbps N speeds. Now I don’t using the same settings, it max out at 144mbps speed. Also the router only seems to get B speeds when using a channel other than 11. I did do a hard reset after the firmware update.
I have the router plugged in for internet but do not know the password for the wireless connection. i am running a mac.
i have also tried using the standard admin or password as passwords to get in and am unable too.
Linksys E1000 running on Window XP
Trying to access the internet with a dell laptop after my daughter messed with the router. She gave me the passowd but when I try to log in from the laptop that has never been logged on since the pw changed, I get a message that wants the network key. I have read several posts about getting the network key but didn't see a network key.I have cisco connect on a different computer and can access the details of the router but haven't found the network key. I can get to Wireless, Wireless Security and the security mode is WPA2/WPA. I can see the password but where is the network key?
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 2 Replies View RelatedIf I have a wireless network set up with the Linksys E1000 using one internet provider and then change the internet provider service to someone else, do I have to reset up the network or is it simply a matter of connecting the new internet service to the router?
View 3 Replies View Relatedi have my E1000 network detected by laptop and devices but can't connect to Internet. The E1000 is connected to Cisco 2100 modem and I can connect to Internet if I plug my laptop/PC directly to Cisco 2100 modem.
View 2 Replies View RelatedWhy is it that my netbook doesn't have internet access on my Private Network? But when I connect it to my Guest Network, it does have an internet access. It's the only device I have that doesn't have internet access on my Private Network. The rest are working. I tried all the possible options to connect a device but still the problem exist.
By the way, I'm using E-1000 v2.1.02
I just bought a E1000 and connected it to my cable modem. I can connect to the internet with my wired PC and wired Xbox 360 with no problems. For some reason on my wireless laptop I can only connect to the internet by the Guest connection. When I connect to the regular router SSID I get local only access, no internet.
View 2 Replies View RelatedWas told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies View RelatedI have the E1000 Linksys Router and I am using a network cable to connect to my Sony Blu-ray BDP-S370. When I watch HULU through the player it kills the entire internet connection for all PCs. I have to unplug the router in order to restart it. Everything will also work just fine until the next crash.Here's the thing, I'll watch a bit of the show and see the commercials and the router will only crash when it comes back to the show. If I watched 100 commercials they would not crash, but as soon as it returns to the show CRASH. Restart and we watch again.
View 2 Replies View RelatedEver since I started using iPads at the house I have had to reboot the router about once a week because the download speeds drops by approximately 90%. As soon as the reboot completes all is right with the world for about another week. During the course of the week, but not all at once, we will have 4 iPads, 3 iPhones, 2 laptops and one desktop(wired), a Verizon signal booster and house guests. I have updated the firmware.
View 1 Replies View RelatedI just installed my new EA6500 and everything works ok I think, Netflix across my PS3 is ok, laptop connects, and smartphones connect. The problem is that my Internet connection to my desktop (wired) PC is slow as mud. My ISP is a fiber optic provider and although I'm not sure exactly what my connection speeds are my Internet connection has always been blistering fast. With everything other than two smartphones turned off my desktops Internet access is slow. How to get my speed back and still use my new router?
View 2 Replies View RelatedWhen connecting wirelessly (5GHz) to the E3000 after a day or so the wireless connection starts loosing speed. I have Comcast and usually get 20-30 MB download connections. After a day or so I start to lose speed (down to 5MB) until I reboot the E3000. Then I resume 20-30MB download connections. My wired connections appear fine and don’t experience the slow down. I'm doing my speed test with [URL]
The wireless slow down seems similar to the old memory leak condition of old Windows OS’s. Called Cisco and they don’t have an idea. They had me change a few settings (channel info) but I’m pretty technical and don’t feel that will fix it.
My WiFi is working, but only to about 20 feet then it slows down to almost nothing...
View 1 Replies View Related