Linksys Wireless Router :: WRT610N Connected To Ethernet Port Of Previous Internet Modem
Dec 2, 2011
I was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
View 4 Replies
ADVERTISEMENT
Jul 8, 2011
My main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
View 1 Replies
View Related
Dec 25, 2012
I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.
View 3 Replies
View Related
Jan 18, 2012
I have DOCSIS 3.0 modem and a Linksys E1000 wireless router with which I get reults from SpeedTest of 8.6 mps down, 1.57 mps up up from 15 mps service from cable provider. Connected to modem via ethernet cable produces 16.0 speeds. Do I need to upgrade the router or are my settings wrong?
View 1 Replies
View Related
Jul 3, 2012
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies
View Related
Jan 12, 2010
I have a need to have 2 seperate networks from my comcast cable modem.I was hoping to plug a 5 port hub into the cable modem and then plug both the wrt610n and the wrt54g into the hub. Seem that only one of the routers will get an ip assigned from Comcast.Is there a way to have one ISP cable modem and create two different home networks with the two linksys routers, thus two separate independent networks?
-Network 1: public household use and family (Jane's wireless laptop, household PC's etc).
-Network 2: private household/company use and separate from the public family network (company wireless laptop/company PC, un-secure media server).
View 7 Replies
View Related
Jun 26, 2012
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies
View Related
Feb 14, 2013
I have the DIR-655, Rev. B running 2.07NA firmware, and have a strange problem with my wired clients. I have my primary computer/desktop PC connected via wired connection. I also have several wireless clients (laptop, iPad, iPhones, etc.). All have been performing normally. However, in December I connected a wired weather internet bridge to another ethernet port on the DIR-655.
It functions as it is supposed to, and all other connected devices do as well. But here's the problem - whenever I use the desktop PC (the only other wired connection) to do anything on the internet (mostly just web browsing ... I don't stream media from the internet on it, I don't do torrents....nothing out of the ordinary, and nothing really of high bandwidth), the wired weather bridge cannot communicate with its associated website. This continues as long as I'm using the desktop PC. When I stop using the desktop, the weather bridge resumes normally.
I have researched the weather bridge, and it is simply doing POST transactions (or so I'm told) to the website listening to it. It doesn't wait for acknowledgements or anything...just keeps POSTing updates. I tried reserving an IP for the weather bridge and the desktop, enabling QoS, and prioritizing the weather bridge (100 vs. desktop at 125), but it didn't work. I've tried moving the weather bridge into the DMZ. I'm totally baffled how just using the desktop to browse the internet could completely block the traffic from the weather bridge.
On the weather bridge support site, they suggested that I insure I'm not connected in gigabit speeds from my computer to the router, because in the past that has been known to cause issues on clients not running that speed, but I don't think my desktop is connected in that fashion. According to the settings, it can do 10 or 100, full or half. I have it set to AUTO.
View 3 Replies
View Related
Mar 14, 2011
how do you set up an ethernet port for DHCP with a Belkin ADSl modem with wireless G router, model number F5D7632-4?
View 1 Replies
View Related
Jun 10, 2012
So I have a Westell 7500 Modem/Router with Century Link DSL. I've been running a couple of laptops and my wifi enabled TV on the wireless. A few days ago I got a new desktop PC (Windows 7) and plugged the ethernet cable into it. Everything was great but the wireless was a bit slow for the TV so I plugged that in with an ethernet cable too. No problems for a few days. Today, we had a power blip and everything reset and I noticed that the internet light on the modem was solid red and I couldn't access the internet on any machine (ethernet or wifi). I called the ISP who said there was an outage in the area. A few hours later, solid green light on the modem BUT the TV (ethernet connected), my iphone, and my laptops could NOT connect, despite the network showing up with a full signal. Oddly, my new PC, connected via ethernet was fine so I played some Diablo (side note). Here's the deal: the new PC connects just fine but nothing else will. If I unplug the ethernet cable to the PC or disable the LAN connection, the red internet light appears on the modem. It seems as though the PC has hijacked the modem in some way. Even the TV won't connect with the ethernet cable. The only way the internet works now is if the modem is connected to the new PC. I've done all the resents - unplugged the modem and let it sit for 10-15 minutes, accessed the router settings, etc etc. Why would this start happening now after everything was working well for several days and how do I fix it? I need the wifi connection! Update: Plugged my Macbook Pro into the ethernet cable (took it out of new PC) and it works.
