I have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
I have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies View RelatedWhen I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies View Relatedi used my 610N v2 for 2 years and recently i upgraded my network from 100mb to fiber 500mb , however, if i directly plug the lan cable to my computer , i can get full speed , but with 610N, the speed is limited to 130 for both upload and download .i had already upgrade my firmware and did factory reset, none of them work. Is it the limitation of the router ?
View 1 Replies View RelatedI posted this in the wired forum, because it's the wired speed that is limited, but it looks like there's more E4200 expertise over here, so here it is again:
I have Hotwire fiber service and the plan is supposed to provide 20 megabit downlink speeds.
I just bought a Linksys/Cisco E4200 to replace an old Dell TrueMobile 2300 from 2004. With that router I got the full advertised downlink speed.
Now, when I run a speed test with the E4200 in place, the downlink speed is only 5168 kbps or so. Watching the speed test meters, I see the data arriving in bursts, every few seconds a whole lot of it gets through, then for a second or two nothing. It's pretty regular.
But, if I run a speed test with the ONT cable plugged right into a laptop, I see 19001 kbps - close enough to 20. This is the same cable that plugs into the back of the router.
With E4200 in place Direct into laptop what I can check or configure in the E4200 to change this behavior?
I purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies View RelatedI'm running a Cisco E4200V2 router with the latest firmware (2.1.4.12284) on an iMac running OS X 10.8. My ISP is providing 15Mbps to my modem, which I've confirmed by connecting directly to it without the router. Once I put the router back in the path, my broadband speed drops to about 6 Mbps. Is this the best I can expect from this router?
View 2 Replies View RelatedI have been using a WRT610N router for several years. A couple of weeks ago I purchased an iPad 2. I am not sure if its a limitaion of the iPad 2 or a wireless connection speed issue, but when watching You Tube music videos the video stops frequently and I have to hit the play button again to resume. This occurs more often if I am using Blue Tooth connected headphones than direct connected headphones, leading me to the initial conclusion that I am witnessing the limits of the iPad 2 processor. However, I recently downloaded the Speed Test app and have discovered that the wireless download speed varies from about 11-15Mbps, depending on the location (normal vs next to router). If I go to that web site and run the speed test there from my direct connected PC (connected to 1Gbps port), I get a download speed typically of 36Mbps (inflated I know because Comcast speed supposedly is limited to 25 Mbps).
View 2 Replies View RelatedI just "upgraded" from an E1000 to an E1200 wireless router. I had good performance with the E1000, and I only upgraded to the E1200 because it was on sale.My only complaint with the E1200 is the slower download speed on my desktop PC that is connected directly to the router. My normal download speed on the desktop PC was 25 Mbps with the E1000 model. After I disabled the WMM on the E1200 as others suggested, the download speed on the desktop machine immediately increased from 5 Mbps up to 15 Mbps. Any other suggestions to get the download speed up to 25 Mbps before I switch back to my E1000? The E1200 router is connected to my Arris TM602G modem. Both modem and router were reset during the installation process. I setup parental controls for a couple of iPods and configured Open DNS, but other than that, the router is using default settings. All wireless devices in the house seem to be performing fine with the E1200.
View 8 Replies View RelatedI've recently subscribed to a 100Mbps fibre broadband service with the bundled Huawei EchoLife HG8240 ONT modem and speed-tested it with an achievable speed of almost 100Mbps (uplink and downlink) on my desktop PC.However, when I connect my new Cisco Linksys E1200 Wireless-N Router to it, I noticed the speed dropped by almost half (about 50Mbps both ways) when I conduct a similar speedtest .
note that I'm using wired cable and there's only 1 single PC connected to it and it is not shared. This includes upgrading the firmware to the latest version, disabling the IPV6 setting and configuring QOS.My current hardware/ firmware version is as follows:
H/w ver : 2
F/w ver : 2.0.03
i have WRT610N v1.0 with latest original firmware but ftp upload speed and torrent download speed is terribly slow.
View 3 Replies View RelatedI just bought a refurbished E2000 wireless-n router with 1 Gb LAN ports (from Cisco online).This router is meant to replace my Netgear wireless-n router that only have 100 Mb LAN ports.I have 10 devices in my home network, 6 of them are using wireless (1 'g' and 5 'n') and 4 are interconnected with cat5e cables (trough the router).The devices have some different operating systems and their network adapters are from different brands.When I set up the Netgear router I didn't have to adjust anything for the wireless network to work fine.All wireless-n devices worked at 150 Mbps (sometimes going down shortly to 130 Mbps).The wireless-g device worked at 54 Mbps.For the last 2 days I've been trying to set up the E2000 to achieve a wireless-n speed higher then 72 Mpbs... without success.I tried all the suggestions that I found in the Cisco Knowledge Base.
