I am trying to configurate a WRT610N router that is connected to an ADSL modem.
I set this as DHCP, but in the status page I am only getting the Internet Address of 127.0.0.1.
The ADSL modem IP is 192.168.1.1, but I cannot have access to the modem configuration,
FiOS gave me an Actiontec router that every other day is getting into a state where it refuses to give out IP addresses via DHCP. I have to reset the router to get it to work again.This seems ot have started in the last year, I assume due to some piece of equipment I added, or perhaps the VPN software or Windows 7 installed on my work laptop. I've not been able to figure out what is tripping up the Actiontec router, so I decided to try moving the DHCP function over the WRT610N that I have. I basically had the WRT610N setup without DHCP enabled, no NAT and no RIP, so it was basically just working as an access point. I left the Actiontec at 192.168.1.1 and assigned 192.168.1.2 to the WRT610N on the LAN side, while the WAN side is left disconnected.
I disabled DHCP on the Actiontec and enabled it on the WRT610N. I also set the DNS server to 192.168.1.1 so it would go to the Actiontec for name resolution. Using nslookup from a command prompt on a PC wireless connected to the WRT610N, I can see that names are indeed getting resolved. However, it looks like the WRT610N is setting itself up as a the gateway at 192.168.1.2. When trying to ping something out on the net, I get a message back saying that 192.168.1.2 is reporting the address as unreachable.
I assume this is because the WRT610N is handing out its own address (192.168.1.2) as the gateway. Is there anyway to get the WRT610N to hand out a different gateway address than itself? Optionally, is there a way to get the WRT610N to route requests coming to it over the Actiontec?I suppose I could just ditch the Actiontec altogether, but it seems a bit easier to use to setup port forwards and the like for various servers we have running. It also has a coax MoCA interface which I believe our FiOS set-top boxes use for their internet connectivity, so I don't want to lose that.
2 of my attached wireless devices have the same IP address different MAC address. How can I assign unique address to each of the devices
View 1 Replies View RelatedI have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedI am trying to access the internet trough my WRT610N connected to a ZyXEL P-2601HN provided by my ISP.
I have the WRT610 all setup and working, but I cannot connect to the internet. The WRT610N is a the latest firmware version.
The WRT610 is connected (Internet) by cable to the Zyxel (one of the four ports)with a cat.5E patch cable.
the wireless is so much better on the WRT610N than the ZyXel.
The Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies View RelatedMy main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.
View 3 Replies View RelatedI was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies View RelatedThe problem is WAP 610n not assigning IP address through DHCP; i have to add IP address mannualy.
just go through the details below:
In my network environment we are using :
CISCO Router 800 series; IP: 192.168.1.1
Domain server with DHCP server : 192.168.1.2
DHCP pool: 192.168.1.234 - 192.168.1.250
WAP IP : 192.168.1.236
WAP configuration :
configuration view : mannual
Wireless band : 2.4 Ghz
Network mode : mixed
channel width: 20 Mhz only
standard channel : auto
SSID broadcast : Disabled [ for security reason]
Security mode : WPA2 Personal
Encryption : TKIP/AES
Firmware : 1.0.01 build 94, Oct 26, 2009
Note: In status menu it is not showing any default gateway.
Encapsulation method in CISCO router : PPPoA [ as instructed by ISP]
To connect the Linksys WRT54GS to a Microchip DV102411 WiFi Comm Demo Board I need the IP address assigned by DHCP. The WRT54GS Administration Log is enabled but there is no Incoming or Outgoing network activity. The DV102411 sees the SSID linsys when scanning for wireless networks and attaches to it but once attached I need to know the IP address the DV102411 has been given by the WRT54GS.
View 2 Replies View RelatedI have a WRV4400n in my company and almost every day I have to reboot so people can get out to the internet, It lets you see the local network also if I put a desktop on line it will not give a DHCP address, untill I reboot the router. then all is fine, It has the latest greates firmware.
View 1 Replies View RelatedI've got threeLinux Boxes (running Centos 6). They were all connected to my cheap WRT54GL-- DHCP worked every time.Absolutely no problems. Both the LInux boxes and the WRT54GL had MTU set to manual, 1492.I replaced the WRTt54GL with the expensive E4200. I set the new router's MTU to manual, 1492. NONE of my Linux boxes ever receive a DHCP address. I look at the logs, and they do DHCPDISCOVER, get DHCPNACK, try several different intervals, and then fail the interface and quit.ALL I did was unhook cables from the WRT54GL and plug into the E4200. Yes, the WRT54GL was powered off. NOTHING was changed in the Linux configs. Yes, DHCP is enabled, address-range assigned, etc. BTW-- one box is dual boot with Win7-- in Win7 (using the same card, obviously), DHCP works just fine. But, Linux doesn't work.