View 1 Replies
View Related
Jun 24, 2012
I've been using a WRT120N on a local area connection.The WRT120N acts as a gateway and also to connect to the PPOE connection, via a bridged adsl modem.I've noticed that the LAN port 1 was flashing although the network cable was disconnected from the physical port. I've restarted a few times but to no avail as well. Ever since that, I've noticed that connection through cable are unstable and hard.Now, I'm not able to reset or upgrade the router's firmware.Is there any other way to be done so that I can get this router working as normal again.
View 6 Replies
View Related
Feb 10, 2011
My computer ethernet port recognizes any modem but will not recognize any wireless routers. My ISP (DSL) spent 3 hours on the phone with me and can't figure it out. I have also contacted Gateway, figuring it must be my computer. I make money on the side fixing computers, so I do have a good idea as to what is what. I run Win7 on a Gateway DX4822 with Intel Pentium Dou-core. I have searched and searched for months and have found nothing. I have asked this question on various forums (including Microsoft) and still nothing.
I have wireless connectivity with a USB 2.0 WAN antenna. I also have a blu-ray player, XBox 360, and Wii all hooked up through this router. The player and XBox are wired, the Wii and a printer is wireless.I have had all things disconnected while trying to solve this issue, thinking that somehow there wasn't enough juice getting through. The cable works. I have tried resets, powerdowns, restarts, system recovery (at one point for a few days it did work as I shared internet from a friend upstairs from me), system restore, many different wireless routers AND modems. With the router connected, the ethernet port light does NOT come on. With the modem directly connected, the light DOES come on. Other computers/laptops in the house work wired into the router.
View 6 Replies
View Related
Jun 29, 2011
I have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies
View Related
Apr 23, 2012
I am trying to access the internet trough my WRT610N connected to a ZyXEL P-2601HN provided by my ISP.
I have the WRT610 all setup and working, but I cannot connect to the internet. The WRT610N is a the latest firmware version.
The WRT610 is connected (Internet) by cable to the Zyxel (one of the four ports)with a cat.5E patch cable.
the wireless is so much better on the WRT610N than the ZyXel.
View 3 Replies
View Related
Jan 9, 2011
The Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies
View Related
Sep 23, 2011
I am trying to configurate a WRT610N router that is connected to an ADSL modem.
I set this as DHCP, but in the status page I am only getting the Internet Address of 127.0.0.1.
The ADSL modem IP is 192.168.1.1, but I cannot have access to the modem configuration,
View 1 Replies
View Related
Sep 16, 2011
watch netflix on my tv,which has netflix,but has a Ethernet connection,and must use a rj45 cable,can I change it over to a wireless signal,so I won';t have to use a cable?
View 1 Replies
View Related
Feb 17, 2013
I'm using a refurbished WRT54G2 v1.5 router. I've had the router for two and a half years and have never had a problem. I recently unplugged my DSL modem and this router to move them, and when I plugged them in again, the router stopped picking up the internet signal from the DSL modem. I'm able to get internet when I hardwire directly to the modem though. I tried resetting the router and setting the router up from scratch again, but now I just get error 321 Ethernet cable not connected when I try and run the setup cd.
View 6 Replies
View Related
Nov 19, 2011
Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router. If I reset the cable modem, it will work for 10-15 minutes until it errors out again. If I plug the PS3 directly into the cable modem, it works fine. I'm really confused. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems.