- Upgrading the firmware to the latest version
- Trying different channels and channel widths
- Different wireless security methods and many others.
Also trying different settings on the different devices doesn't work.Changing the distance between router and devices as well as changing the location of the router don't affect the results.Switching on only 1 device at a time doesn't change anything either.It looks like the E2000 is set to not transmit on a higher speed than 72 Mbps, when it's actually supposed to achieve a wireless-n speed of up to 300 Mbps. I would be lucky if I get the half of it, but not if it's only one fourth.
I have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedI am working on an assignment for college and I was wondering if 1.01 mbps is a good internet download speed for a wireless computer?
View 1 Replies View RelatedSo I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedWhich is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedI recently installed an E4200 router/AP and, on one desktop, an AE2500 USB Adapter. All the other devices on the LAN work fine and the laptops, even show improved tranfer rates. The desktop, with the AE2500, shows good or very good signal strength, but the speed is down around 5.5 Mbps. Running a full backup of the HDD proves the slow speed.
View 7 Replies View RelatedWhy my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 Replies View RelatedI am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies View Relatedi have Cisco 3845 with 1 GB SFP, my company using fiber as backbone to isp, i have new internet connection 310 Mbps, does that enough ? does that for port only for LAN or also for WAN ?
View 8 Replies View RelatedI am trying to access the internet trough my WRT610N connected to a ZyXEL P-2601HN provided by my ISP.
I have the WRT610 all setup and working, but I cannot connect to the internet. The WRT610N is a the latest firmware version.
The WRT610 is connected (Internet) by cable to the Zyxel (one of the four ports)with a cat.5E patch cable.
the wireless is so much better on the WRT610N than the ZyXel.
The Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies View RelatedI am trying to configurate a WRT610N router that is connected to an ADSL modem.
I set this as DHCP, but in the status page I am only getting the Internet Address of 127.0.0.1.
The ADSL modem IP is 192.168.1.1, but I cannot have access to the modem configuration,
I've had this router for about 3 weeks. It's only 20 feet from the computer, but my computer on 2 or 3 separate days had trouble staying connected. The signal dropped to 5 Mbps and had a little yellow symbol that said no internet access and when I looked at the properties it said, "limited or no connectivity." I got impatient and purchased a 75 ft Ethernet cable online with plans to possibly return the router as I don't really need wireless anyways and since I spent $100 on this router I expect it to work at 20 ft distance.
For the last few days it has remained at 54 Mbps or more sometimes all the way up to 108 mbps. But now since it got pretty low a few times I don't trust it enough so I might return it anyways.IPv6 connectivity says no network access. This might be because when it asked for administrator password to recognize it as a trusted home network I closed it instead of putting in the password.
My main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.
View 3 Replies View RelatedI was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies View RelatedWe have p2p link that interconnects our data centers and the bandwidth is 150 meg link.In the current architecture, one end of the link is Nexus 7k (data center 1) and other end is catalyst 65k (data center 2)..We are planning to migrate this link to routers. We planned to install 3945 router on both data center and move the p2p link to this routers. [code]
View 2 Replies View RelatedI hava installed a WLC 2106 with 4 1252 Aps. Some laptops has dual radio wireless card, but others has just 2.4 Ghz card.
I have one SSID with WPA2/AES and 802.11X authentication.
With the laptops with dual radio the speed is in 300 Mpbs, but when is single 2.4 radio the max speed is 70Mpbs
If i use a 1252 ap with autonomous IOS, SSID with WPA2-PSK/AES this laptops single in 2.4 works to 144 Mbps
is there a knowed issue about 802.11x in 2.4 Ghz or i need to make a different configuration to can work in 2.4 with a speed of 144 Mbps?
My Inspiron M101z which I bought last year is supposed to have 802.11n wireless support. However, my wireless speed never exceeds 72.0 Mbps no matter what I do. My router is Linksys WRT160N v3. I've tried everything, setting mode to N-Only, setting channel width to 40Mhz. The result is always the same, I'm getting 72 Mbps max. This speed makes difference when transferring files between computers in the network. All my computers are running Windows 7 x64.
View 2 Replies View RelatedI have 1 mbps internet connection and I got two computers to be connected. optimum configuration of the router required.
View 5 Replies View Related