I can give the boxes static IP's, and all is well. Just can't get DHCP to work. I evfen tried putting in DHCP reservations (via MAC assignments) for the E4200-- still doesn't work. The new E4200 is on the 02 firmware (which I believe is cuurent). If I can't iron this simple task out, in a couple of days I'm taking the E4200 back, and getting a refund. I'll stay with my old WRT54GL... it works. Hate to give up on some of the new E4200 features, though.
I've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
View 9 Replies View RelatedI have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?
View 1 Replies View RelatedE4200v2, firmware 2.1.39.145204
Router says "Invalid IP address" when I try to make a manual IP address reservation of the IP address range.
Example: local network 192.168.1.0/24, where .1 is a router, .2 is a reservation, .20-.50 is a range for DHCP.
Before upgrade I didn't have this problem.
After an upgrade of the WRT120N to firmware Ver.1.0.06 (Build 01) every device I have tried to use WPA authentication with will authenticate / associate with the device then drop the connection just prior to recieving a DHCP address.I have tried a Dell latitude laptop with the broadcom chipset, an iPhone 3GS as well as an motorola with google pad device and all experience the same problems.I have removed all mac address filtering, and re-enabled the essid broadcasting only to have the same problem persist despite stripping everything down to just WPA.
View 2 Replies View RelatedI purchased a WRT610N router early this month, the wireless network was working completely fine when I first set it up. Today I tried to connect my laptop to my wireless network. The laptop isn't able to connect at all. I also got a Sony PSP which has WLAN on and that saying it cannot detect any access point which would be my router.
View 3 Replies View RelatedHow can I open the Nat for both systems on my single router.
View 2 Replies View RelatedI was told that this router would push the PoE to the WAP4410N. I hooked the AP up to port 1 and no lights or anything... The network is all cat6, patch cords are cat6 shielded if this matters at all... what am I missing.
View 3 Replies View RelatedIs it possible to have 2 hard drives connected to a WRT610N perhaps connected through a USB hub?
View 1 Replies View RelatedI have the Linksys WRT610N wireless router and would like to know if it is possible to block all domains ending in .XXX? The access restrictions let you type in a 'specific' URL, but using a generic domain name doesn't seem to work. I basically want to block all access to any URL that ends in .XXX.
View 5 Replies View RelatedI just bought a certified refurbished router. The model is WRT610N-RM. Where's what I've done:
1. Downloaded newest firmware from the site using old router, Then disconnected. Connected a lan cable to the new router. Powered up the router. Held down reset untill the light blinks. Went to the browser and typed 192.168.1.1. Entered password to go into router and upgraded firmware. 2. 5 Ghz Settings: Went to Wireless menu. Selected "manual", mode is "mixed" (If i chose N only for 5 Ghz, then It won't save my setting for internet security. Instead it will be "disable" no matter what". The rest was default. SSID is enabled. Then I set up the 2.5 Ghz. I have 3 other computers with N wireless card. Some others have G, however when I viewed available networks, I only see the 2.4 Ghz ssid. I tried to reboot and unplug power for 10 seconds, but no luck seeing the 5 Ghz.
ive tried all types of things i read online and it is stuck on moderate no matter what i do, im hooked into router directly, when i hook directly into modem it switches to open.
View 2 Replies View RelatedHere is where I want to go:
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies View RelatedI have had no problems with my WRt610N fo 2 years. Yesterday a problem occured and today again. Namely, I opened my laptop (the lid) and suddenly it could not see my network (SSID) among the rest of the neighbouring ones. The WiFi indicator in the tray showed the yellow "!". Since I have another (secondary) router wired to the primary (WRT610N) I tried and succeeded to connect to it (same SSID, but type "g").
Today the same situation. This is the straneg thing - if I 1st connect to the "g" router after a while the WIn7 reports my SSID being of type "gn" meaning it now sees the primary WRT610N. If I switch off the secondary the netowork is maintained by the primary router showing "n". It seems like my laptop cannot see my router (but can see all other networks) until it 1sr connects to the secondary, and afterwards it sees the primary router and can stay with it.
Is LinkLogger the only option for reading logs on the WRT610Nv2? I read about Linksys's own software called LogViewer 1.14 but I can't find it.
View 3 Replies View RelatedI've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
View 9 Replies View RelatedI am trying to filter a URL, facebook and it is not working. I have tried rebooting the router and it is still allowing access. I have provided the settings and ranges for PCs.
View 3 Replies View RelatedMy WRT610n went out today for no apparent reason.All of my other peripherals are still running, but the router won't turn on. I've tried different transformers, outlets and powerstrips, with no luck -- no power. I've also tried a hard reset on it, with no luck.
View 3 Replies View RelatedHow is it possible to block facebook (or other sites) on WRT610N router, given that I have already set up Internet Access restrictions based on day/hour ?
View 9 Replies View Related