View 8 Replies
View Related
Feb 1, 2013
Running Windows 8--64 bit computer, with a SBV4200 Voice over IP cable Modem (Time-Warner Communications), in home network. Longstanding problem with Ethernet connected computer losing connectivity to E3200. Connectivity reestablished by powering down, cutting power to cable modem, computer, and E3200, and restarting. Other wireless connections (iphones, ipad, other dos -based laptops have no problems--never any loss of connectivity. Things I have done to date: removed Linksys E-series software and reloaded, updated drivers, changed all wiring to router, and checked IP addresses and they are different.
View 2 Replies
View Related
May 8, 2011
I own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies
View Related
May 23, 2012
I just bought a WRT54GL router, and am following the CD instructions for installation. Everything is connected according to picture (cable to modem to router to computer), and my phone and computer are working properly. However, the router is telling me that it cannot connect, and to check the ethernet connection.earlier a screen popped up to enter a password, but it was under the checking status screen, so I was not able to enter one. how to get the modem connected.
View 3 Replies
View Related
Mar 26, 2013
Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies
View Related
Mar 25, 2012
Purchased today 26th March 2012, used CD first as warned, followed procedures, will not connect to WAG 160N modem router. WAG160N has MAC restrictions but MAC of WRT160N added, both in wireless and as a computer. Still won´t connect, gets to 85% in wireless connect mode then fails, gets to stage 4 of router recognition and fails, saying check cables. Cables changed to know working ones, still no success. Tried pinging 192.168.1.1 direct from computer with no success, no access to router log-in page at all. WAG 160N has no problems.
View 2 Replies
View Related
Dec 28, 2008
I am trying to install my router but I keep getting the error message that my ethernet cables are not connected. I have tried several times and everytime I know that the cables are in correctly. Is there anyway to solve this problem?
I am running in XP and my router is WRT54G2.
View 5 Replies
View Related
Mar 23, 2011
Every day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies
View Related
Nov 1, 2011
I have a 2wire modem and I'm using att DSL. The internet was working fine, I went out of town for 2 days, I returned to find my internet wont work. During the time I was out my brother said it hadn't worked for the 2 days. The modem works fine and all lights are green when my desktop is turned off or not connected. It even lets my brother use wireless on his laptop. However, when I turn on my computer or when I connect it to the modem with an ethernet cord, the DSL light will go red and not work.
View 7 Replies
View Related
Mar 6, 2013
We have a E3200 wireless router but our only connection is wireless. There is no Ethernet connection or cable modem. Presently I am unable to bring up the web page ie...10.100.x.x for entering the id/pw to login. Router is setup with default settings. Is there a setting that needs to be changed from the setup menu or this type of setup will not work with this router.
View 9 Replies
View Related
Feb 18, 2012
I have a problem with current (1.0.06) firmware on WRT120N. Few hours after restart DHCP server stops assigning IP addresses. Another restart resolves problem, but only for next few hours.Computers and other devices "see" my wireless network and they are able to connect to it, but the process stops at requesting IP number.There was no such effect with original firmware (although there was another problem with 2200BG), so I want to downgrade.where can I find previous versions of WRT120N firmware?
View 2 Replies
View Related
Mar 30, 2013
I recently upgraded to the EA6500 from the EA4500, however under Linksys Smart Wifi i can still see "EA4500 (offline)".
View 1 Replies
View Related
Dec 27, 2012
I have an E4200 router with 3 WET610N access points. I did the firmware update on the E4200 router about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.
I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update. And this equipment was working fine before this. Is there a way I can restore the previous version of firmware?
View 4 Replies
View Related
Apr 22, 2011
A friend recently re-installed windows XP on their HP Laptop. They were connected wirelessly with a Linsys router (model wrt54g.1) and an RCA Cable Modem. The Cable ISP can ping the modem and gave me the IP address over the phone. I cannot ping the modem even when I take the router out of the loop. The network card (i1394) in the Laptop is functioning normally and I can see traffic on the modem (both the Cable Internet light and the PC activity light are flashing green) the ethernet port on the laptop is also flashing (amber). However I cannot reach the internet and cannot even ping the modem. The modem is brand new..
View 2 Replies
View Related
Oct 30, 2011
I have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies
View Related
